SOAR972 2MP Mobile PTZ Camera LTE 4G With SIM Card User Manual

SOAR972 2MP Mobile PTZ Camera LTE 4G With SIM Card

Product Information

The product is a camera with a built-in router and WiFi
functionality. It has various buttons and display screens for easy
operation. The camera can be mounted on a tripod and comes with a
shock bracket for stability. It also has special preset functions
and factory default parameters.

Product Usage Instructions

1. Safety Instructions

Before using the product, please read and follow the safety
instructions provided in the user manual to ensure safe
operation.

2. Product Parameters

Refer to page 4 of the user manual for detailed information
about the product parameters.

3. Factory Default Parameters

Page 8 of the user manual provides information on the default
parameters of the camera, router, and WiFi settings.

4. Description of Buttons and Display Screens

Page 9 of the user manual explains the different buttons and
their functions, as well as the display screens and their
descriptions.

5. Special Preset Function

Page 11 of the user manual provides instructions on how to use
the special preset function of the camera.

6. Installation Instructions

Refer to page 12 of the user manual for detailed installation
instructions, including power cord interface definition, aviation
plug connection, rear panel interface definitions, tripod mounting
method, dome size, and shock bracket dimensions.

7. WiFi Instructions

Page 18 of the user manual provides instructions on how to
connect and use the WiFi functionality of the product.

8. Common Problems and Solutions

Page 21 of the user manual lists common problems that may occur
during usage and provides solutions to resolve them.

9. Appendix: Instructions for Using the Built-in Router

Refer to page 22 of the user manual for instructions on setting
up and managing the built-in router, including preparing for setup,
operating modes, wireless security settings, and device
management.

Machine Translated by Google
[Quickly deploy the ball] User Manual V2.0 ÿ Please read this manual carefully before using itÿ

