Zyxel WX3100-T0 Dual Band Wireless AX1800 Gigabit Extender User Guide
- June 12, 2024
- ZYXEL
Table of Contents
COMMUNICATION
WX3100-T0
Dual-Band Wireless AX1800 Gigabit Extender
Quick Start Guide
Package Contents
| Device
---|---
| Power Adapter
| Ethernet Cable
| Quick Start Guide
| Declaration of Conformity Safety Warnings
Support Information
https
://service-provider.zyxel.com/global/en/tech-support
https://zyxelsp.com
/tech-support
See the User’s Guide at www.zyxel.com for more information, including customer
support and safety warnings.
EU Importer
Zyxel Communications A/S
Gladsaxevej 378, 2. th. 2860 Søborg, Denmark.
https://www.zyxel.com/dk/da/
UK Importer
Zyxel Communications UK Ltd.
2 Old Row Court, Rose Street, Wokingham,
RG40 1XZ, United Kingdom (UK)
https://www.zyxel.com/uk/en/
US Importer
Zyxel Communications, Inc.
1130 North Miller Street Anaheim, CA 92806-2001
https://www.zyxel.com/us/en/
Copyright © 2023 Zyxel and/or its affiliates. All Rights Reserved.
Setting Up the WX3100
- Attach the bracket to the bottom of the WX3100 as shown.
- Place the WX3100 where you want to extend your wireless network.
- Plug in the power adapter and turn on the WX3100. Wait for about 2 minutes. The Power C) LED lights up steady green.
MPro Mesh Network Scenario 1: With MPro Mesh Router
In this scenario, you have a Zyxel router that supports MPro Mesh. If you do
not, go to MPro Mesh Network Scenario 1: With Non-MPro Mesh Router and Two
WX3100s.
Note: To check if your Zyxel router supports MPro Mesh, scan the QR code
in the last page to see the MPro Mesh Router supported list.
Note: To set up your WX3100 with the MPro Mesh app, scan the QR code in
the last page.
-
Use the included Ethernet cable to connect the WX3100 LAN port to the MPro Mesh Router LAN port. Wait until the POWER and LINK LEDs are steady green.
-
Unplug the Ethernet and power cable from the WX3100.
-
Place the WX3100 where you want to extend your WiFi network.
-
Plug in the power adapter. Make sure your LINK LED is steady green (preferred) or amber.
For more details on the LEDs, please refer to the LED table.
Note: You do not need to plug in the Ethernet cable in this step. -
To add more extender to your network, repeat from step 1.
| Green
On – Power is on or the MPro Mesh configuration process is done.
Blinking – The WX3100-2 is starting up or under the MPro Mesh
configuration process.
Red
On – The WX3100-2 detects a system error.
Blinking (Fast) – The WX3100-2 is upgrading firmware.
Blinking (Slow) – The Easy Mesh process has failed.
---|---
| With Wireless Connection
Green
On – The WiFi connection to the WX3100-1 is good.
Amber
On – The signal is too strong. Suggest moving the WX3100-2 away from the
WX3100-1.
Red
On – The signal is too weak. Move the WX3100-2 closer to the WX3100-1.
With Wired Connection
Green
On – The Ethernet cable is connected to the WX3100-2 LAN port.
| Green
On – 2.4G/5G WiFi is ready.
Blinking – The WX3100-2 is transmitting/receiving WiFi data.
Off – 2.4G/5G WiFi is disabled.
| Amber
Blinking – The WPS is in process.
Off – The WPS process is done.
MPro Mesh Network Scenario 2: With Non-MPro Mesh Router and Two WX3100s
The WX3100 connected to the Non-MPro Mesh Router with an Ethernet cable is
hereafter referred to as the first WX3100 (WX3100-1)
- Use the included Ethernet cable to connect the first WX3100 (WX3100-1) LAN port to the Non-MPro Mesh Router LAN port. Wait until the POWER and LINK LEDs are steady green.
- Place the second WX3100 (WX3100-2) where you want to extend your WiFi network.
- Wait until the POWER and LINK LEDs on WX3100-2 are steady green (preferred) or amber to indicate that the auto-pairing is done. Move the WX3100-2 closer to the WX3100-1 if the LINK LED is red.
- Scan the QR code at the last page to install the MPro Mesh App to manage your WX3100-1.
| Green
On – Power is on or the MPro Mesh configuration process is done.
Blinking – The WX3100-2 is starting up or under the MPro Mesh
configuration process.
Red
On – The WX3100-2 detects a system error.
Blinking (Fast) – The WX3100-2 is upgrading firmware.
Blinking (Slow) – The Easy Mesh process has failed.
---|---
| With Wireless Connection
Green
On – The WiFi connection to the WX3100-1 is good.
Amber
On – The signal is too strong. Suggest moving the WX3100-2 away from the
WX3100-1.
Red
On – The signal is too weak. Move the WX3100-2 closer to the WX3100-1.
With Wired Connection
Green
On – The Ethernet cable is connected to the WX3100-2 LAN port.
| Green
On – 2.4G/5G WiFi is ready.
Blinking – The WX3100-2 is transmitting/receiving WiFi data.
Off – 2.4G/5G WiFi is disabled.
| Amber
Blinking – The WPS is in process.
Off – The WPS process is done.
Managing Your WX3100 Using the MPro Mesh App
| |
---|---|---
https://play.google.com/store/apps/details?id=zyxel.com.multyproneo|
https://apps.apple.com/us/app/mpro-
mesh/id1479660357
Download the MPro Mesh app to manage your WX3100.
Note: To manage your Mesh network, connect the MPro Mesh app to the
Controller (WX3100-1 in Scenario 1 or MPro Mesh Router in Scenario 2).
https://www.zyxel.com/library/sp/MPro_Mesh_supported_model_list.pdf
Scan this QR code to see a list of Zyxel devices that support MPro Mesh.
https://www.zyxel.com/library/sp/compact_user_guide_wx3100.pdf
Scan this QR code to see steps for setting up your WX3100 with the MPro Mesh
app.