oursson JM4600, JM4700 Auger Juicer Instruction Manual

oursson JM4600, JM4700 Auger Juicer

Product Information

The JM4600/JM4700 is an electric juicer that operates on 220-240 V~. The device comes with a safety lock and is equipped with a spout with a lid for juice, an ON/OFF/Reverse button, and a spout for pulp. The device has a filter, a feeding bowl, an auger/pressure screw, and a pulp container and juice container.

SAFETY INSTRUCTIONS, Pic. A

When using electrical appliances should take the following precautions:

• Use the device according to the following instructions manual.
• Install the device on a stable surface.
• Use only the tools, which are included in the product set.
• To protect against risk of electrical shock do not put the cord in water or other liquid. If for some reason the water got into the unit, contact an authorized service center (ASC) OURSSON AG.
• For power supply, use a power grid with proper characteristics.
• Do not use the device in areas where the air can contain vapors of flammable substances.
• Never attempt to open the device by yourself ­ it could possibly be the reason of an electrical shock can lead to product malfunction and will invalidate the manufacturer’s warranty. For repair and maintenance, contact only authorized service centers meant for repair of products under the trademark OURSSON.
• When moved from a cool to a warm place and vice versa unpack it before use and wait 1-2 hours without turning it on.
• In order to prevent electrical shock do not immerse the entire product or the wires into the water.
• Be particularly careful and cautious when using the device near children.
• Do not touch any hot parts, as this may cause injury. · The power cord is specially made relatively short in order to avoid the risk of injury.
• Do not allow the cord to hang over the sharp edge of the table or touch hot surfaces.
• Do not connect this device to a grid which is over-loaded with other appliances: it can lead to the fact that the device will not function properly.
• Do not install the device near gas and electric stoves and ovens.
• After use, make sure to disconnect the device from the power grid.
• Keep the device from bumps, falls, vibration and other mechanical influences.
• Make sure to disconnect the device from the power grid before cleaning or changing accessories.
• Do not use the device outdoors.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
• They can only use the device under the supervision of the person responsible for their safety, or after instruction on the safe use of the device. Do not allow children to play with the product.
• This product is intended only for use in the home.
• If the power cord is damaged, it must be replaced by a specialist from the authorized service center ( ASC ) OURSSON AG to avoid danger.
• Use only the tools, which are included in the product set.
• When cleaning the appliance do not use abrasives and organic cleaners (alcohol, gasoline, etc.). When cleaning the device it is allowed to use a small amount of neutral detergent.

RECOMMENDATIONS

• Please read the instruction manual before using the device. Keep the manual after reading for further use.
• All illustrations in this manual are schematic representations of real objects, which may differ from the actual images.
• If the filter has been damaged, stop using the device and contact an authorized OURSSON AG service center.

Warning

• The device is equipped with a safety lock. If the lid isn’t installed correctly on the cup, a special latch on the lid won’t get into the groove of the cup, it wouldn’t be possible to turn the lid clockwise. Make sure the lid is installed correctly.
• Do not apply physical force to the device, as this may damage the device due to the user’s fault.

PRODUCT SET, Pic. B

1. Pusher: 1 pc.
2. Juicing bowl with spouts: 1 pc.
3. Auger/Pressure screw: 1 pc.
4. Filter:1 pc.
5. Silicone filter ring: 1 pc.
6. Pulp container: 1 pc.
7. Juice container:. 1 pc.
8. Feeding bowl: 1 pc.
9. Motor unit: 1 pc.
10. Cleaning brush: 1 pc.
11. Feeding bowl lid (for JM4700): 1 pc.
12. Instruction Manual: 1 pc.
13. Warranty card: 1 pc.

ELEMENTS OF DESIGN, Pic. C

1. Spout with lid for juice
2. ON/OFF/Reverse button
3. Spout for pulp

UTILIZATION, Pic. D

Before first use, wipe the device with a soft, dry cloth. The rest of the parts wash with warm water and detergent. Before assembling or disassembling the device and / or removing attachments, make sure that the device is unplugged.

