Turnils North America AMP28BDCV2 DC Tubular Motor with Built in RF Control User Manual

**Turnils North America AMP28BDCV2 DC Tubular Motor with Built in RF Control User Manual

**

Declarations

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement

The device is compliance with RF field strength limits, users can obtain Canadian information on RF exposure
and compliance.

This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-003 (B)/NMB-003(B)

Quick Index

(hold down for 2s)
Lower Limit: Down (hold down for 2s) > Down + Stop (hold down for 2s)
4 Add / Remove Favorite Position| P2 > Stop > Stop
5 Roller Mode & Sheer Mode Switch| Up + Down (hold down for 5s) > Stop
6 Adjust Limits| Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold down for 2s)
Lower Limit: Down + Stop (hold down for 5s) > Up or Down > Down + Stop (hold down for 2s)
7 Pair / Unpair Additional Emitter| P2 (existing) > P2 (existing) > P2 (new)
8 Speed Regulation| Acceleration: P2 > Up > Up
Deceleration: P2 > Down > Down

Troubleshooting

compatible AC adaptor and check connection and positioning of solar PV pane
Insufficient charging from Solar PV Panel| Check connection and orientation of solar PV pane
Remote control battery is discharged| Replace battery
Battery is inserted incorrectly into remote contro| Check battery polarity
Radio interference / shielding| Ensure remote control and the antenna on the motor are positioned away from metal objects
Receiver is far away from Remote Control| Move remote control to a closer position
Power failure| Check power supply to motor is connected and active
ncorrect wiring| Check that wiring is connected correctly (refer to motor installation instructions)
Motor beeps 10 times when in use| Battery voltage is low / PV (solar panel issue)| Recharge with AC adapter or check connection and positioning of solar PV panel
Cannot program a single motor (multiple motors re| Multiple motors are paired to the same channel.| Always reserve an individual channel for programming functions
SYSTEM BEST PRACTICE – Provide an extra 15 channel remote in your multi-motor projects that provides individual control for each motor for programming purposes
Place all other motors into sleep mode (ref to P1 button instructio

Fields of Application

• Roller

• Sheer

• Banded

• Roman

Specifications

Working temperature: -10º C : ~ +50º C Radio Frequency: 433.925 MHz
Input Voltage: USB 5V 1A : / USB 5V 2A Maximum Running Time: 6 minutes

The motor is suitable for motorization of roller shades, sheer shades, roman shades, and revolve shades.

Attention

Never drop, knock, drill or submerge the motor. Keep the power cable in the proper position as shown below.

Read all safety instructions before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Safety Instructions

1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls should be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty.

Charging Instructions

This motor connects with an external Li-ion battery pack with integrated charge management.

Max power input for recharging: 5V 2A.

Before first use please charge motor for 6 hours using a 5V charger.

During operation, if the voltage is detected to be too low, the battery stops running and needs to be recharged

Rechargeable Battery

Solid Red: Charging in process

Solid Green: Battery has finished charging

P1 Button Instructions

1. Test Motor
   Happening as you press for 1 second
   Press P1 Less than 1 sec.
   when released
   Motor Response: Wakes & Runs

2. Activate Pairing Mode
   Happening as you press for 2 seconds
   Press P1 Approx. 2 sec.
   Until Shade: Jog x1

3. Sleep Mode
   Happening as you press for 6 seconds
   Press P1 Approx. 6 sec.
   Until Shade: Jog x2

4. Reverse Direction
   Happening as you press for 10 seconds
   Press P1 Approx. 1
   Until   Shade : Jog x3

5. Reset To Factory Settings
   Happening as you press for 14 seconds
   Press P1 Approx. 14 sec
   Until Shade: Jog x4

Button Instructions

Essential Settings

The steps in factory mode must be completed to ensure proper operation.

Pair / Unpair Remote Control

• a. Press “P1” button (about 2 sec) on the motor head until motor jog x1 and beep x1.
  Action on Motor Motor Response

• b. In the next 10 secs, press and hold “Stop” button on the remote control until motor jog x2 and beep x3.
  Action on Remote Control Motor Response

Change Motor Direction (if necessary)

Press “Up” or “Down” button to check if the shade moves in the desired direction.

If you need to reverse the direction, press and hold (about 2 sec) “Up” and “Down” buttons simultaneously until motor jog x1 and beep x1. Action on Remote Control  Motor Response

• The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing P1 button (See P1 button instructions).

Setting the Upper and Lower Limits

Set Upper Limit

• a. Press “Up” button to raise the shade, then press “Stop” button when it is in the desired upper limit.
  Action on Remote Control

• b. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.
  Motor Response

Set Lower Limit

• a. Press “Down” button to lower the shade, then press “Stop” button when it is in the desired lower limit.
  Action on Remote Control

• b. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.
  Motor Response

Adjust Limits

Adjust the Upper Limit

• a. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
  Action on Remote Control Motor Response

• b. Use “Up” button to raise the shade to the desired highest position, and use “Up” or “Down” button to do the final adjustment if necessary.
  Action on Remote Control

• c. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3
  Motor Response

Adjust the Lower Limit

• a. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
  Action on Remote Control Motor Response

• b. Use “Down” button to lower the shade to the desired lowest position, and use “Up” or “Down” button to do  the final adjustment if necessary.
  Action on Remote Control Motor Response

• c. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

Favorite Position

Set Favorite Position

• a. Use “Up” or “Down” button to move the shade to desired Favorite position.
  Action on Remote Control Motor Response

• b. Press and hold (about 2 sec) one “P2” button onthe back of remote control until motor jog x1 and beep x1.
  Action on Remote Control Motor Response

• c. Press and hold (about 2 sec) “Stop”button until motor jog x1 and beep x1.

• d. Once more, press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.

Send Shade to Favorite Position

Press and hold (about 2 sec) “Stop” button, motor will move to Favorite position.
Action on Remote Control Shade Response

Delete Favorite Position

• a. Press and hold (about 2 sec) one “P2” button until motor jog and beep x1.
  Action on Remote Control Motor Response

• b. Press and hold (about 2 sec) “Stop” button until motor jog and beep x1.
  Action on Remote Contro

• c. Once more, press and hold (about 2 sec) “Stop” button until motor jog x1 and long beep x1.

Roller Mode and Sheer Mode

Roller Shade Mode – continue movement after a short press – Default Mode

• a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.
  Action on Remote Control Motor Response

• b. Press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.
  Action on Remote Control Motor Respons

Adjust Motor Speed

Acceleration Speed

• a. Press one “P2” button until motor jog x1 and beep x1.
  Action on Remote Control Motor Response

• b. Press “Up” button until motor jog x1 and beep x1.
  Action on Remote Controlv Motor Response

• c. Once more, press “Up” button until motor jog x2 and beep x1.

  ---

Deceleration Speed

• a. Press one “P2” button until motor jog x1 and beep x1.
  Action on Remote Control Motor Response

• b. Press “Down” button until motor jog x1 and beep x1.
  Action on Remote Control Motor Response

• c. Once more, press “Down” button until motor jog x2 and beep x1.

Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately

Please scan QR code to see more AMP™ product information

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>