MOUNTUP MP0001 Single Monitor Desk Mount Instruction Manual

June 12, 2024
MOUNTUP

MOUNTUP logo

Single Monitor Desk Mount
Instruction ManualMOUNTUP MP0001 Single Monitor Desk
MountMOUNTUP MP0001 Single Monitor Desk Mount -
icon MS-03N-US2.0
If you have any questions, please feel free to contact us via Amazon.

Must Check Before Installation

  1. Is your monitor VESA 75×75mm/3×3″ or 100×100mm/4×4″? MOUNTUP MP0001 Single Monitor Desk Mount - assembly 1Yes — Perfect!
    No — This mount is NOT compatible.

  2. Is the weight of your monitor (including accessories) less than 19.8lbs (9kg)? Yes — Perfect!
    No — This mount is NOT compatible.

  3. Is your desk thickness 10~50mm (0.39~1.97”)?
    MOUNTUP MP0001 Single Monitor Desk Mount - assembly 3Yes — Perfect!
    No — This mount is NOT compatible.

If this mount is NOT compatible, please contact our customer service to nd a compatible mount.
WARNING!
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Supplied Parts List

MOUNTUP MP0001 Single Monitor Desk Mount - Parts List NOTE: Not all hardware included will be used.

ASSEMBLY STEPS

Warm Tips
You could also refer to the Video Guide about installation on our product page.
STEP 1: Apply Pad to the Pole Bottom
Apply pad (e) to the Pole (a) bottom to avoid desk scratches.MOUNTUP MP0001
Single Monitor Desk Mount - Parts List STEP 2: Clamp Installation OR Grommet Base Installation
OPTION A: Clamp Installation

  1. Mount Clamp (d) to the bottom of Pole (a) by tightening bolts (B) with 5mm Allen Key (G).
  2. Adjust the Clamp width to fit your desk. Secure stand to the desktop by tightening Clamp (d).

MOUNTUP MP0001 Single Monitor Desk Mount - assembly 5 OPTION B: Grommet Base Installation

  1. If existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount.
  2. Detach Bracket (d1) and Bolt Y (d2) from Clamp (d).MOUNTUP MP0001 Single Monitor Desk Mount - assembly 6
  3. Position pole (a) on the mounting surface and then secure it by tightening the plastic knob after making Bolt Y (d2) through the Bracket (d1), desk hole, and the bottom of Pole (a) sequentially.MOUNTUP MP0001 Single Monitor Desk Mount - assembly 7

STEP 3: Install Arm to the Pole

  1. Install Wire Clip (F1) and Swivel Arm (b) to the Pole (a).MOUNTUP MP0001 Single Monitor Desk Mount - assembly 8
  2. Fasten the bolt with supplied Allen Key (G 6mm).
  3. Attach the Wire Clip (F2) to the Swivel Arm (b).

MOUNTUP MP0001 Single Monitor Desk Mount - assembly 9

Please do not move stand outside desk for safety!

STEP 4: Attach the VESA Plate to the Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (c) to the monitor with M4×12 bolts (D).
NOTE: Hand tighten screws to avoid over tightening.MOUNTUP MP0001
Single Monitor Desk Mount - assembly 10 OPTION B: Curved or Recessed Back Monitor
Attach the VESA plate (c) to the monitor with M4×30 bolts (C) and M4 spacers (E).
NOTE: Hand tighten screws to avoid over tightening.MOUNTUP MP0001
Single Monitor Desk Mount - assembly 11 STEP 5: Slide the Monitor onto the Head of Swivel Arm
Slide the monitor onto the head of Swivel Arm (b) as shown in diagram.MOUNTUP MP0001 Single Monitor Desk Mount - assembly
12Install the security Bolt (A). Make sure the security Bolt is installed before you rotate the monitor.MOUNTUP MP0001
Single Monitor Desk Mount - assembly 13 STEP 6: Make the Necessary Adjustments
Fix the tilt angle
Tighten the bolt with the supplied Allen Key (G 5mm) to fix the tilt angle.MOUNTUP MP0001 Single Monitor Desk Mount - assembly
14 Note: W hen tilted, if the monitor sags or does not stay, and if the above method is useless, please feel free to contact our customer service.
Fix the swivel angle
Use the supplied Allen Key (G 5mm) to make the necessary adjustments. Ignore this step if the arm joint has screwed to the proper tightness.
MOUNTUP MP0001 Single Monitor Desk Mount - assembly 15 STEP 7: Manage the Wires
Manage the wires and store the Allen keys (G 6mm, G 5mm, G 3mm) in Wire Clip (F1) for future use.MOUNTUP MP0001 Single Monitor Desk Mount - assembly
16

Product Dimensions

MOUNTUP MP0001 Single Monitor Desk Mount - Product
Dimensions

**** CAUTION AND MAINTENANCE:

  • Never allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).

MOUNTUP logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals