Goldair GEPH211 Archived Panel Heater with Timer User Manual

Goldair GEPH211 Archived Panel Heater with Timer

General Care and Safety Guide

YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they are supervised or have been given instruction concerning the use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
  WARNING: You must not cover this heater. Covering this heater presents fire risk and will activate the safety fuse; permanently disabling the unit.
  WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
  WARNING: To reduce the risk of fire, keep textiles, curtains, or any flammable material a minimum distance of 1 metre from the air outlet.
  WARNING: In order to avoid overheating or fire, do not cover the heater.

• The heater must not be located immediately below a socket outlet.

• Do not use the heater if it has been dropped or damaged.

• Do not use if there are visible signs of damage to the heater.

• Ensure heater is on a flat, stable, heat-resistant surface.

• Do not use this appliance in the immediate surrounds of a bath, a shower, or a swimming pool or other liquids.

• Keep all objects at least 1 metre from the front and 150mm from the sides of the appliance.

• This appliance is intended for household use only and not for commercial or industrial use.

• Indoor use only.

• Use only the voltage specified on the rating label of the appliance.

• Use this appliance only as described in this manual. Any other use is not recommended by the manufacturer and may cause fire, electric shock or injury.

• The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills.

• Never use the appliance to dry clothes.

• Always unplug appliance when not in use.

• Do not connect the appliance to mains supply until completely assembled and adjusted.

• Ensure hands are dry before handling the plug or main unit.

• Do not operate with cord set coiled up as a heat build up is likely, which could be sufficient to become a hazard.

• Carry out regular checks of the supply cord to ensure no damage is evident

• Do not operate this appliance with a damaged cord, plug or after the appliance malfunctions or has been dropped or damaged in any manner. Return to a qualified electrical person for examination, electrical service or repair.

• Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to weaken and split. Always ensure that all cord has been removed from any cord storage area and is unrolled before use.

• It is recommended that this heater is plugged directly into the wall socket. Power boards are not rated to supply power to high wattage appliances.

• A correctly specified, undamaged extension cord may be used with this heater provided it is used in a safe manner.

• Do not remove plug from power socket until the appliance has been switched off.

• Do not remove plug from power socket by pulling cord; always grip plug.

• Do not place cord under carpet or cover with rugs or furniture. Arrange the cord so it cannot be tripped over.

• Don’t place appliance on bedding or on thick & long carpet where the openings may get blocked.

• Switch off and use handle provided when moving

• Do not place appliance close to radiant heat source.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the appliance.

• Do not sit on the appliance.

• Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) rinsed in hot soapy water only. Always remove plug from the mains supply before cleaning.

• Do not operate in areas where petrol, paint or other flammable liquids are used or stored.

• The appliance must not be immersed in any liquids.

• There are no user serviceable parts installed in the unit.

• Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards.

• This unit is not supposed to be used in or around locations where foodstuffs, works of art or delicate articles of science, etc are stored.

• When the appliance has been unpacked, check it for transport damage and ensure all parts have been delivered. If parts are missing or the appliance has been damaged, contact the Customer Services Team.

• If your appliance does not work, or is not working properly, contact the place of purchase or the Customer Services Team.

Components

Screw pack components

• Drill bits x 2
• (1 x 7mm for plasterboard or wooden walls,
• 1 x 8mm for masonry walls) Mounting Plugs x 4
• Screws x 4
• Screw Caps x 4

Wall Mounting & Position Instructions

Always choose a safe location for the heater, keeping in mind the safety precautions outlined below. The heater needs to be mounted so that the power switch is in the top right hand corner. Do not run the power cord behind the heater. This will determine where you mount the heater in relation to where the power socket is located.
NOTE: Your Goldair EcoPanel Heater should be installed with at least 300mm clearance from the floor and any other surrounding parts including other appliances, side walls, ceilings, shelves and soft furnishings.
DO NOT RUN THE POWER CORD BEHIND THE HEATER WALL MOUNTED HEATERS ARE ONLY TO BE MOUNTED ON WALLS THAT COMPLY WITH CURRENT AS/NZS SPECIFICATIONS & BUILDING REGULATIONS MAKE SURE THE APPLIANCE IS UNPLUGGED AND POWER SWITCHES ARE OFF

Orientation.
The heater must be mounted on the wall with the power switch in the top right hand position as shown below.
Note: Do not run power cord behind the heater.

NOTE : Your Goldair EcoPanel Heater should be installed with at least 300mm clearance from the floor and any other surrounding parts including other appliances, side walls, ceilings, shelves and soft furnishings.