Machine Translated by Google

Table of contents

1. Safety Instructions………………………………………………………………………………………………1

2. Product parameters……………………………………………………………………………………. 4

3. Factory default parameters……………………………………………………………………………………… 8

Camera……………………………………………………………………………………………………. 8

router……………………………………………………………………………………. 8

WIFI………………………………………………………………………………………..8

4. Description of buttons and display screens……………………………………………………………………………….. 9

Buttons:……………………………………………………………………………………………………… 9

Display Description:…………………………………………………………………………………………… 9

5. Special preset function……………………………………………………………………………………. 11

6. Installation Instructions……………………………………………………………………………………. 12

Power Cord Interface Definition……………………………………………………………………. 12

Aviation plug connection………………………………………………………………………………………….. 12

Rear Panel Interface Definitions…………………………………………………………………………. 13

Tripod Mounting Method (Tripod is optional)…………………………………15

Dome size………………………………………………………………………………………………………….17

Shock Bracket Dimensions………………………………………………………………………………. 17

7. WiFi Instructions…………………………………………………………………………………………………….18

8. Common problems and solutions…………………………………………………………………………..twenty one

IX. Appendix: Instructions for using thebuilt-in router…………………………………………………………….. twenty two

Preparing for Setup………………………………………………………………………………. twenty two

Operating mode……………………………………………………………………………………25

wireless security settings…………………………………………………………………..32

Device Management……………………………………………………………………………………. 40

Machine Translated by Google
1. Safety Instructions

Instructions for Quickly Deploying the Ball

Personnel responsible for the installation and routine maintenance of this equipment must possess basic skills in safe operation. in operation Before using the device, be sure to carefully read and implement the safety regulations specified in the product manual. ÿ This is a Class A product, which may cause radio interference in a living environment. In this kind of
In such cases, the user may be required to take practical measures for its interference. ÿ Make the equipment work within the allowable temperature and humidity range, and avoid being exposed to extrusion, vibration, humidity, etc.
Dusty, extremely hot, extremely cold, strong electromagnetic radiation and other places. ÿ Under normal circumstances, the device is installed outdoors, and the device connection should be effectively waterproof and moisture-proof.
Air, sand and dust prevention measures (especially the screws at the connection of the equipment must be tightened to ensure the overall tightness). To prevent lightning strikes, please install lightning arresters. ÿ Do not aim the lens at a strong light object for a long time, especially do not aim it at the sun or other strong objects. light source, otherwise it may cause permanent damage to the imaging device of the device. ÿ Please use the power adapter provided by our company. It is possible to use a power adapter that does not meet the requirements. can cause damage to the device. ÿ If the power cable between the power adapter and the device is too long, the voltage reaching the device will be low. It is easy to cause the equipment to work abnormally. If you need to extend the power cord, please refer to “Power Cord Requirements”. ÿ Disconnect the power supply before moving the device. Be careful when moving it. Once the power cord is plugged into the power supply, The device will power up. When moving the equipment, do not carry the weight by the tail wire, so as to avoid the equipment cable The interface is loose. ÿ Do not cut the pigtails for connection. The exposed pigtails may cause a short circuit and cause abnormal damage to the device.
1

Machine Translated by Google
Instructions for Quickly Deploying the Ball
ÿ For external connection ports, please use existing cable terminals to connect. When connecting, confirm the cable terminal (lock buckle/snap) good and fastened in place;
ÿ Do not pull the cable excessively during the installation process, and keep a certain margin to prevent vibration and shaking. Causes poor or loose port contact.
ÿ The tail wire should not be exposed, and the area where the tail wire is located must be completely waterproof (waterproof junction box or seal). cavity); the tail wire needs to be waterproofed (see “Waterproof treatment of tail wire”) to avoid tail wire Soak in standing water.
ÿ In the process of turnover and transportation, the front face needs special protection to avoid friction, scratches, pollution, etc. In order to keep the front face clean, please do not remove the transparent protective film of the front face during the installation process. After the installation is complete, remove the transparent protective film before starting the device.
ÿ For product maintenance issues, please consult professionals, and do not open the cover for maintenance without authorization. ÿ It is strictly forbidden to use or place the product in high temperature (in the hot sun or in a very hot car), it may cause damage to the product.
Cause the battery to overheat, catch fire or malfunction, and shorten its life. ÿ It is strictly forbidden to disassemble, change, directly weld the battery and pierce the battery with nails or other sharp objects. ÿ It is strictly forbidden to use it in places with strong static electricity and strong magnetic fields, otherwise it will easily damage the battery safety protection device and bring about
unsafe hazard. ÿ It is strictly forbidden to cut the casing and remove the outer casing of the battery. ÿ The battery cannot be used under extreme conditions, such as: extreme temperature, deep cycle, extreme overcharge and
Overdischarge. ÿ Please store the battery in a cool and dry place. If a large number of batteries are stored or shipped, the battery must be put
Out of power. ÿ If the internal battery emits odor, heat, discoloration, deformation, noise, leakage or use, storage,
If any abnormality occurs during the charging process, it should be stopped immediately and safety measures should be taken. ÿ Under normal circumstances, the allowable range of battery charging ambient temperature is 0 to 45°C, and the discharge ambient temperature is allowable.
The allowable range is -20 to 60 °C.
storage
ÿ The storage environment should be in a clean, dry and ventilated room. Contact with corrosive substances should be avoided. Keep away from fire and heat sources. Under normal circumstances, the allowable range of storage ambient temperature does not exceed 3 months
2

Machine Translated by Google
Instructions for Quickly Deploying the Ball
It is -20ÿ40ÿ, and the allowable range of storage ambient temperature for not more than 6 months is the allowable range of ambient temperature. The temperature is -20ÿ35ÿ, and the allowable range stated in the product specification shall prevail for special products. Ben Gong The best storage environment temperature recommended by the company is 20 to 25 ÿ. ÿ Under normal circumstances, the allowable range of relative humidity in the storage environment is 65±20%. Best recommended by our company The relative humidity of the storage environment is 50-70%. ÿ The product should not be stored at high temperature or high humidity, otherwise it will cause battery leakage, rust, etc. and reduced capacity. ÿ Long-term storage may cause the capacity of the battery pack to decrease, and it will take 1-3 charge/discharge cycles The highest discharge capacity can be achieved. After the battery has been placed for three months, it needs to be recharged or cycled to charge and discharge once. If the storage period exceeds 6 months, charge-discharge activation should be performed to reduce performance loss. Disclaimer of liability The company is not responsible for any accident caused by the pool. ÿ The company has the right to revise the product specifications and other documents provided by the company. The company will notify the customer after the revision. Sincerely hope that users can strictly follow the product specifications and other documents provided by the company and the attached documents. Pay attention to the terms of use, storage, and transportation of batteries. Improper use, storage and transportation of batteries, such as Accident or fire may cause the battery to heat up, catch fire or rupture.
3

