Solis 1019 Perfect Coffee Machine User Guide

: June 12, 2024
: solis

Table of Contents

Solis 1019 Perfect Coffee Machine
Product Information: Solis Grind & Infuse Perfetta Type 1019
Product Usage Instructions
GRIND & INFUSE PERFETTA
IMPORTANT SAFETY PRECAUTIONS
CONTENTS
APPLIANCE DESCRIPTION
INSTALLATION
MAKING AN ESPRESSO
STEAMING MILK
USING THE HOT WATER FUNCTION
MAINTENANCE
REPLACING THE WATER FILTER CARTRIDGE
USING THE BREWING HEAD CLEANING CYCLE
DESCALING
TECHNICAL SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Solis 1019 Perfect Coffee Machine

Product Information: Solis Grind & Infuse Perfetta Type 1019

The Solis Grind & Infuse Perfetta Type 1019 is a coffee machine that grinds and brews coffee beans for a perfect cup of coffee. The machine has a built-in grinder that grinds the coffee beans to your desired coarseness and then brews it directly into your cup. It has a water tank capacity of 8 cups and a milk frother for making cappuccinos and lattes. The machine also has a hot water function for making tea or other hot beverages.

Product Usage Instructions

Step 1: Safety Precautions

Read the safety instructions in the user manual before using the machine.
Make sure the machine is placed on a flat and stable surface.
Do not touch hot surfaces of the machine while in use.
Keep the machine away from children and pets.

Step 2: Machine Setup

Fill the water tank with fresh, cold water.
Plug in the machine and turn on the power with the on/off button.
Select the water hardness level by turning the selector to position A, B, or C, depending on your water hardness.
Insert the double-cup filter or the single-cup filter into the portafilter handle, depending on how much coffee you want to make.

Step 3: Grinding and Brewing Coffee

Add coffee beans to the bean hopper, and adjust the grind size using the grind regulator if necessary.
Place your cup under the spout, and press the single or double cup button to start brewing.
The machine will automatically grind and brew the coffee into your cup.

Step 4: Using the Milk Frother

Fill a milk jug with cold milk, and place it under the steam wand.
Turn on the steam function by pressing the steam button.
Submerge the steam wand into the milk, and froth the milk to
your desired texture.

Step 5: Cleaning and Maintenance

Empty the drip tray and the used coffee grounds after each use.
Clean the portafilter, milk jug, and steam wand after each use.
Run a cleaning cycle with the cleaning tablet once a month.
Replace the water filter cartridge every two months.

Note: Please refer to the user manual for detailed instructions on machine usage, cleaning, and maintenance.

GRIND & INFUSE PERFETTA

You can find a detailed manual, answers to frequently asked questions, and recipes on www.solis.com/manuals

V INTENDED USE

This appliance is intended to prepare various types of coffee with freshly ground beans.
Only use the appliance as described in this manual.
This appliance is intended to be used in household and similar applications such as:
- staff kitchen areas in shops, offices and other working environments;
- farmhouses;
- by clients in hotels, motels and other residential-type environments;
- bed and breakfast type environments and not for commercial use.
This appliance is intended for indoor use only.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Any use of the appliance other than that described in this manual is regarded as misuse and may cause injury, or damage to the appliance and void the warranty.

IMPORTANT SAFETY PRECAUTIONS

General safety instructions

WARNING

Ensure you have fully read and understood the instructions in this user manual before you install or use the appliance. Keep this document for future reference.
Do not use the appliance if a part is damaged or defective. Replace a damaged or defective appliance immediately.
If the power cable is damaged, it must be replaced by the manufacturer, the service agent or similar qualified personnel in order to avoid a hazard.
Only lift the appliance by holding the base. Safety instructions regarding installation

WARNING

Do not drop the appliance and avoid bumping.
Place the appliance on a stable, flat, heat and moisture-resistant surface.
Keep a minimum distance of 20 cm between the appliance and walls, curtains or other materials and objects so the air around the appliance can circulate freely.
Do not place the appliance inside a cabinet when in use.
Do not place the appliance in direct sunlight.
Do not use a timer or a separate remote-control system that switches on the device automatically.
Do not leave the power cable hanging over table edges to prevent the appliance from being pulled down. Make sure that neither the appliance nor the power cord or plug comes into contact with hot surfaces, such as hotplates or a radiator, or that they come into contact with the appliance itself.
Never place the appliance in such a way that it is at risk of falling into water or coming into contact with water resp. other liquids (e.g. in or near a sink).
Never reach for an appliance that has fallen into water or other liquids:
- Always wear dry rubber gloves to unplug the appliance before taking it out of the water.
- Do not start using the appliance again before having it checked for functionality and safety by Solis or a service center authorized by Solis.
Before using the appliance, check that the voltage stated on the type plate of your appliance matches your mains voltage. Do not operate the appliance with a multiway plug adapter.
Do not place the appliance directly under a power outlet.
Switch off and unplug the appliance before moving the appliance.
Fully unwind the power cable before use.

