EUROM 351651 Safe t Shine 1200 Compact Radiant Heater Instruction Manual

: June 12, 2024
: EUROM

Table of Contents

EUROM 351651 Safe t Shine 1200 Compact Radiant Heater
Technical data
Warning electric heaters
Description
Use and operation
Safety features
Cleaning and maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EUROM 351651 Safe t Shine 1200 Compact Radiant Heater

Thank you
Thank you very much for choosing for a EUROM device. You have made a good choice! We hope you will be satisfied about its functioning. To get maximum profit from your product, it is important to read this manual attentive and totally before use, and to understand what is written. Read especially the safety instructions: they are there to protect you and your environment. Keep the manual in a safe place for future reference. Store also the package: that is the best protection for your product in times of no-use. And if you at any time pass the appliance on, pass on the manual and package too

This manual has been complied with the utmost care. Nevertheless, we reserve the right to optimize this manual at any time and to adjust it technically. The image used may differ.

Symbol explanation

Do not cover the device!

Technical data

Supply voltage: 220-240V~50Hz
Maximum capacity: 1200 Watt
Settings: 0-400-800-1200 Watt
Oscillating: +
Dimensions: 22 x 32 x 50 cm
Weight: 1,44 kg

Warning electric heaters

Safety warning – general

Read the user instructions carefully and completely before using (and installing) this device. Keep the instruction leaflet somewhere safe so that you can consult it and pass it on in future.
Before use, check your new device (including cable and plug) for any visible damage. Never use a damaged device but take it back to the supplier for a replacement.
In the event of incorrect usage or installation, there is a risk of electric shocks and/or a fire hazard.

Warnings positon device

Only use the device when the foot have been installed. Using the device without foot creates a significant risk of fire. Always remove the plug from the socket if you are installing/removing.
This device is not suitable for wall or ceiling installation.
Do not use this device in the immediate vicinity of a bath, shower or swimming pool.
This device is not suitable for use in damp spaces such as bathrooms, wash rooms etc. Never locate the device near water-points and reservoirs (tap, bath, shower, toilet, sink, swimming pool, etc.). Make sure that the device cannot fall into water and that it cannot be penetrated by water. If the device falls into water make sure you remove the plug from the socket! Do not use a device that is wet inside but take it to be repaired. Never immerse the device, cable or plug in water or any other fluid and never touch device with wet hands.
The air around the device must be able to circulate freely. Never install it too close to walls or large objects and never under a shelf, cupboard, curtains or similar. When locating the device, make sure you have the following minimum free space:
Front, minimum free space 100 cm
Back, minimum free space 50 cm
Sides, minimum free space 50 cm
Top, minimum free space 100 cm
Always place the unit on a sturdy, flat horizontal surface
The base on which the device is placed must not be made of flammable materials.
It must be resistant to temperatures of at least 125°C without burning, melting, deforming or bursting into flames.
Check regularly to ensure that the surface is not overheating; this could be dangerous!
Never place the device on surfaces such as beds or deep-pile carpet, the device may fall over.
Do not place the device near an open window as rain could blow in; do not place on wet surfaces and avoid any liquids being spilt nearby. Do not place the device behind a door or along a walking route to avoid accidental trips.
Do not place the device near, under or facing an electrical socket and not in the vicinity of an open fire or heat source.
Do not use the device nearby or facing furniture, curtains, paper, clothing, bedding or other flammable materials. Keep at least 1 metre from device!
Do not use the heater outdoors or in areas that are smaller than 15m³.
The device contains hot and/or glowing and sparking components. Do not, therefore, use where fuels, paint, flammable fluids and/or gases are stored.
Do not use the device in an environment that poses a fire risk, e.g. near gas tanks, gas pipes or aerosols. This is an explosion and fire risk!

