nathan james 13111 Mable Farmhouse Bathroom 31 Inch 3-Lights Vanity Light Fixture Instruction Manual
- June 12, 2024
- NATHAN JAMES
Table of Contents
nathan james 13111 Mable Farmhouse Bathroom 31 Inch 3-Lights Vanity Light
Fixture
Ok, let’s get rolling
This should be easy, just follow our instructions and you will be back to
Netflix in no time.
What you need
- Your favorite snack or energy bar (Save the bubbly for once your fixture is safely installed!)
- Use the packaging carton as a working surface to prevent product damage during assembly
What’s included
| Description | Qty | |
|---|---|---|
| A | Fixture | 1 |
| B | Mounting Plate | 1 |
| C | Finial Cap | 2 |
| D | M4*25mm Mounting Screws | 2 |
| E | Wire Nuts | 3 |
| F | Metal Shade | 3 |
Safety first, fun later
Safe use of this product starts with you.
Use this light fixture responsibly with the primary concern for your safety.
Follow assembly instructions carefully and inspect product upon receipt and
each use.
Nathan James and its parent companies cannot be held legally responsible for
any injuries or death resulted from failure to follow instructions or improper
use of this product.
Do not modify the structure of this product in any way.
Our products have been tested to meet specific safety measures as they were
originally intended to be sold. Any modifications will present the risk of
creating significant safety issues which Nathan James will not be responsible
for.
Proper use
- DO NOT use for commercial purposes
- DO NOT leave spilled liquid on fixture
- DO NOT use light fixture if damaged
- DO NOT make temporary repairs
- DO NOT use outdoors
WARNING
Inspect the wire insulation for any cuts, abrasions, or exposed copper that
may have occurred during shipping. If there is a defect in the wire, do not
attempt installation. Please reach out to our Customer Happiness team at
[email protected] or
1-866-619-1004
WARNING: RISK OF ELECTRIC SHOCK
Before starting the installation, disconnect the power by turning off the
circuit breaker or by removing the appropriate fuse at the fuse box. Turning
the power off at the switch is NOT SUFFICIENT to prevent electrical shock.
PLEASE CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS.
The goods
IMPORTANT
- Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes.
- Do not over tighten screws and bolts to avoid stripping.
- Please use hand tools to assemble this product. Do not use power tools.
Pre-Installation
- Read all instructions prior to beginning assembly.
- To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.
- Keep the receipt and these instructions for proof of purchase.
- Use 3 Type A or Type ST Vintage Bulbs or 13W LED Bulbs (not included).
- 120V 60Hz AC Only
Step 1
Woohoo, it’s time to get started! Don’t worry, this should be quick and
easy—you’ll be back watching Netflix in 20 minutes.
First, remove the Mounting Plate (B) from Fixture’s (A) backplate by removing
the Finial Caps (C).
Step 2
Next, secure the Mounting Plate (B) to the electrical box using the Mounting
Screws (D).
Step 3
Install horizontal support tubes to the back of the Fixture Body (A) by
threading them into place.
Step 4
Install the fixture back plate. Be sure to take notice of how the ground wire
with lug must be installed.
Step 5
Wrap the ground wire from the Fixture (A) around the grounding screw on the
Mounting Plate (B) and secure in place with a screwdriver.
Step 6
Use Wire Nuts (E) to connect the matching colored wires (white to white, black
to black and ground to ground). Once complete, tuck the excess wire into the
electrical box.
Note: Be sure that you are only making the connections to a 120V AC 60Hz circuit. If you do not have a pre-existing electrical box, we strongly advise using a certified electrician.
Step 7
Secure Fixture (A) to screws on the mounting plate with Finial Caps (C). Be
sure to tuck all of the excess wires into the electrical box.
Step 8
Install the three Metal Shades (F) to the Fixture (A) with the shade ring
collar on the outside of each socket assembly.
And voila, you’re all done! Now you just need to screw in some bulbs (see the
pre-installation instructions on page 5 for our recommendations) and let there
be light!
Troubleshooting
| Problem | Possible Causes | Solutions |
|---|---|---|
| The bulb will not light. | The bulb is burned out. | Replace the light bulb. |
| The power is off. | Ensure the power supply is on. | |
| The circuit breaker is off. | Ensure the circuit breaker is in the ON position. | |
| The fuse blows or circuit breaker blows when the light is turned on. | There is | |
| an exposed wire. | Discontinue use of the light. |
Contact a qualified electrician or reach out to our Customer Happiness team at [email protected] or 1-866-619-1004.
Questions? Don’t worry, we’ve got the answers
What other light bulbs can fit in this light?
The bulb must not be greater than the max wattage for the fixture. It must
match the base size, and the diameter of any area of the bulb should be less
than diameter of any area of shade, so that it can fit.
Can I use an LED light bulb?
Yes, so long that the base size matches and the diameter of any area of bulb
is less than diameter of any area of shade, so that it can fit.
Is this UL/ETL certified?
Yes, all our products are either UL or ETL.
Do I need an electrician to set up the hardwire?
We recommend using a certified electrician for all hardwiring, although all of
our fixtures can be set up without an electrician, as long as you are
replacing an existing fixture or have an existing junction box ready for a
fixture installation. ENSURE POWER IS OFF WHEN INSTALLING. For all new
constructions, please use a certified electrician.
Can I retrofit this hard-wired to a plug-in or vice-versa?
Yes, a plug-in fixture can be turned into a hardwire fixture and a hardwire
fixture can become a plug-in fixture. For many products we will provide all
the necessary hardware to make these changes, if not, you will need to
purchase the necessary hardware.
Is this light compatible outside North America?
Our lighting is only warranted in Canada and the United States.
What do I do if the product is not working?
Try a different light bulb and confirm proper installation.
Can these lights work on a dimmer?
Dimmability is related to the light bulb and the wall switch, not the light
fixture. All our hardwire fixtures are compatible with dimmable light bulbs.
We recommend using a dimmer switch, as it extends the life of the bulb and
allows for energy saving and great ambiance. If using a LED bulb, please
ensure both your LED bulb and dimmer switch are compatible.
Can I use the fixture outdoors?
For vanity light fixtures, we have a damp rating, which approves the use in
bathrooms or other damp areas, but is not approved for outdoor use unless
specified.
No heartburn, when we handle the return
Give us a call 1-866-619-1004 or shoot
us a message at [email protected] we will
issue you a free replacement with zero hassle.
We really don’t want you to go through the hassle of re-packaging your item and sending it back, because let’s be honest…nobody has time for that.
We are only in business if you’re happy
For starters, thanks for being you.
- Toll-free at 1-866-619-1004
- [email protected]
- NathanJames.com/help
We do our best to ensure your furniture arrives without any problems, but occasionally mistakes happen—as humans we are imperfect beings. In the event that a part is damaged or missing, we will be more than happy to provide you with replacement part(s) for free.
Warranty
This product comes with a lifetime warranty from the date of purchase. Please use your phone to scan the QR code to register your product or visit https://goo.gl/i9dk3q
Did we do alright? Please spread the love!
If you are happy with your product, tell your friends and family about us or
even better leave us a review online. Spreading the word gives us the
opportunity to make more people happy and keep our prices low for your next
purchase.