Safety instructions regarding use
WARNING

Children must be supervised to ensure that they not play with the appliance.
Do not operate the appliance with wet hands.
Only use the appliance with the provided accessories or accessories recommended by Solis. Incorrect accessories or misuse can lead to damage to the appliance.
Do not move the appliance when in use.
Do not cover the air vents when the appliance is in use.
Do not place anything on the appliance while it is in use, except for cups for preheating.
Do not leave the appliance unattended when in use.
Always switch off the appliance before disconnecting.
Switch off and unplug the appliance when not in use.
Only use cold tap water in the water tank.
Do not fill the water tank above the MAX marking.
Do not operate the appliance when the water tank is empty.
During operation, only touch the buttons, selectors, or heat-insulated handles. All other parts can get hot.
Be careful when emptying the portafilter directly after use. The appliance and the coffee dregs are still very hot.
Never remove the portafilter during the brewing process.
During or directly after the steaming process, only touch the steam and hot water wand by the thermo-insulated loop. The steaming wand gets hot.
Never point the steam and hot water wand towards people, animals, or moisture-sensitive items. The steam is very hot!
Do not use the appliance when the bean container is empty.
Only fill the bean container with whole coffee beans. Never use ground coffee.
Only adjust the grind size when the grinder is running, to avoid damaging the grinder.
Do not activate the grinder when the lid of the bean container is removed. Safety instructions regarding maintenance
Keep the cleaning tool away from children. Risk of swallowing!
Do not disconnect the appliance by pulling on the cable. Always grasp the connector and pull.
Disconnect the appliance from the power source before service and when replacing parts.
Let the appliance cool down before cleaning.
Never immerse the appliance in water or place it in a dishwasher.
Do not use abrasive chemical cleaning agents such as ammonia, acid or acetone when cleaning the appliance. This can damage the appliance.
Do not use any oils or lubricants on this appliance.
Do not store the appliance in temperatures below 0 °C or above 55 °C.

APPLIANCE DESCRIPTION

(SEE IMAGE A)

Bean container
Cup tray
Portafilter holder
Brewing head
Steaming wand
Drip tray
Grinder unlock button
Water tank
Water filter cartridge
Accessories storage
Power button
Power cable
Milk jug
Test strip
Cleaning brush
Cleaning tool
Rubber insert for cleaning
Tamper
Double cup filter
Single-cup filter
Portafilter
CONTROL BUTTONS (SEE IMAGE B)
Programming button
Filter size selection button
Grind size selector
Filter size indicator
Single-cup extraction button
Double cup extraction button
Steaming function button
Steaming knob
Display
Grind time knob
Portafilter button
Manometer

INSTALLATION

Place the appliance on a stable, flat, and heat and moisture-resistant surface.
Place bean container 1 on the appliance. Rotate until the bean container locks in place.
Plug the power cable e into a power outlet.
Press the power button w to switch on the appliance.
The appliance is ready for use when the cup extraction buttons j k constantly light up white.

BEFORE FIRST USE (WATER FILTER CARTRIDGE)
Before first use, clean the appliance as described in the chapter Daily Maintenance.
If you don’t want to use a water filter, you can leave the appliance on default settings. You can skip the following steps in this chapter.
To place and configure the water filter:

Hold the test strip t briefly in a glass of tap water.
Read the measured water quality on the test strip t.
Rotate the selector at the bottom of the water filter cartridge 9 to the optimal position.
- Position A For use with soft water.
- Position B For use with medium hard water.
- Position C For use with hard water.
Hold the water filter cartridge 9 in a container with water.
Gently squeeze the water filter cartridge 9 to remove air bubbles from the filter.
Insert the water filter cartridge 9 into the bracket in water tank 8 with the selector facing downwards.
Fill the water tank 8 with water up to the MAX marking.
Press the programming button d to enter the settings menu.
Press the steaming function button l to enter the filter settings.
Press the single cup extraction button j to set the filter setting to YES.
Place a container (min. 500 ml) underneath the brewing head 4.
Press the programming button d to exit the settings menu. The rinsing process starts automatically.

