THE HOME DEPOT YMPE-7135777 52 Inch LED Indoor Coffee Ceiling Fan with Light Instruction Manual
- June 12, 2024
- THE HOME DEPOT
Table of Contents
YMPE-7135777 52 Inch LED Indoor Coffee Ceiling Fan with Light
Assembly – Hanging the Fan(continued)
Preparing for mounting
5. Make wiring connections using wire connectors provided as indicated above.
White from house to White from remote receiver marked AC N. Black from house
to Black from remote marked AC L. Connect all green grounded wires to Grounded
wire from House. Make sure that no laments are outside of the wire connector.
6. Lift motor assembly, aligning the keyhole slots with the preassembled screws on mounting plate, and twist clockwise till lock.
Assembly — Attaching the Fan Blades
7.Loosen 2 screws across from each other and remove the other 2 preassembled
screws from side of mounting plate (corresponding to installation step 8 ).
Save screws for tater use.
8. Attach housing onto mounting plate, aligning the keyhole slots on the
housing with the screws on Mounting plate and twist clockwise till tight.
Reinstall the screw removed in step 7. Tighten all screws securely.
9. Install blade with screws provided, aligning each of the holes as shown
and tighten all screws securely. Repeat this process for remaining blades.
Assembly — Attaching the Lights
- Install the light kit fitter, tighten all screws.
- Connect the light kit with motor, put the light kit in the light kit fitter.
- Install the lamp cover as shown
Use of remote control
- ALL OFF:Turn off the lights and fans at the same time
- Fan Control Keys
- F/R:Changing fan run direction(15 sec)
- Timer: It will turn off the light and the fan when the time is over
- Turn on/off the light
- Anti-theft lamp and natural wind
Note: the remote control must match the same code receiver
Remote control wiring diagram
Operation
OPERATING YOUR FAN
Turn on the fan and check the condition of the fan operation.
And make sure that you can control the fan speed and light properly by the
remote control .
The appropriate speed settings for warm or cool weather depends on factors
such as the room size, ceiling height and number of fans.
The slide switch controls the direction of the blades: forward (switch down)
or reverse (switch up).
NOTE: Before reversing the direction of the blade rotation, please wait
untit the fan stops.
A. Warm Weather- Forward
Fan rotates anti-clockwise creating a downward airflow ( delivering a cooling
effect.
Suitable for hot weather condition or air-conditioned condition. A. Winter
Weather- Reverse
Fan rotates clockwise creating an upward airflow moving warm air off the
ceiling areas. This function works best at lower fan speed.
Suitable for cold weather or air-conditioned condition.
Fans Balance
Slide the balancing clip on the trailing edge of any blade, halfway between
the holder and tip. Run the fan to check the wobble.
If the wobble persists, repeat with each blade, noting which one most reduced
the wobble.
Slide the clip in small increments away from the center of that blade. Move
the clip, operate the fan, then move it again until you eliminate as much
wobble as possible.
Stick the adhesive-backed balancing weight on the top center of the blade
directly in line with the balancing clip.Add more weight if needed to get a
smooth-running fan.
Care and Cleaning
WARNING: Make sure the power is off before cleaning your fan.
- Because of the fan’s natural movement, some connections may become loose Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
- Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor, or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free doth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
- You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
- You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.
Troubleshooting
| Problem | Solution |
|---|---|
| The fan will not start. | 0 Check the main and branch circuit fuses or |
breakers.
CI Check the line wire connections to the fan and switch wire connections in
the switch housing.
The fan is noisy.| 0 Ensure all motor hausig screws are snug.
0 Ensure the screws that attach the fan blade bracket to the motor hub are
tight.
0 Ensure the wire nut annefions are not ratting against each other a the
interisr wall of the switch housing. 0 Aesw a 24—hour “breaking in period.
Most noises associated with a new fan disappear during this time.
0 If you areusing theCeiling Fan light Idertsure the screws seaming the
glassware sretight.Check that the fight 0 buts are also secure.
0 Ensure the canopy is a short distance from the ceiling.11 should not touch
the ceiling.
0 Ensure your outlet box is secure and rubber isolator pads wereused between
the mounting Pate and outlet box.
The fan wobbles.| 0 Please check and follow the instructions: Chapitre No.13
an balance on page 12.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>