BOCCI 21.3 Cluster 3 Raw Porcelain Pendant Light Instruction Manual
- June 4, 2024
- BOCCI
Table of Contents
Raw Porcelain Pendant Light
Instruction Manual
| adjustable up to 3000 10’)
standard adjustable up to 30500 (100’) custom
---|---
PENDANTS:| three
---|---
MOUNTING:| brushed nickel canopy 152mm (6”) in diameter x 32mm
LAMPING:| 1.5w LED or 20w xenon
COAX:| adjustable. 3000mm (10’) standard / up to 30500mm
MATERIALS:| porcelain, borosilicate glass, braided metal coaxial cable,
WEIGHT:| approximately 1.8kg (4lb)
POWER SUPPLIES| integral
DESCRIPTION
21.3 is a clustered confi duration of three 21 pendants hung from a round
canopy. The pendants are designed to hang in a random confi duration, the
result is an ambient installation or fi eld of light. The pendant drop lengths
on this light fi fixture are adjustable up to the specifi ed maximum.
Inspired by the sporadic, discordant arrangement of barnacles on a rock
surface, the 21 is fabricated from thin sheets of porcelain wrapped around a
trumpet-shaped borosilicate diffuser. Each diffuser houses a low voltage lamp.
A strong contrast is established between the organically distributed soft
light passing through the white porcelain skin and the sharp, crisp light
passing through the borosilicate glass diffuser.
NOTES
+ Purchase replacement lamps online at
www.bocci.com/shop/bulbs
+ Unless otherwise noted when ordering, all chandeliers will be outfitted to
be xenon compatible.
+ As an alternative to a built-in power supply, Bocci recommends mounting
power supplies remotely in an easily accessible and hidden location for easeof
long-term maintenance.
US patent # US D556,361
Worldwide patents issued and pending
Made in Vancouver, Canada
Very carefully uncoil the braided coaxial cable in a spool-like manner. Insert
your index fingers into opposite sides f the roll then rotate your fi fingers
around each other to enroll the coaxial cable. Use patience: allow the cable
to ncoil ompletely to avoid kinks.| Determine the overall drop for the
pendant fixture.
Thread the coaxial cables through the canopy, use a 2mm Allen key to loosen
the setscrew in the canopy and gently feed the cable through until you have
reached your desired drop length. Use the Allen key to tighten the setscrew to
hold the strain relief and secure the coaxial cable at its new length.
perform a gentle tug test to ensure it is secure.
DO NOT OVER-TIGHTEN. Note: The strain relief is a black plastic collar around
the coaxial cable. There is a single-slot opening on the side of the strain
relief component. It is essential that this opening is oriented at 90 degrees
to set the screw chamber. There can be no contact between the et screw and the
cable. RISK OF ELECTRIC SHORT!| Xenon (110V) or LED: connect the black wire
to black nd white re to where. Xenon (230V): connect black wire to brown wire
and white wire to blue wire. Connect the coaxial cable to the open slots in
the terminal block on the 12V side of the power supplies. ensure that the
braided outer wires are all connected to one 12V output wire and all manner
insulated wires are connected to the other or a short will occur. Once all
coaxial connections are made, lift the fi ture into position nd connect the
line voltage to the open slot in the appropriate terminal block.
The client is responsible to ensure fasteners are attached to a robust
structural substrate. Tuck the power supply and
wiring into the canopy. Line up the fastener holes or connect directly to the
structural ceiling surface using the fasteners provided. Turn power to fixture
on.| Bocci LED or xenon lamps are included. Lamping is power supply specifi c.
Plug the lamp into the socket. Do not touch the lamp with your bare hands.
Ensure power to the lamp is working correctly. Thread the coaxial cable
through the shade, followed by the borosilicate diffuser, and the cap, and
finally close off the diffuser with the diffuser gasket.
Cleanfi fingerprints from surfaces.
Vancouver
sales@bocci.com
www.bocci.com
Berlin
europe@bocci.com
www.bocci.com
US patent # US D556,361
Worldwide patents issued and pending.
Made in Vancouver, Canada
LOW VOLTAGE LUMINAIRE
E476186