MAKING AN ESPRESSO

To make an espresso with freshly ground coffee:

Choose if you want to make one or two espressos.
Place empty cups on the cup tray 2 to preheat the cups.
Check if the water level in the water tank is in between the MIN and MAX indicator.
If not, fill the water tank up to the MAX indicator.
Refresh the water at least once a day.
Fill the bean container 1 with whole coffee beans (max 250 g).
Close the bean container 1 with the lid.
Make sure the hopper gate at the back of the bean container 1 is open.
Place the corresponding cup filter p a in the portafilter s.
When the appliance isn’t used recently, we recommend rinsing the appliance and the portafilter (chapter Daily maintenance).
Press the filter size selection button f to switch to the corresponding filter size.
If needed, adjust the grind size with the grind size selector g. Start with grind setting 12 and then experience to find your personal favourite.
Place the portafilter s into the portafilter holder 3.
Rotate the grind time knob c to adjust the grinding time. The grind time is shown on display 30.
The maximum grind time is 30 seconds. To save the grinding time for the selected filter size, press and hold the filter size button. The filter size button blinks and the appliance beeps twice when the setting is saved.
Press the grind time knob c or the portafilter button v to start the grinding process. The display shows the remaining grind time.
If you need to stop the process before it is finished, press the grind time knob or portafilter button again.
If you need to resume the grinding process, press the grind time knob or portafilter button again within 20 seconds.
To grind without using the grind time presets, you can also press and hold the grind time knob or the portafilter button. The grinder starts grinding and stops when the grind time knob is released.
Shake and pull out the portafilter s of the portafilter holder 3.
Gently tap the portafilter s against the counter to spread out the coffee ground.
Tamp the coffee ground with the tamper 18.
Do not overfill the portafilter. The coffee ground should not make contact with the brewing head when placed to ensure a proper seal.
Remove any coffee ground from the edge of the portafilter s.
Pull the steaming wand 5 to the side.
Insert and rotate the portafilter s into the brewing head 4 (see image C). Make sure the handle is aligned with the CLOSE marking.
6 Make sure the portafilter is firmly installed. If the portafilter does not turn easily in place, remove the portafilter and reduce the amount of coffee ground.
Place one or two cups from the cup tray 2 underneath the spouts of the portafilter. When the cup extraction buttons j k light up you can start the brewing process.
Do not leave the appliance unattended when in use.
Press the corresponding cup extraction button j k to start the process.
During the coffee extraction, the display shows the brewing time.
Check during the process if the manometer b goes from 0 to the optimal range (8 – 12 bar). 4 Quickly double-press the cup extraction button to skip pre-infusion and start immediately with the coffee extraction.
If you need to stop the process before it is finished, press the corresponding cup extraction button again. The maximum brewing time is 60 seconds.
Be careful when emptying the portafilter directly after use. The appliance and the coffee cakes are still very hot.
Remove the portafilter s from the brewing head 4.
Empty the cup filter p a in a knock box or a bin.
When you want to make another espresso, repeat the steps in this chapter. When you are finished we recommend cleaning the appliance (Chapter Daily maintenance).

Solis 1019 Perfect Coffee Machine fig-3

STEAMING MILK

During or directly after use, only touch the rubber handle of the steam and hot water wand. The steaming wand gets hot.

You can use steamed milk for example in a cappuccino or a caffè latte.
You can also use the steaming function for heating chocolate milk or other beverages.

Press the steaming function button 28 to activate the steaming function.
The appliance heats up the steaming function. The steaming function button 28 blinks. When the steaming function is ready, the steaming function button l constantly light up white.
Fill milk jug 13 with milk (max. half a jug).
If the steaming wand is used for dispensing hot water, the steaming wand dispenses water residue before the steaming function activates. For good steamed milk, first dispense the residue before putting the steaming wand into the milk.
Check if the steaming function button 28 constantly lights up white.
Lower the nozzle of the steaming wand 5 a few millimeters into the milk.
Rotate the steaming knob 29 counterclockwise to switch on the steaming wand 5.
Wait until the milk is steamed as desired.
When you cannot touch the side of the milk jug for longer than 3 seconds, the temperature is optimal (approximately 65 °C).
Rotate the steaming knob 29-clockwise to switch off the steaming wand 5.
When not switched off, the steaming function automatically switches off after 2 minutes.
Clean the nozzle of the steaming wand 5 with a damp cloth.
Rotate the steaming knob 29 to remove all milk from the steaming wand 5.
Press one of the cup extraction buttons 26 27 to cool down the steaming function.
The cup extraction buttons 26 27 start flashing. When the cup extraction buttons 26 27 constantly light up white, the system is ready for making coffee.
Pour the frothed milk directly into an espresso.
The steaming wand is hot after use!
Clean the milk jug r with water or in a dishwasher after use.

USING THE HOT WATER FUNCTION

During or directly after use, only touch the rubber handle of the steam and hot water wand. The steaming wand gets hot.

Lower the steaming wand 5 into a cup.
Do not point the tip of the steaming wand directly on the bottom of the cup.
Rotate the steaming knob 29 anticlockwise to dispense hot water from the steaming wand 5.
Press the steaming function button 28 to boost the hot water function.
Rotate the steaming knob 28 clockwise to stop the hot water function.
When not switched off, the hot water function automatically switches off after 2 minutes.
You can also use the hot water function to preheat the cups.

MAINTENANCE

DAILY MAINTENANCE

We recommend doing the following maintenance daily (before first coffee):

Place a container underneath the brewing head 4.
Press one of the cup extraction buttons 26 27 to rinse the brewing head 4.
Dry the brewing head 4 with a cloth.
Rinse the portafilter 21 and the used filters 19 20 with tap water.
Dry the portafilter 21 and the used filters 19 20 with a cloth.
Check if the red floater of the drip tray 6 is visible through the grid.
If so, clean the drip tray 6 (chapter Weekly maintenance).
Repeat this procedure every time you brew a coffee to improve the quality of your coffee.

WEEKLY MAINTENANCE

We recommend doing the following maintenance weekly:

Empty the drip tray 6.
Clean drip tray 6 with water and mild detergent.
Set the grind size selector 24 to COARSE.
Check if the hopper gate at the back of bean container 1 is open.
Place a container under the portafilter holder 3
Press the grind time knob 31 to switch on the grinder and remove excess coffee.
After a few seconds, press the grind time knob 31 again to switch off the grinder.
Set the grind size selector 24 back to the desired position.

MONTHLY MAINTENANCE
We recommend cleaning the appliance every month. To clean the appliance:

Plug in and switch on the appliance.
Set the grind size selector 24 to COARSE.
Close the hopper gate at the back of the bean container 1
Place a container under the portafilter holder 3
Press the grind time knob 61 to switch on the grinder and remove excess coffee.
After a few seconds, press the grind time knob 31 again to switch off the grinder.
Switch off the appliance and remove the bean container 1 (see image E).
Empty the bean container 1.
Always remove the bean container (see image E) first and only then remove the grinder mechanism. Do not take off both parts together and never use excessive force to remove the parts.
Reassemble the bean container 1 (see image F).
Fill the bean container 1 with GRINDZ™ which is available in selected countries.
You can buy GRINDZ™M at your supplier or Solis (art. No. 993.08).
Open the hopper gate at the back of the bean container 1
Place a container under the portafilter holder 3
Switch on the appliance.
Press and hold the grind time knob 31 to switch on the grinder.
When all GRINDZ™ has run through the appliance, release the grind time knob 6) to switch off the grinder.
Close the hopper gate.
Switch off the appliance and remove the bean container 1 (see image E).
Empty the bean container 1
Rinse bean container 1 with warm water and a mild detergent.
Rinse bean container 1 with clean water.
Dry the bean container 1 thoroughly.
Reassemble the grinder and the bean container 1. Make sure all parts lock in place.
Fill the bean container G with coffee beans.
Open the hopper gate at the back of the bean container 1.
Switch on the appliance.
Press and hold the grind time knob 31 to switch on the grinder.
After 20 seconds, release the grind time knob 3) again to switch off the grinder.
Set the grind size selector 24 back to the desired position.
Switch off and unplug the appliance.
Make sure the portafilter is not hot when removing the spout.
Unscrew the spout of the portafilter 21.
Soak the following parts in warm water a and a mild detergent:
- Portafilter 21 (only the metal parts).
- Cup filters 19 20
- Spout
Unscrew the steaming nozzle from the steaming wand 5.
If the nozzle opening is blocked, you can use the pin on the cleaning tablet holder to remove the blockage. If you cannot unblock the nozzle with the pin, rinse the nozzle with warm water and try again.
Rinse the nozzle in warm water.
Gently screw the nozzle back onto the steaming wand 6.
Clean the appliance and the water tank & with a soft and damp cloth.
Dry the appliance and the water tank 8.
Plug in and switch on the appliance.

REPLACING THE WATER FILTER CARTRIDGE

Replace the water filter cartridge when the corresponding alarm is visible.

Switch off and unplug the appliance.
Remove water tank 8 from the appliance (see image G).
Empty the water tank 8 above a sink.
Remove the water filter cartridge 9 from the water tank 8.
Hold the new water filter cartridge 9 in a container with water.
Use the INTENZA water filter cartridge (Art.-no. 700.78) which is available in selected countries.
Gently squeeze the water filter cartridge © to remove air bubbles from the filter.
Rinse water tank 8 with water.
Insert the water filter cartridge into the bracket in the water tank & with the selector facing downwards.
Fill the water tank with water up to the MAX marking.
Insert the water tank 8 into the appliance.
Place a container (min. 500 ml) underneath the brewing head A
Plug in and switch on the appliance.
Press the programming button 22.
Press the single cup extraction button 2 to activate the automatic rinsing cycle.
When the appliance beeps twice and the cup extraction buttons light up white, the appliance is ready for use.

USING THE BREWING HEAD CLEANING CYCLE

Clean the appliance with a cleaning tablet when the corresponding alarm is visible.
For cleaning the brewing head, please use cleaning tablets which are suitable for espresso machines.
For best results, we recommend SOLITABS (Art.-no. 993.02) which is available in selected countries.
To clean the appliance with a cleaning tablet:

Plug in and switch on the appliance.
Place the double cup filter 19 into the portafilter 21.
Place the rubber insert for cleaning 17 into the double cup filter 19 (see image H) and put a SOLITABS cleaning tablet on top.
Insert and rotate the portafilter 21 into the brewing head 4 (see image C). Make sure the handle is aligned with the CLOSE marking.
Place a container underneath the portafilter 21.
Press the programming button 22.
Press the double cup extraction button 27 to start the rinsing procedure.
The procedure has 8 cycles with pauses of 30 seconds. The cycle number and pause time are shown on the display.
Let the appliance cool down.
Remove the portafilter 21 from the brewing head 4.
Remove the rubber insert for cleaning 17 from the portafilter 21.
Before first use, clean the appliance as described in the chapter Daily Maintenance.

DESCALING

Descale the appliance when the corresponding alarm is visible.
For the descaling of the machine, please use a descaling agent which is suitable for espresso machines.
When the descaling alarm shows up, descale the appliance immediately to avoid permanent damage to the appliance. Damage related to limescale is not covered by warranty if the descaling procedure is not performed regularly as described in this chapter. Wipe off spilled descaling solution immediately. The descaling solution can damage the surface of the appliance.

To descale the appliance:

Switch off and unplug the appliance.
Empty the drip tray 6 (see chapter Weekly maintenance).
Remove water tank 8 from the appliance (see image G).
Empty the water tank 8 above a sink.
Remove the water filter cartridge 9 from the water tank 8.
Fill the water tank & with a descaling agent and water. The minimum level required for descaling is 1 itre.
For best results, we recommend Solipol special (Art.-no. 703.02) which is available in selected countries.
Insert the water tank & into the appliance.
Place a large container (> 2.5 l) underneath the brewing head A.
Aim the steaming wand 5 into the container
Plug in and switch on the appliance.
Press the programming button 22.
Press the steaming function button 28 to start the descaling process.
The descaling process takes 20 minutes. During the process:
Rotate the steaming knob 29 anticlockwise when the display shows OP.
Rotate the steaming knob 29 clockwise when the display shows CL.
Remove water tank 8 from the appliance (see image G).
Empty the water tank 8 above sink.
Rinse the water tank 8 multiple times under a tap.
Fill water tank 8 with cold tap water.
Insert water tank 8 into the appliance.
Empty the container and the drip tray 6
Place back the container (step 6 through 7).
Press the steaming function button 28 to start the rinsing process. During the process:
Rotate the steaming knob 29 anticlockwise when the display shows OP.
Rotate the steaming knob 29 clockwise when the display shows CL.
When the rinsing process is finished the appliance beeps twice.
Remove water tank 8 from the appliance (see image J).
Empty the water tank 8 above . sink.
Rinse the water tank 8 multiple times under a tap.
Insert the water filter cartridge 9 into the bracket in water tank 8 with the selector facing downwards.
Fill water tank 8 with cold tap water.
Insert water tank 8 into the appliance.
When the cup extraction buttons light up white, the appliance is ready for use.