1. Mark the positions of the four holes to be drilled on the wall. Ensure there is a 300mm clearance on all sides of the heater.
2. Drill holes with an appropriate drill bit for the wall surface you are mounting the heater on to.
3. Insert the plastic rail fittings into the holes.
4. Install the panel heater onto the four rail fittings matching the four holes on the heater.
5. Screw the four screw bolts into the plastic rail fittings.
6. Put the caps onto the end of the screw bolts. It is recommended to use some normal glue to stick the caps onto the bolts steadily.

To remove the unit from the wall, simply remove the bolt caps, unscrew the bolts with a screw driver and take the heater down.

Operating Your Heater

Always choose a safe location for the heater, keeping in mind the safety precautions outlined. Ensure all packaging has been removed from the unit before use. Please follow the below instructions.
WARNING : In order to avoid overheating or fire, do not cover the heater.
WARNING : Keep all objects at least 1 metre from the front and 300mm from the sides of the appliance.
WARNING: Do not use this heater with a programmer, separate timer, remote-control system or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
WARNING: This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
WARNING: Never leave this heater unattended while in use.

WALL MOUNTED HEATERS ARE ONLY TO BE MOUNTED ON WALLS THAT COMPLY WITH CURRENT AS/NZS SPECIFICATIONS & BUILDING REGULATIONS

Once the heater is in a safe operating position and all switches are in the off position, insert the power plug into the mains outlet.
CAUTION: Ensure the power cord is not tight because if pulled it may partially pull the plug from the socket. A partially inserted plug will overheat the plug and socket and could result in fire.
WARNING: This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.

Your Goldair Panel Heater will provide background warmth. This Panel Heater is designed to take the chill off the room.

The surface of this Panel Heater can be painted with good quality paint (acrylic or enamel).
Decorating tip: All wall mounted heaters may cause paint to discolour or wall paper to lift.

OPERATING INSTRUCTIONS

• Before plugging in and using your new Goldair panel heater, check all surfaces to ensure the heater is not damaged in any way.
• Check that the On/Off switch is set to the Off position before plugging the heater into the mains supply.
• Use the On/Off switch along the side of the heater to turn your heater on.

TIMER

• You must set the time prior to programming the Timer. To do this; turn the outer dial of the timer in a clockwise direction until the time of the day (24-hour clock) corresponds with the triangular marking. Example if it is 2pm (1400 hours) then set the triangular mark in line with 14. One complete turn of the dial corresponds to 24 hours.
• There are 96 “riders”, positioned around the dial, each rider represents 15 minutes.
• Where all the “riders” are pushed to the outside of the timer the appliance will be ON continuously.
• To set a specific time for example:
• If you want the appliance to be on from 6pm to 10pm, then set all the riders from 18 to 22 (1800 hours to 2200 hours) to the outside of the rim and all other riders to the inside of the timer. The unit will then turn on automatically at 6pm and off again at 10pm.

SAFETY DEVICES
This appliance has two protection devices:

• Resettable thermal link – this will automatically disconnect the power to the appliance at a pre-set overheat temperature. After cooling down it will reset and power on again. If this occurs, investigate what is causing the appliance to overheat.
• Thermal fuse – this disconnects the appliance permanently in case of overheating. (It is non resettable).

Note: The light in the power switch will remain on even after the safety devices have activated to show there is still power to the heater
CAUTION: The heater generates heat during use. Proper precautions must be taken to prevent the risk of burns, scalds, fires or other damage to persons.

CARE AND CLEANING

• The heater requires regular cleaning to ensure trouble free operation:
• Unplug the heater from the mains supply before cleaning.
• Ensure that the heater has been allowed to cool down completely before cleaning.
• The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills.
• Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and dirt.
• Never use solutions such as petrol, thinners or polishing agents.
• Ensure the heater is dry before plugging back into the mains supply.

Three Year Warranty

Thank you for purchasing this Goldair product. Your product is warranted against faults and manufacture when used in normal domestic use for a period of three years. In non-domestic use Goldair limits the voluntary warranty to three months.
Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the warranty period.
This warranty excludes damage caused by misuse, neglect, shipping accident, incorrect installation, or work carried out by anyone other than a qualified electrical service technician.
PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY.
The benefits given to you by this warranty are in addition to other rights and remedies available to you under law in relation to the goods or services to which this warranty relates.
In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act (1993).

Goldair – New Zealand
CDB Goldair
PO Box 100-707
N.S.M.C
Auckland
Phone +64 (0)9 917 4000 Phone 0800 232 633 www.goldair.co.nz

Goldair – Australia
CDB Goldair Australia Pty PO Box 574
South Morang
Victoria, 3752

Phone +61 (0)3 9365 5100
Phone 1300 GOLDAIR (1300 465 324) www.goldair.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>