CRYSTORAMA 1139-CH-CL-MWP Traditional Crystal 16 Light Crystal Chandelier Instruction Manual

CRYSTORAMA 1139-CH-CL-MWP Traditional Crystal 16 Light Crystal Chandelier

Product Information

The product is a chandelier model #1139-CH-CL-MWP from Crystorama. The chandelier has a damp rating, meaning it is safe to use in areas with some moisture or humidity, such as a bathroom or covered outdoor area. The fixture requires 16 candelabra base bulbs with a recommended wattage of 40 watts and a maximum wattage of 60 watts. LED bulbs are recommended for extended use. The chandelier comes with various parts, including crystal sets, glass vases, metal covers, PVC candle sleeves, upper and lower arms with male plugs, check rings, finial, canopy, collar ring, collar loop, and chain. The product contains lead, which is known to the State of California to cause cancer and/or birth defects or reproductive harm.

Product Usage Instructions

Before installation, place the fixture parts on a soft cloth-covered platform. All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and appropriate local electrical codes. Turn off the power before installation.

1. Attach the upper metal plate and upper arms with the male plug to the center column kit loop.
2. Attach the lower metal plate and lower arms with the male plug to the center column kit loop.
3. Place the bottom bowl, check ring, bottom bobeche (with Ax6), and check ring, in that order, over the bottom distributor box. Secure with the finial.
4. Screw the center column kit onto the bottom column kit.
5. Attach the mounting bar to the outlet box.
6. Decide on the desired hanging height and adjust the chain to the correct length.
7. Raise the fixture up and do the wire connection. Attach the canopy over the mounting bar and secure it with a collar ring.
8. Dress the crystals as illustrated in the detailed illustration.

For extended use, LED bulbs are recommended. Do not exceed the maximum wattage of 60 watts.

ASSEMBLY INSTRUCTION MODEL #1139-CH-CL-MWP

WARNING

• All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes.
• You will need 16- Candelabra Base Bulb 40 Watts recommended 60 Watts Max.
• USE LED BULBS FOR EXTENDED USE
• The fixture is Damp rated

HOW TO INSTALL

Place the fixture parts on a soft cloth-covered platform before installation of the fixture.

1. To install the upper arms, slightly loosen each screw on the upper metal plate. Pull a female plug through a hole in the upper metal plate. Connect the male plug at the end of the upper arm with the female plug that was just pulled. Push the end of the arm with the metal tab through the hole until stopped by the metal tab (this should also push the wires and plugs back inside the metal plate). Twist the metal tab counter-clockwise until both inserts lock onto the loose screws. Tighten the screw securing the arm in place. Repeat for all upper arms.
2. Repeat Step 1 using the Lower metal plate and the lower arms.
3. Place the bottom bowl, check ring, bottom bobeche, and check ring, in that order, over the bottom distributor box. Secure with the finial.
4. Screw the Center column kit onto the Bottom column kit.
5. Attach the mounting bar to the outlet box.
6. Decide the desired hanging height and adjust the chain to the correct length.
7. Raise the fixture up and do the wire connection. Attach the canopy over the mounting bar and secure it with a collar ring.
8. Screw the Center column kit onto the Bottom column kit.
9. Dress the crystals as illustrated.

Crystal Sets

• A. 96 Sets. (1)14mm + AS9-2″
• B. 8 Sets. (1)Ring + (1)14mm+AS9-3″
• C. 8 Sets. (1)Ring + (1)Square+ (8)14mm + AS9-3″
• D. 16 Sets. (22) 14mm
• E. 1 Piece. (1)14mm + AS8-50mm Ball
• F. 14 Sets. (3)14mm + AS9-2.5″
• G. 8 Sets. (31) 14mm
• H. 8 Sets. (19) 14mm
• I. 8 Sets. (1)Square + (1)14mm + AS9-2.5″
• J. 8 Sets. (1)14mm + AS9-1.5″

DETAILED ILLUSTRATION

WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and/or birth defects or reproductive harm. For more information go to www.p65warnings.ca.gov.

Part Number

• A.(1)-Mounting hardware
  • Wire connector ×2.
  • Mounting bar x1.
  • Lock washer ×1.
  • Hex nut ×1.
  • Nipple ×1.
  • Screw ×2.
• B. (1)-Canopy (W5″xH1″)-XSN1130CHCAN5IN
• C. (1)-Collar Ring
• D. (1)-Collar Loop-XSN1130CHLOOP
• E. (1)-Chain (4mmx72″)-XSN1130CHCHA4MM
• F. (1)-Center Column Kit Loop
• G. (1)-Center Column Kit
  • Top Glass Bowl; Ø6″, 16pin,14mm center hole.
  • XSN1139CHDIBOB16IN
  • Glass Vase; H8″
  • Center Bobeche; Ø4″, no pin,24mm center hole.
  • XSN1137BOB4IN
  • Glass Vase; H6″
  • Metal Cover ; H1.5″
• H. (16)-PVC candle sleeve
• I. (17)-Bobeche ; Ø4″, 6pin,24mm center hole.
  • XSN7464CHBOB6PN
• J. (8)-10″ Upper Arms with Male Plug
  • XSN500CHARM10INKD
• K. (1)-Bottom Column Kit
  • Coupling.
  • Upper Metal plate with Female Plug.
  • Center Glass Bowl; Ø6″, 8pin,14mm center hole.
  • XSN1139CHDIBOB6IN
  • Glass Vase; H6″
  • Metal Cover ; H1.5″
  • Lower Metal plate with Female Plug.
  • Metal Bowl ; Ø5.5″
• L. (8)-15″ Lower Arms with Male Plug
  • XSN500CHARM15INKD
• M. (2)-Check Ring
• N. (1)-Bottom Glass bowl; Ø6″, 8pin,14mm center hole.
  • XSN1139CHDIBOB6IN
• O. (1)-Finial-XSN1130CHFIN

Crystorama.com.

References

• Crystorama Lighting
• p65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>