TeKO PSE Series Photoelectric Sensor Instruction Manual

: June 12, 2024
: TEKO

Table of Contents

Precautions
Safety Warning
Scrap Treatment
Technical speciﬁcations
Dimensions
Button instruction
Mounting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PSE Series Photoelectric Sensor
Instruction Manual **** PSE series
Photoelectric sensor
Operation manual
teko-com.ru
Tel.: 8 (800) 333-70-75
E-mail: sale@teko-com.ru

Precautions

The maximum allowable voltage of the sensor is 10% of the rated voltage, Please confirm that the supply voltage is less than the maximum allowable value before powering on
The time from powering-on to normal detection of the sensor is 100ms, please ensure that the sensor is used after 100ms of powering-on
When using different power sources for the sensor and load, be sure to turn on the power of the sensor first
When the sensor is not used, it is recommended to cut off the power of the load first and then turn off the power of the sensor
When installing the sensor, do not subject the sensor to severe external force (such as hammering, etc.), which may damage the sensor performance
Avoid using thinner, alcohol or other organic solvents when cleaning

Safety Warning

Do not use in an environment with flammable, explosive or corrosive gases
Do not use in oil or chemical environments
Do not use in a high humidity environment
Do not use in direct sunlight
Do not use in other environmental conditions that exceed the rated value
Do not disassemble, repair or modify this product without authorization

Scrap Treatment

When the product is scrapped, please dispose of it as industrial waste

Technical speciﬁcations

Detection type| Through beam| Polarized reflection| Diffuse reflection| Wide- angle
---|---|---|---|---

Model

Indicator

| Green| Power, stable signal(unstable signal flash)
Yellow| Output, overload or short circuit(flash)
Anti-ambient light| Anti-ambient light interference≤10,000lux; Anti- incandescent light interference≤3,000lux
Ambient temperature| -25℃…55℃
Storage temperature| -25℃…70℃
Protection degree| IP67
Certification| CE
Production standards| EN60947-5-2:2012 、 IEC60947-5-2:2012
Material| Housing material: ABS ； Filter: PMMA
Weight| Cable:about 50g ； Connector:about 10g
Accessories| Operation manual,screw,reflector OR12(only for polarized reflection sensor) 、 Mounting bracket ZJP-8

*The data is the result of the PSE polarized reflection sensor with standard reflector OR12.
Wiring diagra

Through Beam-receiver, Diffuse Reflection, Polarized Reflection, Wide-angle- NPN Output| TeKO PSE Series Photoelectric Sensor - diagram
1
---|---
Through Beam-Emitter|
Through Beam-receiver, Diffuse Reflection, Polarized Reflection, Wide-angle- PNP Output|

Terminal Wiring Diagram

Through Beam-Emitter| Diffuse Reflection,Wide-angle Polarized Reflection, Through Beam-Receiver
---|---
|
BN ： +
BU ：| BN ： +
BU ： BK
BK： OUT

Dimensions

Through Beam, Diffuse Reflection,Polarized Reflection, Wide-angle| Through Beam, Diffuse Reflection,Polarized Reflection, Wide-angle
---|---
TeKO PSE Series Photoelectric Sensor - diagram 4

 Accessory Dimensions （ Sold Separately） TeKO PSE Series Photoelectric
Sensor - diagram 5

Button instruction

1.Press the button for the duration time “t”, if t<2s or t≥8s, the setting is invalid, NO/NC maintains in the original state, and the product distance maintains the original;
2.Put the product in face to the sensing object, and press the button for the duration “t”, if 2s ≤ t < 5s, the yellow and green lights flash synchronously at 4 Hz, when the button is released to finish distance setting.
as shown in the following figureNote: For distancing setting, if the distance between the sensing object and the sensor exceeds the detection ability of the product, in duration 2s ≤ t < 5s, the yellow and green lights flash synchronously at 4Hz, when the button is released to finish the distance setting but not successfully.
If the yellow and green lights flash asynchronously at 8 Hz, meaning that the product distance setting fails, and the product distance is automatically set to the maximum value, as shown in the following figure:3.Press the button for the duration “t”, if 5s≤t<8s, the yellow and green lights flash synchronously at 2 Hz, when the button is released to finish NO/NC state switchover.