METROPOLITAN N7351-790 4-Light Aged Antique Brass Cage Pendant Instruction Manual

METROPOLITAN N7351-790 4-Light Aged Antique Brass Cage Pendant

Product Information

The Fixture Item#N7351-790 is a lighting fixture that comes with a crossbar, ground screw, mounting screw, and four candelabra base bulbs. It is designed to be installed in a ceiling junction box and can accommodate up to 60 watts of power per bulb. The fixture is shipped with its arms placed flat and requires assembly before installation.

Product Usage Instructions

1. Before beginning the installation, shut off the power at the fuse box or circuit breaker.
2. Remove the old fixture and mounting hardware.
3. Unpack the new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
4. Adjust the arms of the fixture to the proper position.
5. Thread the fixture loop onto all threads of the upperassembly.
6. Secure the stems to all threads of the socket assembly and then thread the upper assembly to the stem.
7. Place bolts through holes on top of the frame assembly and tighten with plastic washers and finials.
8. Thread all threads into the ceiling loop with a lock washer and hex nut until snug.
9. Thread the other end of all threads into the crossbar with a lock washer and hex nut until snug. Adjust the length of all threads into the crossbar if necessary.
10. Mount the crossbar assembly to the ceiling junction box using mounting screws. The side of crossbar marked GND must face out.
11. Attach quick link to fixture loop and chain. Determine the correct number of links needed for desired hanging height and use a pair of chain pliers to open one end link of the chain and discard excess chain. Slip lock collar, canopy decorative plate, and canopy over the chain. Attach another quick link to the other end of the chain. Raise the fixture and attach the quick link to the ceiling loop, then close it. Carefully lace the fixture wires through chain links and pull until tight. Feed wires through lock collar, canopy decorative plate, canopy, ceiling loop, and all thread, then pull until tight.
12. Connect the electrical wires as shown in Fig. 3, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to crossbar using the green screw provided.
13. Tuck wire connections neatly into the junction box.
14. Raise the canopy and canopy decorative plate to the ceiling, then secure with a lock collar.
15. Install four candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
16. Turn on the power at the junction box and test the fixture.

Note: The illustration provided in Fig. 1 is for installation purposes only and may or may not be identical to the fixture purchased.

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER. AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

ASSEMBLING THE FIXTURE (FIG. 1 & Fig. 4)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
3. The arms have been placed to lay flat for shipping. Adjust arms to proper position. (See Fig. 4)
4. Thread fixture loop (I) onto all thread (J) of upper assembly (K).
5. Secure stems (M) to all thread (O) of socket assembly (S). Then thread upper assembly (K) to stem (M).
6. Carefully place bolts (N) through holes on top of frame assembly (R). Then tighten with plastic washers and finials (Q).

ASSEMBLING THE FIXTURE (FIG. 2)

1. Thread all thread (C) into ceiling loop (E) with lock washer (Y1) and hex nut (Y2) until snug.
2. Thread other end of all thread (C) into crossbar (A) with lock washer (Y1) and hex nut (Y2) until snug. Note: The length of all thread into crossbar may be adjusted if necessary.
3. Take crossbar assembly and mount to ceiling junction box (Not included) using mounting screws (B) (Size: # 8-32N*L1”). The side of crossbar marked “GND” must face out.
4. Attach quick link (G) to fixture loop (I) and chain (H). Quick link must be completely closed when installed. By measuring, determine correct number of links needed for desired hanging height. Use a pair of chain pliers to open one end link of chain and discard excess chain. Slip lock collar (F), canopy decorative plate (T) and canopy (D) over chain (H). Attach another quick link (G) to other end of chain (H). Raise fixture and attach quick link (G) to ceiling loop (E), then close quick link (G). Carefully lace fixture wires through chain links and pull until tight. Feed wires through lock collar, canopy decorative plate, canopy, ceiling loop and all thread, then pull until tight.

CONNECTING THE WIRE (Fig. 3)

1. Connect the electrical wires as shown in Fig. 3, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to crossbar using the green screw provided.
2. Tuck wire connections neatly into junction box.

COMPLETING THE INSTALLATION (Fig. 1)

1. Raise canopy (D) and canopy decorative plate (T) to ceiling, then secure with lock collar (F).
2. Install (4) four candelabra base bulbs (P) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!) Your installation is now complete. Return power to the junction box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Notice: It is important to use proper chain pliers (not included) To OPEN and CLOSE the chain included with this fixture. Do not open them with other tools that may twist or stress the chain links. It is important to use proper chain pliers like the ones shown in the diagram.
Item# N7351-790 (New. 2022/5/20)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>