EUFAB 21084 Dual Power Compressor Instruction Manual
- June 12, 2024
- EUFAB
Table of Contents
- EUFAB 21084 Dual Power Compressor
- Product Information
- Product Usage Instructions
- PROPER USE OF THE PRODUCT
- SCOPE OF DELIVERY
- SPECIFICATIONS
- SAFETY PRECAUTIONS
- EXPLANATIONS OF SYMBOLS
- OPERATING INSTRUCTIONS
- TROUBLESHOOTING
- MAINTENANCE AND CARE
- NOTES REGARDING ENVIRONMENTAL PROTECTION
- CONTACT INFORMATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EUFAB 21084 Dual Power Compressor
Product Information
- Product Name: DUAL POWER COMPRESSOR 12 V / 230 V
- Product Code: 21084
- Input Voltage: 230 V 50 Hz, AC / 12 V, DC
- Max Pressure: 10.3 bar / 150 psi
- Max Power: 120 W
- Dimensions: Approximately 22 x 13 x 7.5 cm
Product Usage Instructions
- Read the operating instructions carefully before using the product.
- Check the contents of the package for integrity and completeness before use.
- This dual power compressor is designed for universal use, including pumping car, motorbike, and bicycle tires, sport balls, and inflatable toys.
- Connecting the Compressor:
- Attach the valve connector to the valve.
- Lock the valve connector in place.
- Presetting the Air Pressure:
- Use the (-) button to select the desired pressure unit.
- Refer to the provided table to set the desired pressure level.
- Filling a Tyre Using the Car Valve:
- Follow the steps for connecting the compressor and presetting the air pressure.
- Start the compressor and allow it to fill the tyre until the desired pressure is reached.
- Troubleshooting:
- If the compressor does not work, check if the connection cable is correctly attached.
- In case of using the compressor in a car, ensure there is voltage in the car socket
- If necessary, replace the fuse in the 12 V plug. Refer to section 6.7 for instructions.
- Maintain and clean the product as per the provided instructions.
- Dispose of the product responsibly according to environmental guidelines.
WARNING
- Read the operating instructions through carefully prior to initial use and observe all of the safety notes!
- Not observing such may lead to personal injuries, damages to the device or to your property!
- Store the original packaging, the receipt and these instructions so that they may be consulted at a later date! When passing on the product, please include these operating instructions as well.
- Please check the contents of package for integrity and completeness prior to use!
PROPER USE OF THE PRODUCT
- The dual power compressor is designed for universal use e.g. for pumping car, motorbike and bicycle tyres, sport balls and, infl atable toys.
- It may be connected to the 12 V on-board network of a vehicle or the 230 V household network. The manometer can be used during the fi lling process to monitor the pressure.
- This device is not designed to be used by children or persons with limited mental abilities or without experience and/or lack of required specialist knowledge. Keep children away from the device.
- The device is not designated for commercial use.
- Use according to the intended purpose also includes the observance of all information in these operating instructions, particularly the observance of the safety notes. Any other utilisation is considered to be contrary to the intended purpose and may lead to material damages or personal injuries. EAL GmbH assumes no liability for damages resulting from improper use.
SCOPE OF DELIVERY
- 1 x Dual Power Compressor
- 1 x Car connection cable for 12 V on-board socket
- 1 x Connection cable for 230 V house socket
- 2 x Fuse, fast 15 A 250 V, 6 x 30
- 1 x Adapter ø 5 mm
- 1 x Adapter ø 8 mm
- 1 x Ball adapter
- 1 x Operating instructions
SPECIFICATIONS
- Input voltage: 230 V 50 Hz AC 12 V DC
- Maximum pressure: 1 0.3 bar / 150 psi
- Max. Power: 120 W
- Dimensions (L x W x H) : approx. 22 x 13 x 7.5 [cm]
- Weight (without accessories): approx. 0.950 kg
- Length of air hose: approx. 0.50 m
- Length of 12 V-cable: approx. 3.50 m
- Length of 230 V-cabl: approx. 1.50 m
SAFETY PRECAUTIONS
- The warning symbol indicates all instructions which are important for safety. Always follow these, otherwise you could injure yourself or damage the device.
- Children may not play with the device.
- Cleaning and user maintenance may not be carried out by children without supervision.
- Do not treat packaging material carelessly. This may become a dangerous plaything for a child!
- Only use this product for its designated purpose!
- Do not manipulate or disassemble the device!
- For the objects to be inflated, do not increase the air pressure beyond the recommendations of the manufacturer!
- Protect the compressor and its components from damp!
- Do not leave an operating compressor unattended!
- Keep children away and do not allow children to operate this device!
- Never cover the ventilation slots of the compressor during operation.
- If the compressor emits unusual noises or overheats, switch it off immediately and give it at least 20 minutes to cool down!
- Check the compressor before use. Damaged, cracked or broken components should be repaired only by qualified technicians!
- Never expose the compressor to frost, rain or temperatures above 30°C or below – 30°C!
- Never use on people or animals!
- Make sure that the hose and cable are not exposed to sharp edges, oil or objects that are too hot!
- When filling, always pay attention to the correct air pressure (consult the operating instructions of your vehicle for information). The compressor is able to supply a pressure of up to 10.3 bar. If the pressure is too high, there is a risk of explosion and injury.
- Never allow the compressor to operate for longer than 10 minutes without a pause, otherwise there is a risk of overheating. Switch the compressor off after 10 minutes of use and allow it to cool down fully (at least 20 minutes) before starting it up again.
- The compressor may discharge the battery of your vehicle if the motor is switched off.
- If you use the compressor with the vehicle motor running, ensure good ventilation in the garage or hall. There is a risk of poisoning!
- Separate the compressor from the power supply when it is not in use.
- For your own safety, only use accessories and spare parts that are stated in these instructions or that are recommended by the manufacturer!
EXPLANATIONS OF SYMBOLS
Complies with EC directives
- Labelled electrical products may not be disposed of in the household waste
- Devices with this symbol may only be operated indoors (dry environment)
- Insulated housing (protection class II).
- Read the operating instructions
OPERATING INSTRUCTIONS
OVERVIEW
- ON / OFF switch
- Switch for LED work light
- Display with setting buttons
- 12 V input
- 230 V input
- LED work light
- Air hose with autovalve
- (+) button
- (R) button for setting units
- (-) button
- Unit for pressure
- Pressure indicator
- 12 V car connection cable
- 230 V connection cable
- Ball adapter
- Adapter Ø 8 mm
- Adapter Ø 5 mm
OPERATING THE COMPRESSOR
Warning: Make sure that the compressor is switched ff before connecting
it. The ON / OFF switch (position1 in the overview) must not be depressed. In
order to be able to work with the compressor, fi rst take the air hose
(Position 7 in the overview) from its holder on the back of the unit.
CONNECTING THE COMPRESSOR
CAUTION: Do not connect the compressor to both the 230 V household
connection and the 12 V socket of your vehicle at the same time.
CONNECTION TO THE 12 V VEHICLE SOCKET:
Insert the appliance plug of the 12 V vehicle connection cable (position 13 in
the overview) into the 12 V input (position 4 in the overview) of the
compressor. Then insert the vehicle plug of the connection cable into the
vehicle socket. On some vehicles, the ignition must be switched on for the on-
board socket to be active.
CONNECTION TO THE 12 V VEHICLE SOCKET:
Insert the appliance plug of the 12 V vehicle connection cable (position 13 in
the overview) into the 12 V input (position 4 in the overview) of the
compressor. Then insert the vehicle plug of the connection cable into the
vehicle socket. On some vehicles, the ignition must be switched on for the on-
board socket to be active.
PRESETTING THE AIR PRESSURE
Select the unit in which the air pressure is to be displayed by pressing the
(R) button (position 9 in the overview). By pressing repeatedly, the following
units can be set: PSI – BAR – kg/cm². By pressing the (+) button (position 8
in the overview) the value can be increased, by pressing the (-) button
(position 10 in the overview) the value can be decreased. overview) the value
can be lowered.
During the setting process, the display fl ashes. If no more settings are
made, the display shows the value 0.00 continuously after approx. 3 seconds.
Info: The last settings are saved. After switching on again, they are set
again. If you now want to work with other values, you must carry out a new
presetting.
Warning: Never allow the compressor to operate for longer than 10 minutes
without a pause, otherwise there is a risk of overheating. Switch the
compressor off after 10 minutes of use and allow it to cool down fully (at
least 20 minutes) before starting it up again. Never leave the compressor to
operate unattended.
After fi lling a tyre, check the tyre pressure again using a separate air pressure tester (e.g. at a fi lling station, vehicle workshop).
USING THE ADAPTER
Open the lock of the valve connection (Figure 2). Insert the appropriate
adapter for the required purpose into the valve connection. Lock the valve
connection (Figure 4). Insert the adapter into the fi lling connection of your
leisure equipment (ball, infl atable toys etc.). Depending on version, it is
possible that the adapter will need to be held fi rmly during the fi lling
process. Remove the adapter from the valve connection by proceeding in reverse
order, as described above.