Warnings – use

Do not use additions/accessories on the device that have not been supplied or approved by the manufacturer.
Only use the device for its intended purpose and in the manner set out in this instruction leaflet.
Some parts of this device will get very hot and could cause burns. You must pay particular attention to children, vulnerable persons and pets that are present near the device. Never leave them alone with a working device.
Never cover or block the device; it will overheat and this could lead to a fire risk. Never hang or place objects such as clothing, blankets, cushions, paper, etc. on the device. The minimum distance of 1 metre between the device and flammable materials must always be applied. Ventilation openings should never be blocked as this may pose a fire risk. Never use the device to dry clothing or place anything on it. Do not let anything lean against the device!
Do not set the device to come on automatically using a timer, clock or other facility. You must always check for safe conditions before using the fireplace! Never use the device with an external voltage regulator such as a dimmer or similar, as this could be dangerous!
The device is exclusively intended for normal, household usage. Only use for providing heat in your home.
The connection voltage and frequency, as given on the device, must correspond to that of the socket to be used. The electrical socket to be used must be an earthed connection. The electrical installation must be protected via a 30 mA earth leakage circuit breaker. The electrical socket that you are using must be to hand at all times in order to be able to remove the plug from the socket in the event of an emergency.
To avoid overloading and/or fuses being blown, do not use any other equipment on the same socket or electrical group as the one used for the device.
Unroll the electric cable for the device fully before inserting the plug into the socket and ensure that the electrical cable does not come into contact with the fireplace or get hot. Do not run the electrical cable under carpet, cover with mats, runners or similar and do not place in areas that are walked on frequently. Ensure that it cannot be stepped on and that no furniture is placed on top of it. Do not bend the electrical cable around sharp corners and do not roll up too tightly after use! Prevent the electrical cable coming into contact with oil, solvents and sharp objects. Check the cable and plug regularly for damage. Do not bend or pinch the electrical cable and do not wind it around the device; this could damage the insulation!
10. The use of an extension cable is not advised as this can lead to overheating and fire. If the use of an extension cable is unavoidable, make sure that it is not damaged and that it is an approved extension cable with a minimum diameter of 3×1,5mm² and a minimum permitted capacity of 1500 Watt. Always fully extend the cable in order to prevent overheating.
Only connect the device to a fixed socket. Do not use multi-plug adapters or similar.
During use, the plug may begin to feel warm; this is normal. If it’s really warm, there may be something wrong with the socket. Please contact your electrician.
Always turn off the device and remove the plug from the power socket: Never turn the device off using the plug!
Prevent foreign objects entering the radiation/ventilation or outlet openings on the device. This may cause electric shock, fire or damage.
Never leave a working device unattended but switch off and then remove the plug from the socket.
Always remove the plug from the socket when the unit is not in use! Always remove plug by pulling on the plug itself; never pull on the electrical cable!
This device gets hot during use. Never touch the device when it is on or shortly thereafter; it could burn you.
This device is not equipped to monitor the ambient temperature in the room. Do not use the device in small rooms if these rooms are used by persons who are not capable of leaving the room independently, unless there is constant supervision.
Never operate the device with wet hands.

Warnings by whom the device may be used

Children younger than 3 must be kept out of the vicinity of the device unless they are continuously supervised.
Children between the ages of 3 and 8 may only switch the device on or off if it is set up or installed at its usual location and they are supervised or have received instructions regarding the safe use of the device and understand the corresponding hazards. Children between the ages of 3 and 8 may not insert the plug into the socket, adjust the device settings or clean or maintain it.
This device can only be used by children from the age of 8 and elderly persons and persons with diminished physical or mental capacities or a lack of experience and expertise if they are supervised or have received instructions regarding the safe use of the device and understand the corresponding hazards.
Children may not clean or maintain the device without supervision.
Children may not play with the device.

Warnings for maintenance

Keep the device clean. Dust, dirt and/or deposits in the device often lead to overheating. Ensure that this type of build-up is regularly removed.
Always switch the device off, remove plug from socket and let the device cool down before you:
- clean the device
- users maintain the device.
- touch or move the device.
Never switch the device on if you have noticed damage to the device itself, the cable or plug or if it does not work properly, makes strange noises, smells odd or you can see smoke, or if it has fallen or shows any other signs of damage. Remove the plug from the socket immediately. Take the entire device back to your supplier or a recognised electrician to be checked and/or repaired. Always ask for original parts to be used.
The device may only be opened and/or repaired by a competent and qualified person. Do not carry our your own repairs as this could be dangerous! Repairs carried out by unauthorised persons or changes made to the device could damage the dust/waterproof capacity of the device and will nullify the guarantee and the manufacturer’s liability.
If the electrical cable is damaged, it must be replaced by the manufacturer, their service department or somebody with similar qualifications in order to prevent creating a hazard.