Machine Translated by Google

Instructions for Quickly Deploying the Ball
2. Product parameters
WiFi wireless Protocol standard IEEE 802.11b/IEEE 802.11g/IEEE 802.11n

Wireless rate 300Mbps

Channel selection 1~11 frequency band

Band bandwidth 20/40MHz optional

wireless security

64/128-bit WEP encryption; WPA-PSK/WPA2-PSK, WPA-PSK, WPA2-PSK security mechanism.

4G wireless transmission (optional)

frequency band

LTE-TDD/LTE-FDD/WCDMA/TD-SCDMA/EVDO/CDMA/GSM seven-mode full Netcom frequency band

SIM card type Micro SIM card

Positioning (optional) Positioning system GPS/Beidou

lithium battery
Battery type Large capacity polymer lithium battery Battery capacity 11.1V 8000mAH 10 hours of battery life (infrared light off, in low power mode)

camera Image sensor 1/2.8 inch CMOS

4

Machine Translated by Google

sensor total pixels

Approx. 2.42 million pixels

Instructions for Quickly Deploying the Ball

Horizontal resolutionÿ1000TVL

maximum image size

1920×1080

Color: 0.001Lux@(F1.5,AGC) B&W:

Minimum illumination

0.0005Lux@(F1.5,AGC)

Gain control auto/manual

3D noise reduction support

2D noise reduction support

signal to noise ratio

ÿ55dB

white balance

automatic / manual

Electronic shutter 1/25ÿ1/100,000 seconds; supports slow shutter

Electronic image stabilization support

Fog function support

Backlight Compensation Support

wide dynamic

support

Strong light suppression support

Digital zoom 16 times

Day and night mode automatic ICR filter color to black

Focus Mode Auto/Semi-Auto/Manual

focal length

5.5ÿ180mm

The zoom speed is about 3.5 seconds (optical, wide-angle-telephoto)

5

Machine Translated by Google

Instructions for Quickly Deploying the Ball

field of view

60.5ÿ2.3 degrees (Wide-Telephoto)

close-up

100ÿ1000mm (Wide-Telephoto)

Optical zoom 33 times

Aperture value

F1.5ÿF4.0

Function

Main stream resolution and frame rate

50Hz: 25fps (1920 × 1080, 1280 × 960, 1280 × 720); 60Hz: 30fps (1920 × 1080, 1280 × 960, 1280 × 720)

Resolution and frame rate of the third stream

Independent of the main stream setting, maximum support: 50Hz: 25fps (1920 × 1080); 60Hz: 30fps (1920 ×1080)

video compression

H.265 ÿMain Profile ÿ/ H.264 ÿBaseLine Profile / Main Profile / High Profile / MJPEG

Audio compression G.711a/G.711u/G.722.1/G.726/MP2L2/AAC/PCM

Network protocol
ROI

IPv4/IPv6,HTTP,HTTPS,802.1x,Qos,FTP,SMTP,UPnP, SNMP,DNS,DDNS,NTP,RTSP,RTP,TCP,UDP,IGMP,ICMP,D HCP,PPPoE support

SVC

support

Area Exposure/ Focus

support

Time display support, such as: week, date

6

Machine Translated by Google

Instructions for Quickly Deploying the Ball

application programming ONVIF(PROFILE S,PROFILE G) ,GB28181-2016, a private agreement

mouth

browser Simultaneous preview users

Support IE7 and above (including IE7) Google, Firefox, Apple and other nonIE browsers Up to 6 way

safe mode

Authorized username and password, and MAC address binding; HTTPS encryption; IEEE 802.1x network access control (whitelisting)

