MOUNTUP MP0006 Triple Monitor Counterbalance Desk Mount Instruction Manual

June 12, 2024
MOUNTUP

MOUNTUP MP0006 Triple Monitor Counterbalance Desk Mount

MOUNTUP MP0006 Triple Monitor Counterbalance Desk
Mount

If you have any questions , please contact our customer service.

WARNING!

**** If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper
installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.

The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

Package Contents

**| DO NOT EXCEED WEIGHT CAPACITY.
**
---|---

ASSEMBLY STEPS

STEP 1 : Clamp Installation OR Grommet Base Installation

OPTION A: Clamp Installation

Loosen Bolts (B5) by using 6mm Allen Key (N), then lift clip plate (B2), bottom plate (B3), and bolt Y (B4) a little to release them from bracket (B1).
Assembly Steps

Mount bracket (B1) to pole(F) using bolts (I). Tighten using 4mm allen key(L).
Attach clip plate(B2), bottom plate(B3), bolt Y(B4), to bracket (B1) using bolts (B5) and 6mm allen key (N).
Mount according to the thickness of desktop.
Assembly Steps

Decorative cover (C) to pole(F) and secure stand to desktop by tightening clamp (B). Tighten bolt Y (B4) or by using 6mm allen key (N).
Assembly Steps

OPTION B: Grommet Base Installation
Use 6mm allen key(N) to detach the bolt(B5), clip plate(B2),bottom plate(B3) and bolt Y(B4) from clamp(B).
Assembly Steps

Install the grommet base plate(K) to the pole (F) using bolt (I).
Install pole(F) with bolt Y(B4) and support plate(J). Tighten bolt Y (B4) or by using 6mm allen key (N).

Assembly Steps

STEP 2 : Arm Installation

Install the middle head(E), wire clip(G) and swivel arm(A) to the pole.
Fasten the bolt with supplied 6mm Allen key (N)
Arm Installation
Assembly Steps

STEP 3: Attach Monitor

OPTION A: Flat Back Monitor

Attach the VESA plate (D) to the back of monitor and secure it by using a 6 mm Allen Key (N) to tighten screws (M-A).

Assembly Steps

Do not tighten the screws excessively or your monitor might be damaged.
Assembly Steps

OPTION B: Curved Back Monitor

Assembly Steps

Attach the VESA plate (D) to the back of monitor and secure it by using a 6 mm Allen Key (N) to tighten screws (M-B) along with spacers (M-C).

Do not tighten the screws excessively or your monitor might be damaged.
Assembly Steps

STEP 4 : Hang Monitor

Slide the monitors onto the head of swivel arm. Install the security bolt (H). Make sure the security bolt is installed before you rotate the monitor.
Assembly Steps

Guideline to adjust monitor tilting angle.

Assembly Steps

Problem:
If monitor face down

Solution:

  1. Loosen the tilting bolt.
  2. Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
  3. Retighten the tilting bolt to fix the intended angle.
STEP 5 : Adjust Tension

For intended functioning of the mount, you may need to adjust the tension of Upper Arm (A) in accordance with your monitor weight by 6 mm Allen Key (N).
Assembly Steps

Situation 1: Arm falls downSituation 1: Arm falls down

Upper Arm with monitor falls down and fails to stay where intended.

Adjust Tension

Solution:
Upper Arm with monitor falls down and fails to stay where intended.
Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.

Situation 2: Arm rises upSituation 2: Arm rises up

Upper Arm with monitor rises up and fails to stay where intended.

Solution:

Turn the inside screw clockwise(“-”direction) to decrease gas spring tension until the arm can stay as intended.

Adjust Tension

Note 2:

For how many circles the screw should be turned, please refer to the table below.

Monitor Weight 1kg 2kg 3kg 4kg 5kg 6kg 7kg 8kg
Circles (AT LEAST) Min 1 2 5 7 10 13 15
STEP 6 : Cable Management

Remove bottom plastic covers from gas spring arm (A) .Run cables from monitor through bottom of arm.  Reattach plastic covers as shown in diagram.
Store Allen keys (M,N) in wire clip (G) for future use.

Cable Management

Adjust as Desired

Adjust monitor position and rotation.

Adjust as Desired

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate

Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously.
If that doesn’t work out, please do not hesitate to ask for our help.

Note: The total length of 3 monitors after arrayed can not be longer than 183cm.

Adjust as Desired

If necessary, refer to above illustrations to adjust the level of tightness of the arms.

Product Dimensions

Product Dimension

CAUTION AND MAINTENANCE

  • Don’t allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals