Eurotech Lighting SLIMBATTEN36W4K Sarah 4FT Slim 4K LED Batten Instruction Manual
- June 12, 2024
- eurotech lighting
Table of Contents
Eurotech Lighting SLIMBATTEN36W4K Sarah 4FT Slim 4K LED Batten
Product Information
- Model: SLIMBATTEN
- Code: SLIMBATTEN36W4K, SLIMBATTEN50W4K, SLIMBATTEN50W6K
- Dimensions
- SLIMBATTEN36W4K: 1200L x 80W x 43D mm
- SLIMBATTEN50W4K: 1500L x 80W x 43D mm
- IP Rating: IP40
- Kelvins
- SLIMBATTEN36W4K: 4000K
- SLIMBATTEN50W4K: 4000K
- SLIMBATTEN50W6K: 6500K
- Lumens
- SLIMBATTEN36W4K: 4200lm
- SLIMBATTEN50W4K: 5900lm
- SLIMBATTEN50W6K: 6000lm
- Material: Aluminium + Iron + PC
Installation Instructions
- Pre-drill two 6mm diameter holes on the intended mounting surface, ensuring a depth of 30mm or more for each hole and a distance of no more than 1.1 metres apart. Gently knock the provided plastic expansion tubes provided into the pre-drilled holes, ensuring the plastic tubes are flush with the mounting surface.
- Take the flush mounting clips and line up the fixing holes to the pre-drilled location holes on your mounting surface. Fix both flush mounting clips using the screws provided.
- Open the back terminal cover plate of the termination box to find the connection terminal and interconnect mains power supply cables with the connection terminal. Make sure that all connections are secure and properly tightened.
- Clip the slim LED batten onto the flush mounted clips. Ensure installation is correct before switching on the fitting to test.
Please refer to the switching capacity specifications of this fitting when application is alongside technology such as sensors and dimmers. Please refer to our website for more information (www.eurotechlighting.co.nz), or contact a Eurotech Lighting Consultant on: 09 818 6039
Safety Instructions
- The light source contained in this luminaire shall only be replaced by the manufacturer or this service agent or a similar qualified person.
- This LED luminaire must be installed by a licensed electrician ONLY following all local regulations.
- Ensure that the cables will not be squeezed or damaged by sharp edges.
- Clean the light with a soft cloth and a standard PH-neutral detergent.
- Misuse of/or changes to the appliance shall void all warranties.
- Do not install on a surface that is not suitable or deformed.
- Do not install on or above a surface with a high temperature.
- There should not be any materials that are corrosive, explosive.
For detailed specification, please go to our website (www.euroechlighting.co.nz)
All installations must be carried out by a qualified electrician following
local regulations. Make sure that the power is switched off before
installation. Please read and follow the ‘Installation instructions’ and
‘Safety instructions’ sections carefully before commencing installation.
Installation of this model can change from time to time please read
instructions every time before installation. For detailed specification,
please go to our website
eurotechlighting.co.nz
SPECIFICATION
| Code: | Dimensions (mm): | IP Rating: | Kelvins: | Lumens: | Material: | Watts: |
|---|---|---|---|---|---|---|
| SLIMBATTEN36W4K | 1200L x 80W x 43D |
IP40
| 4000K| 4200lm|
Aluminium + Iron
+ PC
| 36W
SLIMBATTEN50W4K|
1500L x 80W x 43D
| 4000K| 5900lm|
50W
SLIMBATTEN50W6K| 6500K| 6000lm
Product Information
Installation Instructions
- Pre-drill two 6mm diameter holes on the intended mounting surface, ensuring a depth of 30mm or more for each hole and a distance of no more than 1.1 metres apart. Gently knock the provided plastic expansion tubes provided into the pre-drilled holes, ensuring the plastic tubes are flush with the mounting surface.
- Take the flush mounting clips and line up the fixing holes to the pre-drilled location holes on your mounting surface. Fix both flush mounting clips using the screws provided.
- Open the back terminal cover plate of the termination box to find the connection terminal and interconnect mains power supply cables with the connection terminal. Make sure that all connections are secure and properly tightened.
- Clip the slim LED batten onto the flush mounted clips.
Ensure installation is correct before switching on the fitting to test.
Please refer to the “switching capacity specifications” of this fitting when application is alongside technology such as sensors and dimmers. Please refer to our website for more information (www.eurotechlighting.co.nz), or contact a Eurotech Lighting Consultant on: 09 818 6039
Safety Instructions
Read these instructions carefully before commencing installation.
- The light source contained in this luminaire shall only be replaced by the manufacturer or this service agent or a similar qualified person.
- This LED luminaire must be installed by a licensed electrician ONLY following all local regulations.
- Ensure that the cables will not be squeezed or damaged by sharp edges.
- Clean the light with a soft cloth and a standard PH-neutral detergent.
- Misuse of/or changes to the appliance shall void all warranties.
- Do not install on a surface that is not suitable or deformed.
- Do not install on or above a surface with a high temperature.
- There should not be any materials that are corrosive, explosive.
For detailed specification, please go to our website eurotechlighting.co.nz
References
- Eurotech Lighting | Interior & Exterior Lighting NZ
- Eurotech Lighting | Interior & Exterior Lighting NZ
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>