KICHLER 55147PN Rosalind Vanity Light Instruction Manual

55147PN Rosalind Vanity Light
Instruction Manual

FIXTURE DIAGRAM

PARTS LIST
[A] Mounting Strap
[B] Canopy
[C] Strap
Mounting
Screw (Qty. 2)
[D] Outlet Box
(Not supplied)
[E] Mounting
Screw (Qty. 2)
[F] Socket Ring
[G] Shade
[H] Flat Steel Ring
[I] Socket

CAUTIONS
CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fuse box before starting and during the installation.
WARNING:

1. This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING

• Always be certain that electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

1. Attach mounting strap[A] to outlet box[D] using the strap mounting screws[C]. Mounting strap can be adjusted to suit position of fixture.
   NOTE: Mounting strap[A] should be mounted with the mounting screw holes in the 12 and 6 o’clock position.

2. Grounding instructions: (See Illus. a or b).
   a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
   b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
   If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.

3. Make wire connections. Reference chart below for correct connections and wire accordingly.
   Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
   ---|---
   Black| White
   Parallel cord (round & smooth)| Parallel cord (square & ridged)
   Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
   Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)

4. Push fixture to wall, carefully aligning mounting screw holes in the top and bottom of mounting strap[A] with mounting screw holes in the top and bottom of canopy[B].
   NOTE: Fixture can be mounted with shade[G] in the up or down position. Make sure all wires are inside canopy[B] and do not get pinched between mounting strap and canopy or wall and canopy of fixture.

5. Screw two (2) mounting screws[E] into the holes in the canopy and mounting strap to attach fixture to wall. One at the top and one at the bottom. Tighten to secure.

6. Carefully slip shade[G] over socket[I]. Make sure shade is fully seated in socket base cup.

7. While holding shade in place on socket base cup, carefully slip flat steel ring[H] over the socket, and screw socket ring[F] onto threads on outside of socket. Tighten socket ring to secure shade. DO NOT OVERTIGHTEN.

8. Insert recommended bulb (not included).

REV 8-MAR-2022
For warranty information please visit: kichler.com/warranty
IS-55147-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST

References

• Kichler® Warranty Information | Kichler Lighting

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>