SENCOR SFE 2310WH Desktop Fan User Manual
- June 16, 2024
- SENCOR
Table of Contents
SENCOR SFE 2310WH Desktop Fan
Important safety instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
-
This appliance may be used by children 8 years of age and older and by persons with physical or mental impairments or by inexperienced persons, if they are properly supervised or have been informed about how to use the product in a safe manner and understand the potential dangers. Cleaning and user maintenance must not be performed by children unless they are older than 8 years of age and under supervision. Keep this appliance and the power cord out of reach of children that are younger than 8 years of age. Children must not play with the appliance.
-
Before connecting the appliance to a power socket, check that the rated voltage on its rating label matches the electrical voltage in the power socket.
-
Connect the appliance only to a properly grounded socket.
-
The appliance is designed for use at home, in offices and similar types of areas. Do not use it in very dusty or humid rooms such as laundries or bathrooms, in areas where chemical or explosive substances are stored, in industrial surroundings or outdoors.
-
Do not place the appliance in the vicinity of an open flame or appliances that are sources of heat.
-
Do not place the appliance on unstable surfaces such as carpets with very long and thick fibres. Only place the appliance on a clean, even, dry and smooth surface.
-
Only use original parts to assemble the appliance. Before starting to assemble the appliance, make sure that it is turned off and disconnected from the power socket.
-
Prior to connecting the appliance to a power socket, make sure that the appliance is correctly assembled according to the instructions in this user’s manual. Do not start the appliance without the protective grills properly installed.
-
Do not cover the appliance with any items while it is running. Never insert fingers or other items through the protective grille.
-
Avoid coming into contact with the rotating parts of the appliance.
-
Never submerge the appliance or its power cord in water or any other liquid and do not wash it under running water.
-
Make sure the power cord does not hang over the edge of a table or that it is not touching a hot surface.
-
Always turn off the appliance and disconnect it from the power socket when leaving it without supervision, when not using it and before moving, disassembling or cleaning it.
-
Disconnect the appliance from the power socket by pulling on the plug, never pulling on the power cord. Otherwise, this could damage the power cord or the socket.
-
If the power cord is damaged, it must be replaced by an authorised service centre or by another similarly qualified person, this will prevent the creation of a dangerous situation. It is forbidden to use the appliance if it has a damaged power cord.
-
Do not use the appliance if it is not working correctly, if it has been damaged or has been submerged in water. To avoid a hazardous situation arising, do not repair the device yourself or modify it in any way. Have all repairs performed at an authorised service centre. By tampering with the appliance, you risk voiding your legal rights arising from unsatisfactory performance or quality warranty.
-
Prior to using this appliance, please read the user’s manual thoroughly, even in cases, when one has already familiarised themselves with previous use of similar types of appliances.
Only use the appliance in the manner described in this user’s manual. Keep this user’s manual in a safe place where it can be easily retrieved for future use. -
We recommend saving the original cardboard box, packaging material, purchase receipt and responsibility statement of the vendor or warranty card for at least the duration of the legal liability for unsatisfactory performance or quality. In the event of transportation, we recommend that you pack the appliance in the original box from the manufacturer.
DESCRIPTION OF THE APPLIANCE
A1 Front protective grill
A2 Fan blades with a diameter of 23 cm
A3 Nut for fastening the rear protective grill
A4 Rear protective grill with fastening clamps and a carry handle
A5 Motor unit shaft
A6 Horizontal oscillation toggle switch
A7 Motor unit with adjustable vertical tilt angle
A8 Panel with control buttons 0 – off, 1 – low speed, 2 – high speed
A9 Base
Note:
The accessories include a screw and a nut for joining the protective grills.
BEFORE ASSEMBLING
- Take the appliance and its accessories out of the packaging materials. Before disposing of the packaging materials, make sure that no part of the appliance is missing.
ASSEMBLING THE APPLIANCE
-
Before starting to assemble the appliance, make sure that it is turned off and disconnected from the power socket.
-
Insert the control panel A8 from above into the base A9 and make sure that it is properly seated inside. Grasp the fan under the motor unit A7 and turn it upside down. Turn the wing nut located underneath the control panel A8 by 90° to secure the panel A8 to the base A9 ( see fig. B ). Turn the fan back over to the operating position and stand it on a straight, clean, dry, stable and smooth surface.