Failing to adhere to points 3, 4, 5, could lead to damage, fire and/or personal injury. They will invalidate the guarantee and the supplier, importer and/or manufacturer shall not be liable for the consequences.

Description

On / Off switch upper halogen lamp
On / Off switch, middle halogen lamp
On / Off switch lower halogen lamp
Oscillation switch
Housing
Radiation grille
Halogen lamp
Reflector
Radiation grille
Grill
Housing
Foot
Handle
Electric cable with plug
Fixing screws
Anti-tip protection
Electrical cable guide

Assembly, location and connection
Remove all packaging material and keep out of reach of children. After removing packaging, check the appliance for damage or other signs that could indicate a
fault/defect/malfunction. In case of doubt, do not use the appliance, but contact your vendor for inspection or replacement.
The device consists of two parts that you must fit together before use: the actual device and the base.

Lead the electrical cable with plug through the middle hole in the base; from top to bottom (the hollow side of the base is the underside).
Now slide the base over the small white box with the electrical cable on the underside of the device: all hollow spaces and protrusions and screw holes on top of each other. It only fits in one way.
Now firmly fasten the base and the device together using the two safety screws included in the package.
Select a suitable location for the device taking into account all the warnings mentioned earlier in this manual.
Lead the electrical cable through the cable clamps and recess to outside the base and place the device upright

Caution: A push button is located beneath the heater: this is the safety tip-over cut-out switch. Knocking over the heater will cause this button to protrude and the heater will turn off automatically. This means the heater will not work when hanging.

Use and operation

Check that all buttons are turned off, ie not pressed.
Unwind the electrical cable completely and insert the plug into a suitable 220-240V earthed socket.
Select the desired heating level by pressing the On / Off switches (1, 2, 3)
The heater has 3 heating elements of 400 W each, which can be switched on separately.
Now when you press the oscillation switch (4), the device will pivot approximately 90 °horizontally. Pressing this switch again switches the function off.
To switch off the appliance, all switches press O individually. Then remove the plug from the socket. Never leave the heater connected to the power supply when it is not in use!
Note: When you use the heater for the first time, it may smoke slightly and give off an odor. This is normal and harmless and should disappear after a few minutes. If this does not happen and the heater continues to smoke, switch off all the heating elements and remove the plug from the socket and contact your supplier.
The heater, and particularly the radiation grid, become extremely hot during use and will also remain warm for some time after the heater has been switched off. Take this into account!
If you wish to relocate the heater, first switch it off, remove the plug from the socket and allow it to cool down before moving it. To relocate the heater, use the handle.

Safety features

Overheating protection
The device is equipped with an overheating protection, which switches it off automatically in case of internal overheating. Switch the device off, unplug the power plug, remove the source of overheating, let the device cool down and use as normal. Do not use the device if the source of overheating cannot be traced or if the problem persists, but always contact your supplier.

Tipping safeguard
The heater is fitted with a tipping safeguard which automatically shuts off the appliance if it inadvertently falls over. However, this does not rule out all risks: even after the heater has been switched off, it and particularly the radiation grid, will remain very hot for some time and if it is left lying, for example, on a wooden floor or carpet, it can cause fire/melting/scorching damage and result in a fire. Therefore remain cautious at all times! When the heater is returned to its upright position, it will resume functioning as normal but, before reusing, switch off, unplug and check for damage. Do not use the heater if it is damaged or malfunctioning, but have it inspected/repaired!

Cleaning and maintenance

Keep the heater clean. Dust, dirt and/or deposits in the heater are a common cause of damage or faults! So these should be removed regularly. Switch off the heater, remove the plug from the socket and allow the heater to cool down before cleaning or carrying out maintenance work.

Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use aggressive soaps, sprays, cleaners or abrasives, waxes, polishes or chemical solutions!
Using a vacuum cleaner, carefully remove any dust and dirt from the grills. Be careful not to touch or damage any internal parts during cleaning!
The heater contains no other parts which need maintenance.
At the end of the season, store the cleaned heater in the original packaging if necessary. Store it upright in a cool, dry and dust-free place.

Disposal
At its end of life, discard the device according to the local laws and regulations, or deliver the device to your supplier.

We wish you a lot of fun with the Safe-t-Shine 1200 compact!

Contact