NEEWER RC-L 2.4G Multi Function Remote Controller Instruction Manual

June 12, 2024
NEEWER

NEEWER RC-L 2.4G Multi Function Remote Controller

NEEWER-RC-L-2.4G-Multi-Function-Remote-Controller-
product

Product Information

The product operates at a frequency of 2432MHz.

Product Usage Instructions

  1. Make sure the product is properly connected to the power source.
  2. Ensure that the product is placed in an open space with minimal obstructions.
  3. Turn on the product by pressing the power button.
  4. Wait for the product to initialize and establish a connection.
  5. Once the product is ready, follow the specific instructions for the intended use.
  6. When finished using the product, turn it off by pressing the power button again.
  7. Disconnect the product from the power source.

Safety tips:
To prevent any damage to the product or to your personal injury, please read the caution carefully.

The product structure

NEEWER-RC-L-2.4G-Multi-Function-Remote-Controller-
fig-1 NEEWER-RC-L-2.4G-Multi-Function-
Remote-Controller-fig-2

The display panel

NEEWER-RC-L-2.4G-Multi-Function-Remote-Controller-
fig-4

Key function

Screen backlight / lock button

Display panel backlight switch
In the power-on state, short press the screen backlight/lock button once, the screen backlight will light up. After the screen backlight is on, the backlight will automatically turn off when there is no key operation for 10 seconds.

Lock button
In the power-on state, long press the screen backlight/lock button for 3 seconds, the screen   lit icon (figure 4.1-A), all the buttons on the remote control all locked at this time. Key lock state, long press the lock button for 5 seconds can remove key lock, at this time the icon disappears from the screen.NEEWER-RC-L-2.4G-Multi-Function-Remote-Controller-
fig-7

Focus/shoot button
When the remote control is turned on, and the remote control is wired to the camera or wirelessly connected to the handle is good., Press the button lightly, the camera will focus, then complete press the button , the camera will shoot Long press the button for 5 seconds , will entre the shuttle B mode, the panel will display an icon B and B shutter timing. Press the B button again, and exit B shutter mode icon on he screen. Return to clock timer.

Start/stop buttons

Start
In setting up good timing sequence parameters, press the button timing program began to run.

Stop
In the process of timing program is running, press the button timing applications will stop running. Stop running time program, press button again, timing program will run from the beginning again.

Infrared shooting button
When the camera’s shooting mode to remote mode, press the U button on the remote control, remote control will launch the infrared signal, remote camera photograph directly. When U button pressed, the indicator light on the remote control is green. On the market, these infrared cameras can apply to the Nikon, Canon, SONY, Olympus, and Pentax brand with infrared cameras, such as SLR, and micro single cameras.

SET Key
When the key is not locked, press the SET key to enter the corresponding setting options. When the parameter value flashes, press the SET key to exit the setting.

Menu Key

In setting status, use the to swith the parameters.
In setting status, use the to increase or decrease the parameters.

Function description

Clock setting
When use this product for the first time, 12:00:00 is display on the panel. Please press the SET key to adjust the clock. When the Clock icon blinks, press the up or down key to adjust. When the clock flashes, press the left or right key to enter the minute setting. Press the left or right key again to enter the clock setting. After setting, press the SET key to exit.

Remote control channel settings
In the boot interface, press the up button to enter the channel setting interface, press the SET button, the ones place of the value after CH flashes, press the up and down buttons to adjust the value, and press the left and right buttons to move between the ones and tens Switch, press SET to exit the setting.

The remote control channel is matched with our RC series handle
After the remote control is turned on, set the channel value of the remote control to the channel value you want. The RC series handles of our company are installed with batteries, and then when the handle function switch is ON, press the focus on the handle and the shutter button once. At this time, the remote control and the handle are paired successfully. If you want to configure multiple handles for a single channel, just continue to power on the RC series handles that need to be paired, turn on the handle function switch, and press the focus and shutter buttons once. If you want to use the remote control to control multiple handles separately, you only need to pair one handle, change the remote control channel, and then pair the other handle to complete multiple channels to match multiple cameras. If you want to control the handle of the corres- ponding channel, you only need to adjust the channel of the remote control to the channel when the handle is paired.

Use of connector socket
Prepare the required cable, insert one end of the 2.5mm audio plug of the cable into the cable socket of the remote control, and then insert the other end of the cable into the corresponding camera shutter cable interface. Use as a wired timer shutter release.

Setting and use of timing interface

In the clock interface, press the down key once or press the up key twice to enter the timing interface. At this time, the DELAY icon is blinking. Press the left and right to choose between the LONG / INTUL / NUM options. When any option icon is flashing, press the SET key to enter the parameter setting. Press the left and right keys to switch between various param- eters. Press the up and down keys to adjust the parameter value. After setting, press the SET key to exit.

The timer parameters and timing

Timing parameter

NEEWER-RC-L-2.4G-Multi-Function-Remote-Controller-
fig-15

Timing working process

NEEWER-RC-L-2.4G-Multi-Function-Remote-Controller-
fig-16

Product size

NEEWER-RC-L-2.4G-Multi-Function-Remote-Controller-
fig-17

Technical specifications

NEEWER-RC-L-2.4G-Multi-Function-Remote-Controller-
fig-18

Caution

  1. Please use the specified battery only, otherwise the product may not be turned on or damaged.
  2. This product has no waterproof function.
  3. Please do not drop, strike the product.
  4. When the battery icon blinks, replace the battery with a new one.
  5. The connector of the product is used to connect the camera shutter cable port to use as a shutter cable. It is forbidden to insert any plug other than the camera cable into the connector, otherwise the product will be damaged.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals