Yealink BHM711 Bluetooth Headset Workstation User Guide
- June 12, 2024
- Yealink
Table of Contents
BHM711 Bluetooth Headset Workstation
User Guide
Bluetooth Headset
BH71 Workstation/BH71 Workstation Pro
www.yealink.com
BH71 Workstation
BH71 Workstation Pro
Charge Headset
It takes approximately 90 minutes to fully charge the headset.
Charging Indicator
• Charging Case Charging: Flash green
Charging is complete: Off
• Station
Charging: Solid green
Charging is complete: Off
Power on/off
Connect Your Devices
The USB hub is an extension port of the PC. After the station is connected to the PC, you can plug a USB driver into the USB hub port, or plug the phone and charging case into the USB hub port for charging.
Connect the desk phone, PC or busylight to station.
Pair Your Devices
• Pair your station
– Tap Bluetooth->Settings in the station.
– Enable Open discover.
A Pair with headset
Place the headset on the station and the headset will automatically pair with
the station.
B Pair with phone
Note: One headset or station can only
connect to two devices at a time.
• Pair your headset
Slide and hold the switch for 3 seconds until the LED indicator flashes red
and blue automatically.
A Pair with phone 
B Pair with PC（BH71 Workstation Pro） 
The BT51A is pre-
paired to the headset and ready for use.
Note: The BT51A can only connect to a device at a time.
Fit the Headset
Right ear wearing
- Take out the headset, as shown in figure ❶ . Twist the speaker to the left, and then rotate microphone boom down.
Before wearing, you can adjust the height of the speaker up or down to get the perfect fit for your ear.
- Put the eartip in your ear and slide headset over and behind your ear, then press gently toward your ear. Fine-tune the headset according to your own situation.
Left ear wearing
- Take out the headset, as shown in figure ❶. Twist the speaker to the right, and then rotate microphone boom down.
- For wearing methods, please refer to steps 2 and 3 of the right ear wearing.
Note:
Remove your eyeglasses before donning the headset for best fit.
Change the eartip for a better fit. Eartips with three size options — S/M/L
(medium pre-installed).
Call Control
Software Management
Download it from the Yealink website https://www.yealink.com/product/yuc.
Note: It needs to
be used with Yealink USB Connect of version 0.35.x.x or later.
NEED MORE HELP?
| 
---|---
Technical support https://ticket.yealink.com |
FAQ & User manual http://support.yealink.com
Safety Guide
- Do not disassemble the product by yourself or bring it near fire and water to avoid short circuit leakage or damage to the product.
- Do not use the product in high temperature, humidity, and corrosive environment to avoid damaging the circuit and causing failure to charge or other failures.
- Do not expose the product to corrosive liquids. Otherwise, it will cause severe damage.
- Do not disassemble or re-equip the product for any reason to avoid secondary failure and burnout.
- Do not place the product in an environment below -10°C or above 60°C.
- Do not knock, throw or shake the product because rough methods will damage the internal circuit board structure.
If your headset needs warranty service, the process is quick and easy. Please
go to https://ticket.yealink.com/page/headset/warranty-service.html and
submit RMA Claim to Yealink.
Regulatory Notices
Operating Ambient Temperatures
- Operating temperature: 0 °C to +40 °C (+32 °F to +104°F)
- Relative humidity: 5% to 90%, noncondensing
- Storage temperature:-30°C to +70°C (-22 to +158°F)
Warranty
Our product warranty is limited only to the unit itself, when used normally in
accordance with the operating instructions and the system environment. We are
not liable for damage or loss resulting from the use of this product, or for
any c laim from a third party. We are not liable for problems with Yealink
device arising from the use of this product; we are not liable for financial
damages, lost p rofits, claims from third parties, etc., arising from the use
of this product.
Explanation of the symbols
- DC symbol **** is the DC voltage symbol.
- WEEE Warning symbol
To avoid the potential effects on the environment and human health as a result
of the presence of hazardous substances in ele ctrical and electronic
equipment, end users of electrical and electronic equipment should understand
the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste and have to collect such WEEE separately.
Restriction of Hazardous Substances Directive (RoHS)
This device complies with the requirements of the EU RoHS Directive.
Statements of compliance can be obtained by contacting
support@yealink.com.
Safety Instructions
Save these instructions. Read these safety instructions before use!
General Requirements
- Before you install and use the device, read the safety instructions carefully and observe the situation during operation.
- During the process of storage, transportation, and operation, please always keep the device dry and clean, avoid collision and crash.
- Please attempt not to dismantle the device by yourself. In case of any discrepancy, please contact the appointed maintenance center for repair.
- Please refer to the relevant laws and statutes while using the device. Legal rights of others should be respected as well.
Environmental Requirements
- Place the device at a well-ventilated place. Do not expose the device under direct sunlight.
- Keep the device dry and free of dust.
- Do not place the device on or near any inflammable or fire-vulnerable object, such as rubber-made materials.
- Keep the device away from any heat source or bare fire, such as a candle or an electric heater.
Operating Requirements
- Do not let a child operate the device without guidance.
- Do not let a child play with the device or any accessory in case of accidental swallowing.
- Please use the accessories provided or authorized by the manufacturer only.
- The power supply of the device shall meet the requirements of the input voltage of the device. Please use the provided surge protection power socket only.
- Before plugging or unplugging any cable, make sure that your hands are completely dry.
- Do not spill liquid of any kind on the product or use the equipment near water, for example, near a bathtub, washbowl, kitche nsink, wet stationment or near a swimming pool.
- During a thunderstorm, stop using the device and disconnect it from the power supply. Unplug the power plug and the Asymmetric Digital Subscriber Line (ADSL) twisted pair (the radio frequency cable) to avoid lightning strike.
- If the device is left unused for a rather long time, disconnect it from the power supply and unplug the power plug.
- When there is smoke emitted from the device, or some abnormal noise or smell, disconnect the device from the power supply, and unplug the power plug immediately.
- Contact the specified maintenance center for repair.
- Do not insert any object into equipment slots that is not part of the product or auxiliary product.
- Before connecting a cable, connect the grounding cable of the device first. Do not disconnect the grounding cable until you disconnect all other cables.
Battery Requirements
- Do not immerse the battery into water, which could short-circuit and damage the battery.
- Do not expose the battery to an open flame or leave the battery where it could be subjected to extremely high temperatures, which could cause the battery to explode.
- Do power the handset off before removing the battery.
- Do not try to use the battery for the power supply of any device other than this handset.
- Do not open or mutilate the battery, released electrolyte is corrosive and may cause damage to your eyes or skin.
- Use only the rechargeable battery pack delivered with the handset or those rechargeable battery packs expressly recommended by Yealink.
- Defective or exhausted battery should never be disposed of as municipal waste. Return old battery to the battery s upplier, a licensed battery dealer or a designated collection facility.
Cleaning Requirements
- Before cleaning the device, disconnect it from the power supply.
- Use a piece of soft, dry and anti-static cloth to clean the device.
- Keep the power plug clean and dry.
Troubleshooting
The unit cannot supply power to Yealink device.
There is a bad connection with the plug.
- Clean the plug with a dry cloth.
- Connect it to another wall outlet.
The usage environment is out of operating temperature range.
- Use in the operating temperature range.
The cable between the unit and the Yealink device is connected incorrectly.
- Connect the cable correctly.
You cannot connect the cable properly.
- You may have connected a wrong Yealink device.
- Use the correct power supply.
Some dust, etc., may be in the port.
- Clean the port.
Contact your dealer or authorized service facility for any further questions.
FCC CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
The BHB710 Station should be installed and operated with minimum distance 20cm
between the radiator& your body.
ISED WARNING
This device complies with Innovation, Science and Economic Development Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Cetappareilnumérique de la classe B estconformeà la norme NMB-003 du Canada.
The device is compliance with RF exposure guidelines, users can obtain
Canadian information on RF exposure and compliance. For BHB710 Station, the
minimum distance from body to use the device is 20cm.
EU regulations
Supported frequency bands and power:
Bluetooth 2.4GHz <20dBm contact information
YEALINK NETWORK TECHNOLOGY CO.,LTD.
No.666 Hu’an Rd. Huli District Xiamen City, Fujian, P.R. China
YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.
Strawinskylaan 3127, Atrium Building, 8th floor, 1077ZX
Amsterdam, The Netherlands
YEALINK (USA) NETWORK TECHNOLOGY CO., LTD.