CONVERSION TABLE PSI / BAR / KG/CM²
The units are converted as follows:
| 1 psi | = | 0.069 bar | = | 0.0703 kg/cm² |
|---|---|---|---|---|
| 1 bar | = | 1.0197 kg/cm² | = | 14.504 psi |
| 1 kg/cm² | = | 14.223 psi | = | 0.981 bar |
| psi | bar | kg/cm² | ||
| --- | --- | --- | ||
| 10 | 0.7 | 0.7 | ||
| 20 | 1.4 | 1.4 | ||
| 30 | 2.1 | 2v1 | ||
| 40 | 2.8 | 2.8 | ||
| 50 | 3.5 | 3.5 | ||
| 60 | 4.1 | 4.2 | ||
| 70 | 4.8 | 4.9 | ||
| 80 | 5.5 | 5.6 | ||
| 90 | 6.2 | 6.3 | ||
| 100 | 6.9 | 7.0 | ||
| 110 | 7.6 | 7.7 | ||
| 120 | 8.3 | 8.4 | ||
| 130 | 9.0 | 9.1 | ||
| 140 | 9.7 | 9.8 | ||
| 150 | 10.4 | 10.5 | ||
| psi | bar | kg/cm² | ||
| --- | --- | --- | ||
| 0.5 | 7 | 0.5 | ||
| 1.0 | 15 | 1.1 | ||
| 1.5 | 22 | 1.6 | ||
| 2.0 | 29 | 2.2 | ||
| 2.5 | 36 | 2.7 | ||
| 3.0 | 44 | 3.3 | ||
| 3.5 | 51 | 3.8 | ||
| 4.0 | 58 | 4.4 | ||
| 4.5 | 65 | 4.9 | ||
| 5.0 | 73 | 5.5 | ||
| 5.5 | 80 | 6.0 | ||
| 6.0 | 87 | 6.6 | ||
| 6.5 | 94 | 7.1 | ||
| 7.0 | 102 | 7.7 | ||
| 7.5 | 109 | 8.2 | ||
| 8.0 | 116 | 8.8 | ||
| 8.5 | 123 | 9v3 | ||
| 9.0 | 131 | 9v9 | ||
| 9.5 | 138 | 10v4 | ||
| 10.0 | 145 | 11.0 | ||
| psi | bar | kg/cm² | ||
| --- | --- | --- | ||
| 0.5 | 7 | 0.5 | ||
| 1.0 | 14 | 1.0 | ||
| 1.5 | 21 | 1,5 | ||
| 2.0 | 28 | 2.0 | ||
| 2.5 | 36 | 2.5 | ||
| 3.0 | 43 | 2.9 | ||
| 3.5 | 50 | 3.4 | ||
| 4.0 | 57 | 3.9 | ||
| 4.5 | 64 | 4.4 | ||
| 5.0 | 71 | 4.9 | ||
| 5.5 | 78 | 5.4 | ||
| 6.0 | 85 | 5.9 | ||
| 6.5 | 92 | 6.4 | ||
| 7.0 | 100 | 6.9 | ||
| 7.5 | 107 | 7.4 | ||
| 8.0 | 114 | 7.8 | ||
| 8.5 | 121 | 8.3 | ||
| 9.0 | 128 | 8.8 | ||
| 9.5 | 135 | 9.3 | ||
| 10.0 | 142 | 9.8 |
LED WORK LIGHT
The LED work light (position 6 in the overview) is switched on and off by
pressing the switch (position 2 in the overview).
REPLACING THE FUSES
Rotate the tip (Position 20 in Figure 6) of the 12 V plug (Position 18 in
Figure 6) anti-clockwise until it comes away from the plug and then remove.
The fuse (Position 19 in Figure 6) is exposed and can be removed from the
plug. Replace the fuse with another of the same strength (here glass fuse,
fast 15 A 250 V, 6 x 30) and screw the tip back into the plug, Figure 6.
TROUBLESHOOTING
| Error | Possible cause | Measure |
|---|
The compressor does not workt
| The connection cable is not connected correctly.| Check the connection of
the cables and connect them correctly.
For vehicle operation:
No voltage at the on-board socket.
| Switch on the ignition of the vehicle. Check the fuse for the boron socket
and replace it if necessary.
The fuses in the plug of the 12 V car cable has tripped.| Replace the
defective fuse, see section 6.7
MAINTENANCE AND CARE
MAINTENANCE
CARE: When used according to the instructions, the Dual Power Compressor
is maintenance-free. Store the compressor in a dry, frost-free location.
Switch the compressor off before cleaning, separate from the power supply.
Clean the housing of the compressor with a soft, dry cloth. Do not use any
aggressive cleaning agents or solvent-based cleaners. Never allow liquids to
penetrate the housing.
NOTES REGARDING ENVIRONMENTAL PROTECTION
- Do not dispose of electrical appliances in household waste! Discarded electrical and electronic equipment must be collected separately and recycled in an environmentally sound manner.
- Contact your municipal or city government on how to dispose of old electronic equipment.
- The materials are recyclable. You are making an important contribution to protecting our environment through recycling, material recycling or other forms of re-utilising old appliances!
- Dispose of the compressor in accordance with the laws and conditions in your country.
CONTACT INFORMATION
- EAL GmbH
- Address: Otto-Hausmann-Ring 10742115 Wuppertal, Germany
- Address: EAL GmbH Otto-Hausmann-Ring 107 42115 Wuppertal, Germany
- Tell: +49 (0)202 42 92 83 0
- Fax: +49 (0) 202 42 92 83 – 160
- E-Mail: info@eal-vertrieb.com
- Web: www.eal-vertrieb.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>