Go Power GP-ADV-LiFePO4-300 Advanced Lithium Battery User Guide

June 12, 2024
Go Power

Go-Power-LOGO

Go Power GP-ADV-LiFePO4-300 Advanced Lithium Battery

Go-Power-GP-ADV-LiFePO4-300-Advanced-Lithium-Battery-PRODUCT-
IMAGE

SPECIFICATIONS

Technology Lithium Iron Phosphate
Nominal Voltage 12.8 V
Fully Charged Voltage (FC) 14.6V
Fully Discharged Voltage (FD) 9.2V
Capacity (Ah) 300Ah
Recommended Discharge Terminated Voltage 10V
Battery Discharge Terminated Voltage 9.2V
Battery Charge Voltage 14.2V
Max Continuous Charge Current 200A

Heater Function

| Battery pack includes heater for heating cell module temperature up when battery pack is charged in a freezing environment


Standard Charge Method

| 0.2C CC (constant current) charge to FC, then

CV (constant voltage FC) charge till charge current decline to $0.05C

Inner Resistance| $10mO
Certifications| ETL, CE, UKCA, UN38.3, UL 2054


Operating Temperature

| Charge: -4°F (-20°C) to 131°F (55°C)

Discharge: -4°F (-20°C) to 131°F (55°C)


Storage Temperature1

| 1 month> 113°F (45°() to 131°F (55°C) – Max 80% RH
3 months> 77°F (25°C) to 113°F (45°() – Max 80% RH
6 months> -4°F (-20°C) to 77°F (25°C) – Max 80% RH


Humidity

| Operating: 5% to 90 % RH

Storage: 45% to 85% RH

BMS Leakage Current| 20uA in Shutdown Mode
IP Requirement| IP67
Dimensions (LxWxH)| 19.6in x 14.9in x 8.11in (498mm x 379mm x 206mm)
Weight| 70.5Ibs (32kg)

Go-Power-GP-ADV-LiFePO4-300-Advanced-Lithium-
Battery-01

WARNINGS

  • Only wire 8 batteries maximum in parallel
  • Wire a maximum of 4 in series
  • Do not get wet

INTERFACE DESCRIPTION LED (POWER BUTTON) INDICATORS

Go-Power-GP-ADV-LiFePO4-300-Advanced-Lithium-
Battery-02

VARIOUS POWER MODES
Press button for more than 3 seconds and release. The battery will enter sleep mode. The LED will blink. Power off mode should only be used for long term storage or to reset the BMS. Use sleep mode to disable output power of batteries.

Go-Power-GP-ADV-LiFePO4-300-Advanced-Lithium-
Battery-03

MOBILE APP 8
Scan the QR code to download the Go Power! Connect App for use with the Sun Cycle® Advanced Lithium Battery.

BATTERY WIRING
*cables purchased separately

Go-Power-GP-ADV-LiFePO4-300-Advanced-Lithium-
Battery-05

HOW TOUSE
To prevent a surge current, perform a “pre-discharge” as outlined in the steps below.

  • Step 1 – Ensure all batteries are in Power Off mode.

  • Step 2 – Connect batteries following the series or parallel connection found at gopowersolar.com/advanced-lithium-wiring. The Battery Inter-Connect Cable must be installed for each battery pack followed by a Battery End Cap Terminating Resistor cable on the last battery.

  • Step 3 – Ensure battery pack terminals are correctly installed and connected to
    the inverter system.

  • Step 4 – Press the power button on one of the battery packs for 3 seconds to wake up all battery packs from Power Off mode. The LED indicator will turn on.

NOTE: Batteries are in Power Off mode when unboxed. Press the Power button for 3 seconds to turn on. If it doesn’t turn on, you will need to charge the battery.
The batteries need to be configured before they can be used. Please see battery manual for instructions on battery configuration.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals