KICHLER 52544BK Bretta Traditional Hallway Flush Mount Ceiling Light with Satin Etched Glass Instruction Manual
- June 12, 2024
- KICHLER
Table of Contents
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
FIXTURE DIAGRAM
- MOUNTING STRAP/ HEX NUTS/ THREADED PIPE ASSEMBLY
PARTS LIST
[A] Canopy
[B] Lockup Knob
[C] Hex Nut
[D] Mounting Strap
[E] Outlet Box (not supplied)
[F] Strap Mounting Screw
[G] Threaded Pipe
[H] Glass
CAUTIONS
CAUTION - RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fusebox before
starting and during the installation.
WARNING:
- This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.
CLEANING:
- Always be certain that electric current is turned off before cleaning.
- Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.
INSTALLATION INSTRUCTIONS
1. Take threaded pipe [G ] from parts bag and screw on one hex nut [C] as shown.
2. Screw threaded pipe into mounting strap [D] until hex nut prevents the
threaded pipe from screwing in any further.
NOTE: Mounting strap must be positioned with extruded thread facing into
outlet box [E].
3. Screw second hex nut onto end of threaded pipe protruding from back of
mounting strap. Hex nut should be screwed onto threaded pipe until mounting
strap prevents the hex nut from screwing on any further.
NOTE: Threaded pipe must protrude out the back of mounting strap far
enough to fully engage second hex nut. If necessary, adjust the position of
first hex nut on threaded pipe to ensure full engagement of second hex nut.
4. Screw third hex nut onto threaded pipe approximately 1/2 inch (12.7 mm) as shown.
5. Attach mounting strap to outlet box using the strap mounting screws [F]. Mounting strap can be adjusted to suit position of fixture.
6. Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw, and
thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire from
outlet box under cupped washer and green ground screw, and thread into
mounting strap.
If fixture is provided with ground wire, connect fixture ground wire to outlet
box ground wire with wire connector after following the above steps. Never
connect ground wire to black or white power supply wires.
- OUTLET BOX GROUND
- FIXTURE GROUND
- GREEN GROUND SCREW
- WIRE CONNECTOR
- DIMPLES
- CUPPED WASHER
7. Make wire connections. Reference chart below for correct connections and wire accordingly.
Connect Black or Red Supply Wire to:
| Connect White Supply Wire to:
---|---
Black|
White
*Parallel cord (round & smooth)
| *Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer|
Clear, Brown, Gold or Black with Tracer
Insulated wire (other than green) with copper conductor
|
Insulated wire (other than green) with silver conductor
*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)
- Neutral Wire
8. Raise canopy [A] to ceiling, carefully passing threaded pipe attached to mounting strap through center hole in canopy, and adjust third hex nut so that it meets the bottom of canopy.
9. While holding canopy in place, screw lockup knob [B] onto threads protruding through hole in center of canopy. Tighten to secure.
10. Install recommended bulbs (not supplied).
11. Carefully lift glass [H] up to installed canopy. While gently pushing glass up against canopy, rotate glass clockwise until the glass locks into place in canopy.
REV 18-FEB-2022 For warranty information please visit: kichler.com/warranty
IS-52545-US