999 Peachtree Street Suite 2300, Fulton, Atlanta, GA, 30309, USA
Made in China
YEALINK (XIAMEN) NETWORK TECHNOLOGY CO.,LTD
WWW.YEALINK.COM
Declaration of Conformity
We,
YEALINK(XIAMEI\) NETWORK TECHNOLOOY CO.,LTD
Address: No.666 Hu’an Rd. Huli District Xiamen City, Fujian, P.R. China
Manufacturer: YEALINK(X!AMEl\) NETWORK TECHNOLOGY CO.,LTD
Address: No.666 Hu’an Rd. HL1li District Xiamen City, Fujian, P.R. China
DATE: 28th /November/ 2022 declare that the product Type:
Bluetooth Headset Model:
BHB710 meets the essential requirements and other relevant provisions
according to the following EC directive
Directive: 2014/30/EU, 2014/35/EU, RED 2014/53/EU Conformity
The product complies with the following standards:
Safety: EN IEC 62368-1:2020+A11:2020
EMC: EN 55032:2015+A1:2020
EN 55035:2017+A11:2020
EN IEC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A2:2021
ETSI EN 301489-1 VZ.2.3 (2019-11)
ETSI EN 301489-3 VZ.2.2 (2021-11)
ETSI EN 301 489-17 V3.2.4 (2020-09)
Radio: ETSI EN 300 328 V2.2.2 (2019-07)
ETSI EN 303 417 Vt.1.1 (2017·09)
Health: EN 624 79:2010; EN 50663:2017
Directive 2011/65/EU and (EU] 2015/863 of the European Parliamentand of the
Council of8 June 2011 and 4 June 2015 on the restriction of the use of certain
hazardous substances in electrical and electronic equipment(RoHS2.0)
Directive 2012/19/EU of the European Parliamentand of the Council of
4.July.2012 on Waste electrical and electronic equipment(WEEE)
Regulation (EC) No.1907/2006 of the European Parliamcntand of the Council of
18.Dcccmbcr.2006 on Registration, Evaluation, Authorization, and Restriction
of Chemicals (REACH)
NAME: Hu ahu Wang f(w,,fv.,, lf\)i:.,,,_
DATE: 22/v•v/ 2,J-,, v
TITLE: Manager
De claration of Conformity
We,
YEALINK(XIAMEN) NETWORK TECH”‘\./OLOGY CO.,LTD
Address: No.666 Hu’an Rd. H111i Oistl’ict Xiamen City, Fujian, P.R. China
Manufacturer: YEAUNK(XIAMEN) NJ:::’J’WORK ‘!’ECHNOLOGY CO.,LTD
Address: No.666 Hu’an Rd. Huli District Xia.men City, Fujian, P.R. China
DATE: 28th/November/2022 declare that the product Type:
Charging Case
Model: BHC71P
meets the essential requirements and other relevant provisions according to
the following EC directive Directive: 2014/30/EU, 2014/35/EU
Conformity
The product complies with the following standards:
Safety:EN !EC 62368·1:2020+A11:2020
EMC: EN 55032:2015+Al:2020
EN 55035:2017+A11:2020
EN IEC 61000-3-2:2019+A1:2021
EN 61000·3-3:2013+A2:2021
Directive 2011/65/EU and (EU) 2015/863 of the European Parliamentand of the
Council of 8 June 2011 and 4 June 2015 on the restriction of the use of
certain hazardous substances in electrical and electronic equipment(RoHSZ.0)
Directive 2012/19/EU of the European Parliamentand of the Council of
4.July.2012 on Waste electrical and electronic equipment (WEEE)
Regulation (EC) No.1907/2006ofthe European Parliamentand of the Council of
18.December.2006 on Registration, Evaluation, Authorization, and Restriction
of Chemicals (REACH)
NAME: Huahu Wang
DATE,
TITLE: Manager
De claration of Conformity
We,
YEALINK(X!Alv!E’l) NETWORK TECIINOLOGY CO.,LTD
Address: No.666 Hu’an Rd. Huli District Xiamen Cily, Fujian, P.R. China
Manufacturer: YEALINK(XIAME ) NETWORK TECHKOLOGY CO.,LTD
Address: No.666 Hu’an Rd. Huli Distl”ict Xiamen City, Fujian, P.R. China
DATE: 28th/November/2022 declare that the product Type:
Bluetooth Headset Model: BHM711
meets the essential requirements and other relevant provisions according to
the following EC directive Directive: 2014/30/EU, 2014/35/EU, RED 2014/53/EU
Conformity
The product complies with the following standards:
Safety: EN !EC 62368-1:2020+A11:2020
EMC: EN 55032:2015+A1:2020
EN 55035:2017+A11:2020
EN !EC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A2:2021
ETSI EN 301 489-1 V2.2.3 (2019-11)
ETSI EN 301489-17 V3.2.4 (2020-09)
Radio: ETSI EN 300 328 V2.2.2 (2019-07)
Health: EN 62479:2010; EN50663:2017
Directive 2011/65/EU and (EU) 2015/863 of the European Parliamentand of the
Council of8 June 2011 and 4 June 2015 on the restriction of the use of certain
hazardous substances in electrical and electronic equipment(RoHSZ.01
Directive 2012/19/EUofthe European Parliamentand of the Council of 4.July.2012
on Waste electrical and electronic equipment (WEEE)
Regulation (EC) No.1907/2006ofthe European Parliamentand of the Council of
18.December.2006 on Registration, Evalualion, Authorization, and Restriction
of Chemicals (REACH)
NAME, DATE,
Huahu Wang
TITLE, Manager
Addr 309, 3rd Fkxlr, No 16, Yun Ding North Road,
Hui District X1amen Otv Fu11an PR China
Tel +86 592 57C2000
Fax +86 592 5702455 Model: BHM711
Input :5V ****0.2A
Bluetooth Headset
FCC ID：T2C-BHM711
IC：10741A-BHM711
References
- Yealink Support
- Yealink Support
- Yealink | UC & C Terminal, Video Collaboration, Conference Phone, IP Phone, Headsets & Video Conferencing
- USB Connect | Yealink
- Yealink | UC & C Terminal, Video Collaboration, Conference Phone, IP Phone, Headsets & Video Conferencing
- Yealink Ticket
- Yealink Ticket
- Yealink | UC & C Terminal, Video Collaboration, Conference Phone, IP Phone, Headsets & Video Conferencing
- USB Connect | Yealink
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>