GIRA 5511 00 System 106 Flush-Mounted Housing Installation Guide
- June 12, 2024
- GIRA
Table of Contents
Installation instructions
System 106 flush-mounted housing1-gang to 5-gang
5511 00
5512 00
5513 00
5514 00
5515 00
5518 00
https://katalog.gira.de/de_DE/dir.html?id=584005
Scope of supply
For your safety
Electrical devices may only be installed and connected by a qualified
electrician.
These instructions are part of the product and mus tremain with the end
customer. Read the instructions before use and observe the notes Mounting
example: surface-mounted housing, 2-gang.
| 1 | 1 x | Function carrier |
|---|---|---|
| 2 | 1 x | Housing |
| 3 | 2 x | Schrauben (ø 6 mm) |
| 4 | 1 x | Screws |
| 5 | 1 x | System cables and terminating resistors (from 2-gang housing) |
| 6 | 1 x | Montageanleitung |
| 7 | 1 x | Bit holder and bit |
Dimensions
Mounting examples
Mounting preparation
Montagehöhe und Kabellänge beachten
Observe rcommended mounting height for camera (item no. 5561 00) or display
module (item no. 5561 00). Do not plan the cable bushing for the connection
cable at the height of these modules!
Recommendation: Use lower bushing with vertical mounting. The connection cable
should not be longer than max. 1.5 x the length of the used surface-mounted
housing.
Mounting in a front module
Here you can find the video for the installation:
https://bda.gira.de/VideoSys106EinbauWDVS
Select an opening (A) for the cable feed-through and pierce it with a round
object (no cross-shaped cut).
Never use the diaphragm (B) for the cable entry!
Completely feed the connection line through the opening and mount the housing
so that the distances between enclosure and front module are symmetrical.
Should the seal cap become detached during mounting, reinsert the seal cap and
check for correct positioning to ensure tightness.
Firmly push wall fitting plug into the groove and check for proper seating.
When using other screw types: Use screws with a head height of max. 2.8 mm,
e.g. screws according to DIN 7996.
Strip insulation of the connection cable as close as possible to the seal cap (see arrow). The stripped part of the connection cable may not be behind the seal cap as this does not guarantee a functional seal.
Insert the modules into the function carrier (observe TOP marking) and lock
(slot screwdriver 4 x 0.8 mm).
For detailed information on the module please refer to the operating
instructions of the individual modules.
Attach the terminating resistors first, followed by the system cable. Always connect a terminating resistors to the first and last module on the system cable.
Trim connection cable to length and connect to plug terminal (A). Rotate plug
terminal by 180° (B) and attach to the connector of the voice module or door
station module.
No jumpers between BUS and ZV No bridges may be laid between BUS and ZV on the
module. The module automatically detects whether an additional power supply is
connected.
Attach safety bond (l: 120 mm).
Swivel the function carriers into the surface-mounted housings (A). Do not
pinch any cables.Pay attention to the position of the line material and the
safety bound!
With 4-gang and 5-gang surface-mounted housings, observe additional snap lock
(B).
Gently tighten the screw to lock the housing using the enclosed locking key
(0,6 Nm).
The application angle is 90°.
Giersiepen GmbH & Co KG
Elektro-Installations-Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 1220
42461 Radevormwald
Tel.: +49 2195 602 – 0
Fax: +49 2195 602 – 191
www.gira.de
info@gira.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>