AcuityBrands P6300 Trac Adapter Installation Guide
- June 12, 2024
- AcuityBrands
Table of Contents
AcuityBrands P6300 Trac Adapter
Product Information
Before installing the Juno Trac Adapter, please read all of the following installation instructions carefully. Remember to save these instructions for future reference.
Fixture Installation
- Step 1: Find the latch and the polarity line. Align the parts as shown in Figure 1 and insert the adapter box into the track.
- Step 2: Pull down the latch while rotating the adapter box 90 degrees clockwise, as shown in Figure 2.
- Step 3: The final position should have the latch snapped into place between the extrusion rails. The arrows on the latch should be pointing toward the polarity line, as shown in Figure 3.
Second Circuit Positioning
- Step 1: Raise the contact marked P (on switch side) by inserting a thin screwdriver blade under the contact. Pull it up into position as shown in Figure 4.
- Step 2: Insert the contact support (supplied with the 2-circuit Trac section) by tilting and snapping it into position under the P contact, as shown in Figure 5.
- Step 3: Ensure that the contact support is snapped and locked into position, as shown in Figure 6. Follow the instructions for inserting it into the track.
Troubleshooting
- Problem: The fixture doesn’t turn on
- Cause: Track not energized
- Remedy: Ensure the track has power.
- Problem: The adapter switch is in the Off position
- Remedy: Ensure the power switch on the track fixture adapter is in the On position, as shown in Figure 9.
- Problem: Fixture installed incorrectly
- Remedy: Ensure the fixture is installed correctly, with the arrows on the latch pointing toward the polarity line as shown in Figure 3.
- Problem: Contacts aren’t bent from installing the fixture incorrectly
- Remedy: Ensure contacts aren’t bent from adjusting incorrectly, as shown in Figure 7.
- Problem: P contact adjusted incorrectly
- Remedy: Ensure the P contact isn’t bent from adjusting incorrectly, as shown in Figure 8.
Note: The Juno Trac adapter size and style may vary.
FIXTURE INSTALLATION
- Step 1 Find the latch and the polarity line. Align parts as shown and insert the adapter box into the track. (Fig. 1) |
- Step 2 Pull down the latch while rotating the adapter box 90 degrees clockwise. (Fig. 2)
Step 3 Final Position: Latch snaps into place between extrusion rails. Arrows on latch point toward the polarity line. (Fig. 3)
SECOND CIRCUIT POSITIONING
- Step 1 Raise the contact marked “P” (on switch side) by inserting a thin screwdriver blade under contact. Pull up into position as shown. (Fig. 4)
-
- Step 2 Insert contact support (supplied with 2-circuit Trac section) by tilting and snapping into position under the “P” contact as shown. (Fig. 5)
- Step 3 Ensure contact support is snapped and locked into position. (Fig. 6) Follow instructions for inserting into track.
TROUBLESHOOTING
| Problem | Cause | Remedy |
|---|
Fixture doesn’t turn on
| Track not energized| Ensure track has power
Adapter switch is in the “Off” position| Ensure the power switch on the track
fixture adapter is in the “On” position, see Fig. 9
Fixture installed incorrectly
| Ensure fixture is installed correctly, with the arrows on the latch pointing
towards the polarity line as shown in Fig. 3
Ensure contacts aren’t bent from installing the fixture incorrectly, see Fig.
7
“P” Contact adjusted incorrectly
| Ensure “P” contact isn’t bent from adjusting incorrectly, see Fig. 8
Bent contact from adjusting the wrong contact, see Fig. 4, 5, & 6 for proper
adjustment method
- One Lithonia Way
- Conyers, GA 30012
- 1-800-705-SERV (7378)
- www.acuitybrands.com
©.2020 Acuity Brands Lighting, Inc. P6300 Rev 10/2022
WARNING: Read all of these installation instructions before installing.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>