nordlux Taklampa Utomhus Ceiling Lamp Installation Guide
- June 12, 2024
- nordlux
Table of Contents
Taklampa Utomhus Ceiling Lamp
Installation Guide
Mounting instruction
Taklampa Utomhus Ceiling Lamp
IP5X
IP5X: Dust is prevented from entering the lamp in amounts that can cause
damage to the function/safety of the lamp.
IPX4
IPX4: Raindrops falling from any angle will not affect the function/safety of
the lamp.
**** Class I: lamp has an earth terminal and must be connected to the
yellow/green earth wire.
The lamp is only suitable for connecting directly to the mains.
MAX 15W
Do not exceed the maximum wattage.
IMPORTANT! Always shut off power to the circuit before starting installation work. In some countries electrical installation work may only be carried out by a authorized electrical contractor. Contact your local electricity authority for advice.
**** Disposal of waste equipment by users in private households in the European Union. This symbol indicates that this product must not be disposed of with your other household waste. Electrical and electronic equipment contain substances which may cause damage to human health and environment if not recycled correctly. It is your responsibility to hand over to a designated collection point for recycling of waste electrical and electronic equipment. When handing over for correct recycling you help to prevent these products straining nature and environment unnecessarily and to protect human health. For more information regarding correct disposal, please contact your local city office, your household waste disposal service or the store where you purchased this product.
The mounting instruction must not be discarded
Parallel arranging possible.
General maintenance: Use a soft, dry cloth for dusting, and a soft, damp cloth to gently remove grease or similar stains. Never use any detergents or chemical reagents. Do not switch on the lamp before all the water has evaporated. Specifically for mouth-blown glass: Mouth-blown glass is formed manually. Because of this unique process, air bubbles may occur in the glass, just as the thickness of the glass may vary. This is to be seen as a natural consequence of the manual process and is what gives mouth-blown glass its character and organic look. Always clean mouth-blown glass when the glass is cold.
In Denmark, outdoor lightings must be mounted by an authorized electrician.
www.nordlux.com
Nordlux A/S – ∅stre Havnegade 34 – Dk-9000 Aalborg
We congratulate you on your new outdoor lamp!
We congratulate you on your new outdoor lamp!
Guarantee
The Nordlux Outdoor lamps in copper, brass, tombac and galvanized are
guaranteed for up to 15 years. This guarantee applies to extensive corrosion
in the form of holes in the metal caused by rust.
The guarantee is subject to presentation of receipt.
There is not guarantee on the components which have been damaged by wear and
tear or mistreatment of the lamps
Stainless steel
Remember to take care of your lamp. Just follow the guidelines below.
The shiny, uniform and decorative surface of stainless steel makes it very
suitable for outdoor use.
It is an alloy consisting of iron, chrome and nickel. During bath pickling, a
thin, rustproof oxide layer forms on the surface. The surface is continually
vulnerable to atmospheric conditions. and from other effects of the close
environment. This means that the lamp must be regularly maintained if its
surface is to remain shiny and untar- nished by rust.
Before setting it up, treat your lamp with acid-free oil, and dry it off with
a soft cloth. Repeat this three or four times a year. Stainless steel lamps
are not recommended for use in aggressive environments such as coastal,
agricultural or industrial areas.
Copper, Brass and Tombac fixtures
Our copper, brass and tombac fixtures are made from respectively solid
copper, brass and tombac. The mechanical machining will leave small scratches
in the surface, as well as residues of rinse aid. This rapidly disappears in
the patina process. After the first rain showers the copper / brass / tombak
surface will appear stained, but the aerated air and moisture will soon make
the lamp appear with dark brownish color.
Over the years, the material copper will get a beautiful patina-green cofor
and brass / tombac will get a darker and more uniform color. The uniformity of
the patina surface, as well as the rate at which the process occurs is
dependent on the environment that affect the fixture.
Hot-gatvanized lamps
The zinc treatment of the steel lamps is executed manually in plants. The
temperature of the melted zinc is about 460 degrees. When the lamps are dipped
in metted zinc a reaction between the metals occurs, which develops alloys in
the surface.
The lamp and the components of the lamp are manually dipped in the hot zinc.
This treatment leaves variations in the coating in the form of partly an
uneven surface and partly minor formations of drops.
Thin »zinc curtains« might also occur on the surface and they show as ‘a thin
film which hangs down from the edge of the lamp. This film can easily be
removed or brushed off with a soft brush.
Condensation
Condensation is a natural phenomenon arising under specific atmospheric
conditions. Damp heat and cold air meet. which causes condensation of water on
the surface.
When water heats up it leads to rising water vapour. which will be able to
affect electric components.
Condensation is not included by Nordlux warranty. unless it is possible to
prove that a technical ‘production error in the lighting causes entry of
water.
In case of condensation please check:
– If the lighting is mounted according to instructions. Washers should seal
tightly. Make sure to tension screws and lenses.
-In garden lightings rising damp from the ground may cause condensation in the metal post. This problem can be defeated by filling sealing material into the metal post.
Aluminium fixtures
Our aluminium light fixtures are made from die-cast and/or extruded
aluminium, where the light fixture’s design determines whether both types of
materials, or just one of them, are used for different parts of the same light
fixture. Aluminium light fixtures in raw aluminium are subsequently coated
with a special clear coat, which seals the surface to safeguard against
corrosion. Painted aluminium light fixtures are powder-coated and have a
uniform and smooth surface. To avoid the light fixture tarnishing, it is
recommended to clean and wipe the light fixture after mounting, and repeat
this process 3-4 times each year.
This is done with a regular cleaning agent. Black light fixtures which are
bleached by strong sunlight can also benefit from treatment with silicone
spray as needed, to maintain the black color. Mounting light fixtures in
coastal, agricultural or industrial areas is not recommended, as these
aggressive surroundings may cause the light fixture to corrode, which may
entail spalling, bubbles in the surface and a whitish incrustation on the
light fixture’s surface.
-It is highly important that drainage holes are kept free of impurities if any.
BEFORE ASSEMBLING THE BOLLARD AGAIN DO REMEMBER TO WIPE OFF ALL PARTS!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>