-
Place the rear protective grill A4 against the front side of the motor unit A7 so that the handle is above the motor unit A7 and that the alignment tabs on the front side of the motor unit A7 slide into the respective holes in the rear grill A4. Place the nut A3 on to the shaft A5 and screw it in clockwise to secure the rear protective grill A4 to the motor unit A7. Before tightening the nut A3, make sure that the rear grill A4 has not moved and that the alignment tabs are still in the respective holes.
-
On to the shaft of the motor unit A5 put on the fan blades A2 so that the shaft A5 properly slides into the centre part of the fan blades A2. Push the fan blades A2 towards the motor unit A7 all the way. Now check that the fan blades A2 turn freely.
-
Release the clamps along the perimeter of the rear protective grill A4. Place the front protective grill A1 against the rear protective grill A4 so that the front grill Al fits into the alignment hook in the bottom part of the rear protective grill A4 and that the screw holes at the top of both grills are aligned.
Fasten the released clamps along the perimeter of the grills. To ensure a strong connection of the two grills, into the holes at the top of the grills it is necessary to screw in the supplied screw and secure it with the nut.
OPERATING THE APPLIANCE
Setting the speed and turning off the fan
-
Locate the fan on an even, dry and smooth surface within reach of a power socket. Connect the power cord to a power socket.
To set the air flow speed, use the buttons on the control panel A8. The functions of the control buttons are described below:
0 -turn off the fan;
1 – set a low air flow speed;
2 – set a high air flow speed. -
When you have finished using the fan, always turn it off and disconnect it from the power socket.
Setting horizontal oscillation
- The horizontal oscillation of the motor unit A7 can be set using the toggle switch A6. To start the horizontal oscillation, push the toggle switch A6 down. The motor unit A7 will oscillate from side to side at an angle of approximately 90°.
- To turn off the oscillation, pull the toggle switch A6 up. This will turn off the oscillation.
Setting the vertical tilt angle of the motor unit
- Before setting the vertical tilt angle of the motor unit A7, first turn off the fan. Set the desired angle of the motor unit A7 and then you may start the fan again.
Note:
The motor unit A7 may only be tilted up and down in a limited range. Do
not set the tilt angle of the motor unit A7 by force.
CLEANING AND MAINTENANCE
- Keep the fan clean. Before cleaning, turn the fan off and disconnect the power cord from the power socket. Do not disassemble the fan.
- To clean the outer surface of the fan, use a clean, lightly dampened cloth. Then wipe everything so that it is thoroughly dry. Make sure that no water enters the motor unit A7 or into the control panel A8 while cleaning.
- Do not submerge the appliance or its power cord in water and do not wash it under running water.
- For cleaning do not use steel wool, cleaning products with an abrasive effect, petrol and other solvents.
STORAGE
If you will not be using the fan for an extended period of time, store it in a clean, dry place.
TECHNICAL SPECIFICATIONS
Rated voltage range …………………….220-240V
Rated frequency ………………………… 50 Hz
Rated power ………………………………….. 25 W
Electrical shock protection class ……….II
Noise level …………. 51 dB(A)
Maximum fan flow rate ………….. 13.37 m3/min
Service value ……………… 0.68 (m3/min)/W
Maximum air velocity …………… 2.93 m/s
Measurement standard for service value ……………………….. IEC 60879:1986, EN
50564:2011, EN 60704-2-7:1998, EN 60704-1 :2010
Contact details for obtaining more information …………….. FAST LR, a. s.,
Cernokostelecka 1621, 251 01 i\icany, Czech Republic
The declared noise emission level of the appliance is 51 dB (A), which represents a level A of acoustic power with respect to a reference acoustic power of 1 pW.
Explanation of technical terminology
Safety class for electrical shock protection:
Class II – electrical shock protection is provided by double or heavy-duty
insulation.
We reserve the right to change text and technical specifications.
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at a site designated for waste in your municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on products or original documents means that used electric or
electronic products must not be added to ordinary municipal waste. For proper
disposal, renewal and recycling hand over these appliances to determined
collection points.
– Alternatively, in some European Union states or other European countries you
may return your appliances to the local retailer when buying an equivalent new
appliance.
Correct disposal of this product helps save valuable natural resources and
prevents potential negative effects on the environment and human health, which
could result from improper waste disposal. Ask your local authorities or
collection facility for more details.
In accordance with national regulations penalties may be imposed for the
incorrect disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic appliances, ask your retailer
or supplier for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this
product, request the necessary information about the correct disposal method
from the local council or from your retailer.
This product meets all the basic requirements of EU directives related to it.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>