Simplex 4009-9809 IDNet Repeater Option Card Instruction Manual
- June 4, 2024
- Simplex
Table of Contents
Simplex 4009-9809 IDNet Repeater Option Card
introduction
Cautions and Warnings
- DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED. Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify Simplex.
- ELECTRICAL HAZARD – Disconnect electrical power when making any internal adjustments or repairs. Servicing should be performed by qualified Simplex Representatives.
- STATIC HAZARD – Static electricity can damage components. Therefore, handle as follows:
- Ground yourself before opening or installing components (use the 553-484 Static Control Kit).
- Keep uninstalled component wrapped in anti-static material at all times.
RADIOFREQUENCY ENERGY
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area may cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
Overview
This publication shows how to install the 4009-9809 IDNet Repeater Option Card
(Part No. 565-773) into a 4009 IDNet NAC Extender (4009 IDNet) or 4009
TrueAlert Addressable Controller (4009 TrueAlert). The repeater card
regenerates and provides a power and distance boost for the IDNet channel, and
retransmits it on its output side at host panel IDNet levels.
Refer to the 4009 IDNet NAC Extender Installation Instructions (574-181) or
TrueAlert Addressable Controller Installation Instructions (574-762) for
configuration information. Refer to the 4009 IDNet Field Wiring Diagrams
(Part No. 842-068) or 4009 TrueAlert Addressable Controller Field Wiring
Diagrams (Part No. 842-158) for additional wiring information.
In this Publication
This publication discusses the following topics:
IDNet Repeater Option Card
Figure 1 illustrates the IDNet Repeater Option Card interface and the terminal block that supports the IDNet interface.
Wiring
Repeater Card Wiring
Use the information in Figure 2 to terminate all Class A (Style 6) wiring. For
Class B (Style 4) wiring, connect a jumper wire(s) from TB1-1 to TB1-3 and
from TB1-2 to TB1-4. Refer to the 4009 IDNet Field Wiring Diagrams (Part No.
842-068) or 4009 TrueAlert Addressable Controller Field Wiring Diagrams
(Part No. 842-158) for complete wiring, compatible appliances, current, and
line distance information.
Figure 2. IDNet Repeater Option Card Wiring
Notes:
- Refer to the 4009 IDNet Field Wiring Diagrams (Part No. 842-068) or TrueAlert Addressable Controller Field Wiring Diagrams (Part No. 842-158) for Class B and Class A connections.
- The maximum number of devices on a repeated portion of the IDNet channel is 100. Total devices on host IDNet channel and repeated IDNet channel(s) combined not to exceed 250.
Module Installation
Mounting the Repeater Card
Install the 4009-9809 Repeater Option Card onto the 4009 IDNet or 4009 TrueAlert option card plate assembly (636-871) using the following steps and Figure 3.
- Disconnect battery and then AC power from the 4009 IDNet or 4009 TrueAlert.
- Secure the option card plate assembly (636-871) to the 4009 IDNet or 4009 TrueAlert using four slotted torx screws (supplied).
- Insert the 14-pin header (Part No. 166-490) into 4009 IDNet System Board connector P6 or 4009 TrueAlert Main Board connector P4.
- Line up the back 14-pin connector P1 of the IDNet Repeater Option Card with the 14- pin header installed on the 4009 IDNet System or 4009 TrueAlert Main Board and insert pins into connector.
- Secure the IDNet Repeater Option Card to the plate assembly using four slotted torx screws (supplied).
- For the 4009 IDNet, set the hardware configuration switches SW1/position 5 located on the 4009 IDNet System Board to “ON” to configure the IDNet Repeater Option Card to the 4009 IDNet and SW1/position 8 to “OFF” for IDNet control. Refer to the 4009 IDNet NAC Extender Installation Instructions (574-181) for detailed information on setting the hardware configuration switch SW1.
For the 4009 TrueAlert, set the hardware configuration switches SW4/position 3 and 4 on the 4009 TrueAlert Main Board to “ON” and “OFF” respectively for IDNet control and SW4/position 5 to “ON” to configure the IDNet Repeater Option Card to the 4009 TrueAlert. Refer to the 4009 TrueAlert Addressable Controller Installation Instructions (574-762) for detailed information on setting the hardware configuration switch SW4.
You can now reconnect AC and Battery Power.
Documents / Resources
|
Simplex 4009-9809 IDNet Repeater Option
Card
[pdf] Instruction Manual
4009-9809, IDNet Repeater Option Card, Repeater Option Card, Option Card,
4009-9809, Card
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>