User management Multi-level user rights management

storage
storage card
PTZ

Support Micro SD/SDHC/SDXC card (128G) off-network local storage, NAS (NFS, SMB/CIFS are supported)

Horizontal range 360°

Horizontal speed 0.05ÿ80°/s

Vertical range -25ÿ90°

Vertical speed 0.05ÿ60°/s

Preset

255

cruise

6 bars, each bar up to 18 points

Pattern scan 4 strips

Power-down recovery support

Infrared function

Infrared distance 50 meters

7

Machine Translated by Google

Instructions for Quickly Deploying the Ball

conventional

powered by

DC 9ÿ24V, wide voltage input

Power consumption

MAX 48W

Working temperature -20ÿ60°C

weight

3Kg

Protection class IP66

3. Factory default parameters

1. Camera
Camera IP address: 192.168.1.68 Camera username: admin Camera password: system123
2. Router
Router IP address: 192.168.1.1 Camera username:admin Camera password:admin
3. WIFI
The WiFi wireless name (SSID) is: Wifi-7628-XXXX Password: 12345678

8

Machine Translated by Google

4. Description of buttons and display

Instructions for Quickly Deploying the Ball

1. Buttons:

ÿ Power on: When the device is powered on, it is in the off state. In the off state, press and hold the button (more than 3 seconds and less than 10 seconds), when the green indicator light of the button is on, the button can be released and the device is turned on.

ÿ Power off: When the device is on, long press the button (more than 3 seconds and less than 10 seconds), press
When the green indicator light of the button is off, you can release the button and the device will shut down.

ÿ Router reset: When the device is powered on, long press the button (more than 10 seconds), the green button When the color indicator turns off and then lights up, release the button to reset the built-in router. The device is still powered on.

2. Display description:

GPS Display

Network Type Signal Strength

LTE Acquisition Time

Battery Level

PTZ Indicate

ÿ Network type: There are five network type statuses: 2G, 3G, 4G and not acquired
Among them, 2G, 3G, and 4G are displayed in characters, and the unobtained icons are Note: Even if no SIM card is inserted, the wireless router should indicate 2G or 3G after 30s of power on. ÿ Signal strength:
There are six signal strength status indications: 9

Machine Translated by Google
Instructions for Quickly Deploying the Ball
Note: No valid SIM card is inserted and the router has not been started and completed, and the display has not been obtained.
ÿ GPS indication:
The GPS indication has three states: no display (no GPS function or GPS abnormality), display but flashing (no GPS function or GPS abnormality) Positioning is successful), displayed without flashing (positioning is successful)
ÿ 4G acquisition time: There are two states for 4G acquisition time: NOTGET (not acquired), time indication (successfully acquired 4G time)
Note: The time can only be obtained after inserting a valid SIM card and successfully connecting to the Internet
ÿ Battery level indicator: The battery level indicator has two states: battery power and charging state.
Indication on battery power:
When the battery power is too low icon toggle) as an alarm.
Indication while the battery is charging: When the device is connected to a power supply with a voltage of DC9~24V and a power of not less than 48W, and the ambient temperature is lower than
At 60°C, the device will enter the charging state. In the power-on state, the battery indicator on the display will be displayed at a frequency of 1Hz. Switch back and forth between the icon of <20% and the next state icon of the current state, if the current power is less than 60%, the power The battery level indicator area will switch in sequence among the following 4 icons
10

Machine Translated by Google

Instructions for Quickly Deploying the Ball

ÿ PTZ indication As shown in the figure: P: represents the horizontal angle, the range is 0ÿ360°; T: represents the vertical angle, the range is
-25°ÿ90°; Z: represents the zoom value, the range is 1ÿ33.

