PuriSystems PuriCare 500 and 500IG User Manual

PuriSystems PuriCare 500 and 500IG

INTRODUCTIION

PuriCare550/550IG is small in size and lightweight. The machine is equipped with two lightweight filtering devices to avoid the unnecessary increase in weight and volume increase. It effectively enhanced the air purification capability that allows to the filtration of small particles such as dust, sawdust, and many more.

IDENTIFICATION

Congratulations on purchasing a PuriSystem dust collector. For your convenience in submitting a warranty claim in the future, be sure to note the serial and the date of purchase below.

HOW IT WORKS

• Connect the dust collector to a standard 115V/60Hz outlet.
• Refrain from moving the unit during operation.
• Keep both air inlet and outlet away from the wall or any obstructions for at least 2 ft..
• This product can only filter dust particles above lum.

WARNING

Please note that the dust collector can only be used with Purisystems approved accessories. Using unauthorized accessories or making changes to the machine may invalidate your warranty. Please contact us for more details.

• The power cord of the machine must be plugged into a grounded socket.
• The power supply ofthe machine must not be higher than the specified power supply.
• The machine should not be installed outdoors or in places that may be eroded by Rain Water to avoid damaging the electrical components and Fire.
• Do not run the machine without a filter installed.
• If hooks are installed on the ceiling, the load bearing capacity of the ceiling must be greater than 110 lbs.
• If the dust collector is to be installed on the ceiling, the distance between the bottom of the dust collector and the ground must be greater than 7
• Installation requires two people.

SPECIFICATION

KEY FEATURES

INSTRUCTIONS

CONTROL PANEL

REMOTE CONTROL

Power key

Turn on and off air filtration equipment  Click the control panel “ON/OFF” /remote control”ON/OFF”.The machine will make a “drip” sound, the environment prompt light will be on, and the display screen will display the PM number of the environment.

Wind speed key:

Control the wind speed of Low, Middle and High. Each time it is operated, the light of the control panel will switch to one of the wind speed gears, and the light represents the wind speed of the current gear.

Timing

Control the working hours of the machine: Operate the remote control “TIME” button, The display screen will display a timing number. ,the “TIME” button once, and display the content once (OH, lH, 2H, 3H, 4H, SH, 6H). OH stands for indefinite time, (lH, 2H, 3H, 4H, SH, 6H) the number,is the running time of the machine, and H represents the hour. After setting the working hours, the display content automatically switches to the environment PM to detect the content value, which means that the command takes effect and starts the countdown work.

Ionizer svvilch button:

version does not have this feature, so you need to pay attention to the version model when you buy it. Operate the “IONIZER” button of the remote control, the ionizer switch light on the control panel is on,the ion function starts, and operate again, the ionizer switch light is off and the ion is off.

Rise Drop

Description: this button function is only used on the remote control. Operate the up arrow and down ar row of the remote control.Set the desired PM number.The setting number can be switched within CO- 800, and the display number rises or decreases by SO peroperation. The minimum CO number is set to rep rrepresent the continuous operation of the machine and is not affected by the PM sensor. When the PM number in the display screen is higher than the set number, the machine is running.

Environmental warning lamp

Color

|

Green

|

Yellow

|

Red

Air Quality|

Excellent

|

Good

|

Bad

Note: please pay attention to the air quality of the room when it is shown in red.

HOW TO INSTALL DUST COLl.ECTOR

Installation mode 1

• Fix the hook as shown in the picture to 4 holes at the top of the machine with M4 nut. M4 nut needs
  to be tightened to prevent the hook from rotating and falling off.

• Fasten the horn hook to the ceiling.

• Two people are required for this installation. One(1) person to pick the dust collector and the other to connect the end of the chain to the machine hook.

• Due to the impact of the machine itself and the environment, there will be installation imbalance, the
  number of sections of the chain hook can be used to adjust the machine balance.

Installation mode 2

• Remove the four M4 screws from the top of the machine, install the pendant as shown in the picture, and fix the M4 screws just now.
• 0ne man picked up the dust collector and the other screwed the machine to the wall.

HOW TO REPLACE THE ALTER

1. Turn off the machine before replacement.
2. Loosen the buckles on the side of the machine.
3. Remove the filter.
4. Install a new filter.
5. Pay attention to the sequence of filters.

MAINTENANCE AND CLEANING

Under poor air quality, there will be a lot of dust in front of the control panel, which needs to be cleaned up.

1. Disconnect the power supply before cleaning.
2. 0pen the cover next to the button on the machine control panel.
3. Use a brush to dust the lid. Then put the lid on and plug it in.

INSPECTION AND 1ROUBLESH0011NG

• The display shows “000”, the motor stops working, and the PM2.5 indicator light shows red, which means a problem with the PM sensor. Maintenance and cleaning are required.
• lf the machine is short-circuited and there is a power outage at home, the overload protector will cut off the circuit to protect the machine.

POWER-OFF PROTECT”OON TREATMENT

1. Unplug the machine.
2. Press the overload protector button back to its original position by hand.
3. Plugin the power supply and start-up.

LIMITED WARRANTY

Purisystems Warranty Steps:

1. Upon receiving this item, visit www.purisystem.com and fill out the warranty registration form. The order number is required to submit a warranty claim.
2. To request warranty service, contact sales@purisystems.com.
3. After receiving the warranty service request, our customer support team will investigate the issue. Here, will be determined if a Return authorization is necessary.
4. If the damage to the machine is proven to be one of the warranty exclusions (Page 10), PuriSystems will not be responsible for all the associated repair and shipping costs. The eligibility of a replacement unit will also be voided.
5. If the damaged unit that can no longer be fixed is within the warranty period, Purisystems will handle all the cost to send a brand-new replacement unit.
6. When the unit is repaired or replaced, the original warranty period carries over to the repaired or new unit. No warranty extensions will be offered.

Warranty Exclusions

DAMAGE DUE TO THE FOLLOWING IS NOT covered under warranty  Acts of Nature- including but not limited to Flooding Fire Water damage Hurricane/storm damage IMPROPER USAGE- Including but not limited to: Misuse, abuse, or tampering whether intentional or accidental Improper installation Improper voltage Failure to follow instructions 3. Corrosion 4. Freezing 5. Any additional costs due to changes in laws or building codes 6. Freight charges 7. Any costs due to lost profit or delay 8. Damage to property 9. Cause beyond control 10. Consumable parts, including but not limited to: Filters Batteries Power cords Valves  Switches Rubber parts11. Direct, indirect, collateral or inconsequential damages of any kind THE WARRANTIES AND LIABILITIES SET FORTH ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, IN LAW OR IN FACT, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE. Purisystems’ total liability, regardless of nature of claim shall not exceed the original purchase price of the product. If a product or component is replaced while under warranty, the applicable warranty period shall not be extended beyond the original warranty time period.The foregoing shall constitute the total liability of the seller in the case of defective performance of all or any of the equipment or services provided to Buyer. Buyer agrees to accept and hereby accepts the foregoing as the sole and exclusive remedy for any breach or alleged breach of warranty by Seller.Any dishonesty or fraud in connection with Purisystemswarranty thoroughly voids all warranty policies. Purisystems expressly reserves the right to pursue legal action in the event of dishonesty, fraud, or attempted fraud.

Wiring Diagram

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>