MOUNTUP MU0037 Height Adjustable TV Wall Mount Instruction Manual
- June 12, 2024
- MOUNTUP
Table of Contents
- MOUNTUP MU0037 Height Adjustable TV Wall Mount
- Product Information
- Product Usage Instructions
- INSTALLATION INSTRUCTION
- Hardware Included
- Step 1-1 Select TV screw diameter
- Step 2 Mesure your TV Pattern
- Step 4A Wall plate installation (Wood Stud)
- Step 5 Lift and Hang TV with Brackets onto Wall Bracket
- Adjustments
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MOUNTUP MU0037 Height Adjustable TV Wall Mount
Product Information
This product is a TV wall mount designed for use in wood stud or solid concrete walls. It should not be installed into drywall alone. The wall must be capable of supporting five times the weight of the TV and mount combined to ensure proper installation and prevent product damage or body injury.
It is important to note that this product contains small items that could pose a choking hazard if swallowed.
Before starting the assembly, please verify that all parts are included and undamaged. If there are any parts shortages or damages, please contact us for assistance.
Product Usage Instructions
- Read the installation instructions carefully before proceeding with the installation.
- Ensure that the wall where the TV mount will be installed is a wood stud or solid concrete wall. Do not install into drywall alone.
- Check if the wall is capable of supporting five times the weight of the TV and mount combined.
- Inspect all parts included in the package to ensure they are present and undamaged.
- If there are any parts shortages or damages, contact us for assistance.
- Start the assembly by attaching the upper arm to the TV plate using the provided wrench.
- Attach the extenders to the upper arm using screws 3A and 3B.
- Attach the wall plate cover to the extenders using screws 04.
- Make sure to tighten all screws securely.
- Before mounting the TV, check the maximum distance specified on the TV plate (MAX:400mm/16) and ensure your TV is compatible with this mount.
- Follow your TV manufacturer’s instructions to mount the TV onto the TV plate.
If you have any doubts about the safety of the installation, assembly, or use of this product, please contact us for further guidance and assistance.
INSTALLATION INSTRUCTION
- Max: 600x400mm/24×16″
- Min: 200x100mm/8×4
If you have any questions, please feel free to contact us via Amazon.
Warm Tips
You could also refer to the Video Guide about installation on our product
page.
Safety Caution
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of
the installation, assembly or use of this product, please contact us.
- This product is designed for use in wood stud or solid concrete wall.
- DO NOT install into drywall alone.
- The wall must be capable of supporting five times the weight of the TV and mount combined.
- Incorrect installation may result in product damage or body injury.
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage, please contact us.
Must Check Before Getting Started
Installation Tools (Not Included)
Hardware Included
TV Screws / Washers
Step 1-1 Select TV screw diameter
Thread screws by hand into the threaded holes on the back of your TV to select which screw diameter fits your TV.
Step 1-2 Select TV screw length
When attaching brackets to the flat screen, be careful not to over tighten
screws and be sure that screws do not bottom out in the mounting holes
.
Step 2 Mesure your TV Pattern
Measure and note the width and the height of the square or rectangle formed from the VESA holes pattern
- 100mm ≈ 4in.
- 130mm≈ 5 1/8in.
- 200mm ≈ 8in.
- 300mm ≈ 11 3/4in
- 340mm ≈ 13 3/4in.
- 400mm≈ 16in.
Step 3-1 Select TV Plate Configuration
Select the configuration A , B , C, D, or E to use based on the measurement
from Step 2.
VESA
(WxH)
| Configuration| VESA
(WxH)
| Configuration
---|---|---|---
100mm x 100mm| A| 300mm x 200mm| C
130mm x 130mm| A| 300mm x 300mm| E
200mm x 100mm| A| 400mm x 200mm| C
200mm x 200mm| A| 400mm x 300mm| D
200mm x 300mm| B| 400mm x 400mm| E
200mm x 400mm| B| |
For VESA: 100x100mm, 130x130mm,200x100mm, 200x200mm
Step 3-2 Assemble TV Plate and Extenders
If your TV hole pattern is greater than 200x200mm, attach extenders [3A] and
[3B] to TV plate [02] using Nut [4A] and Bolt [4B].
Step 3-3 Attach the TV Plate
- For Flat Back
- For Round Back / Extra Space
Step 4A Wall plate installation (Wood Stud)
Locate your studs. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge-to-edge stud finder.
Position the upper arm at your desired01 height and line up the holes with your stud center line. Level the wall plate and mark the pilot hole locations x2.
Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2 3/4 in (70 mm). Be sure to drill into the center of the stud.
Install wall plate 01 using lag bolts A with Socket Wrench, NO Electro drill.
Tighten the lag bolts A until they are pulled firmly against the wall plate 0
1 .
Step 4B Wall plate installation (concrete or brick)
Position the wall plate 0 1 at your desired height , level the wall plate and mark the pilot hole locations x2
B-3 Install wall plate 01 using lag bolts A and anchors (not included) with Socket Wrench, NO Electrodrill. Tighten the lag bolts untilA they are pulled firmly against 0the wall plate . Tighten the1 Alag bolts until they are pulled firmly against the wall plate 01 .
Concrete wall anchor 2pcs (NOT INCLUDED)
Contact us to have these additional pieces shipped directly to you.
Step 5 Lift and Hang TV with Brackets onto Wall Bracket
- Remove 2 preassembled screws and washers before hang TV on to the wall bracket, and save them for using to next step.
- Lift and hang TV assembly onto arm and wall plate.
- Secure the TV plate to the arm and wall plate with the removed screws and washers from the previous step.
STEP 6 Adjust Gas Spring Tension
For proper functioning of this mount, You might need to adjust tension in
upper arm depending on different weight of TV.
Situation 1: Arm falls down
Upper Arm with TV falls down and fails to stay where intended. Solution: Turn
the inside screw clockwise(“+”direction) to increase gas spring tension till
the arm can stay as intended.
Situation 2: Arm rises up
Upper Arm with TV rises up and fails to stay where intended. Solution: Turn
the inside screw counterclockwise(“-”direction) to decrease gas spring tension
till the arm can stay as intended.
Adjustments
(Tilting Adjustment)
(Tilting)
Tilting Angle Adjustment (+5° / -15°) Loosen 2 tilting bolts, pull TV to your
desired angle, then fasten tilting nuts with open-end wrench.
(Leveling) Leveling adjustment (-3°/+3°)
If needed, TV can be leveled ±3 degrees via adjusting the 2 screws with the
open end wrench.
Cable Management
Product Dimensions:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>