5. Special preset function

action
set up transfer transfer transfer transfer

Preset No 76 76 78 79 80

3
Auxiliary switch
4
Auxiliary switch

Function
High-precision self-test mode Low-precision self-test mode (factory default) Low power consumption mode, the motor stops and the locking torque is small Medium power consumption mode, the motor stops and locks the torque High power consumption mode, the motor stops rotating and the locking torque is large
Turn on the defogging fan on or Turn off the defogging fan (heating is off if heating is on)
Turn on the heating (if the fan is not turned on, it is turned on) or Turn off the heating (the fan remains in the state it was before the heating was turned on)

11

Machine Translated by Google
Instructions for Quickly Deploying the Ball
6. Installation Instructions 1. Definition of power line interface
ÿPower cord: The car ball needs to provide DC12V, 5A power input. ÿ RS485 control line: 485 control line. ÿNetwork interface: network signal output, RJ45 crystal head. ÿ Q9 interface: analog video signal output. 2. Aviation plug connection
Schematic diagram of aviation plug
12

Machine Translated by Google

Instructions for Quickly Deploying the Ball

Schematic diagram of aviation plug connection As shown in the picture, the large depression of the cable is aligned with the large protrusion of the aviation socket, then insert it, and then tighten the turnbuckle.
3. Rear panel interfacedefinition

The rear panel interface includes SIM card interface, TF card interface, and router reset button.
13

Machine Translated by Google
Instructions for Quickly Deploying the Ball
Notice:
ÿ The inserting positions of the SIM card and the TF card are as shown in the figure: the SIM card and the TF card must be powered off.
It is strictly forbidden to insert or unplug it in the working state. SIM card chip facing down, notch facing out
Insert it into the card slot; the gold finger side of the TF card is facing up, and the notch is facing inward to insert the card slot. ÿ When the router configuration problem prevents you from entering IE to access the router, you can
Press and hold the router reset button for 10 seconds in the machine state to restore the router to default.
ÿWhen the interface cover is opened and then installed, care must be taken that the sealing ring is installed in place, and the fixing screws need to be tightened.
tight to prevent water leakage.
14

Machine Translated by Google

Instructions for Quickly Deploying the Ball

4. Tripod installation method (tripod is optional)
ÿFor detailed instructions on using the tripod, please refer to the manual of the tripod;

ÿRemove the tripod quick release plate TY-50E;

ÿRemove the original camera screws of the quick release plate;
15

Machine Translated by Google
Instructions for Quickly Deploying the Ball
ÿUse 2 M4*8 stainless steel screws and M4 flat washer to fix the quick release plate to the support on the back of the quick release plate.
on the tray;
ÿReinstall the quick release plate on the tripod, and then attach the control ball to the support plate.
16

Machine Translated by Google
5. Dome size

Instructions for Quickly Deploying the Ball

6. Shock mount size

17

Machine Translated by Google

Instructions for Quickly Deploying the Ball
7. WiFi Instructions

The product has a built-in WiFi hotspot, which can be directly connected to the dome through a mobile phone (tablet or computer).

WiFi hotspot to preview images and gimbal control.

The mobile phone or tablet needs to download the APP client to use, enter the application store to search

“iVMS-4500”, download and install. The computer can be operated directly through the WEB.

After the dome camera is powered on and turned on, the mobile phone (tablet or computer) needs to be turned on to search for WiFi. By default

Wireless signal name (SSID) “Wifi-7628-XXXX”, password “12345678”, connect to the WiFi

hot spot.

The following introduces the quick use method of iVMS-4500 for Android mobile phone:

1. After entering the app, it is located in the “Live Preview” item,

2. Then enter the “Device Management” menu

Enter the “Settings” menu

18

Machine Translated by Google
3. Enter “+” to add device, select “Online”
equipment”

Instructions for Quickly Deploying the Ball 4. Automatically retrieve online devices in the LAN, click Select the device to be added

5. Select “Add”

6. Enter username, password and “Save”

19

Machine Translated by Google
Instructions for Quickly Deploying the Ball
7. Return to the real-time preview and select the real-time preview channel 8. PTZ control
20

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>