• Step 1, Pic. D-1 Take the filter and place the silicone ring on it, aligning the tab on the ring with the slot in the filter. Press lightly on the silicone ring. Make sure the silicone ring is firmly seated on the filter.
• Step 2, Pic. C-3 Place the bowl with spouts on the motor unit. For model JM4600, align the two marks as shown in the illustration. For model JM4700, align the juice and pulp spouts with the grooves on the motor block.
• Step 3, Pic. C-4 Insert the auger/pressure screw into the center of the spout bowl by gently pushing and turning until it snaps into place.
• Step 4, Pic. C-5 Insert the filter into the bowl with the spouts, with the silicone ring facing down. Note the position of the largest ridge on the filter. Make sure the dots on the filter and bowl are aligned as shown in the illustration.
• Step 5, Pic. C-6 Place the feeding bowl on the bowl with spouts and turn it clockwise as shown in the fpicture. Place the lid on the feeding bowl (for model JM4700).

Note: Always leave the spout lid open when juicing ingredients that produce a lot of foam, Pic. C-1.
The power button is located on the handle of the device.
The key has three positions (Pic. C-2):

1. ON (Δ) ­ turn on;
2.  ­ Pause /stop motor;
3. REV (∇) ­ Reverse.

Warning: When switching between the «On» and «Reverse» positions, be sure to move the button to the «Stop» position for 5 seconds to stop the auger.
Place the pulp container and juice container under the respective spouts. After completing the assembly, plug in the device.

ORDER OF OPERATION, Pic. E

1. Assemble the device, Pic. D. Plug in the device.

2. Press the power button, Pic. C-2.

3. Using the pusher, place the prepared ingredients into the filling hole, Pic. E. The products should be cut into pieces for the JM4600 model. For the JM4700, you can use whole or cut ingredients. To place whole ingredients, remove the lid from the feeding bowl, Pic. B- 11.
   Note
   

   • Follow the cooking guidelines to prepare the ingredients.

   • Do not overfill the feeding bowl.
     Warning
     

   • To avoid overheating of the motor, do not use this device for more than 10 minutes without a pause. The break between cycles should be 5 minutes.

   • Do not place ingredients that are hotter than 80°C into the feeding bowl. Let them cool down.

   • Do not use a spoon or other foreign objects in order to remove the pulp from the pulp spout as it may damage the device.

   • To push the ingredients into the feeding chute, use only the pusher, which is included with the device. It is strictly forbidden to push ingredients with hands, as this could cause injury.

4. If a dense mass of ingredients gets stuck in the juicer mechanism and impedes the movement of the juice, move the button to the “Stop” position until the engine comes to a complete stop, then move the button to the “Reverse” position. The auger will start to rotate in the opposite direction.After a few seconds, again move the button to the “Stop” position and after stopping the engine, press “ON”. Repeat this operation if necessary.

5. At the end of juicing, close the lid at the spout so that the remaining juice does not drip onto the table. Switch off the device and unplug it.

Note: Freshly squeezed juices are recommended to be consumed immediately after preparation, as after a while they begin to exfoliate and lose their beneficial properties.

PREPARATION RECOMMENDATIONS

1. Do not place into the device dried or hard ingredients, such as whole grains, fruits with hard seeds, thickskinned or ice. This can damage juice maker’s parts.
2. Beans or grain can be used if they were presoaked overnight and boiled.
3. Do not press the products without juice content (coconut, sugar cane, whole grains, etc.).
4. Do not use ingredients that contain an excessive amount of vegetable oil or animal fat. Do not use the juice maker for squeezing oil from the ingredients. If the plant oil or animal fat falls onto the pressure screw, it can reduce performance and damage juice maker’s parts.
5. Do not load pulp into the juice maker. This can lead to a shutdown or lock the juice cup’s lid.
6. After juicing the ingredients with small seeds, you must clean all parts of the device from the seeds.
7. The amount of juice depends on the freshness and juiciness of the products. The fresher the vegetables or fruit, the more juice you can make.

Hard seeds

| Apricots, peaches, mangoes, nectar- ines, plums, etc.|

Products with seeds or hard seeds should be freed from seeds.

With hard or inedible peel

| Mangoes, oranges, pineapples, water- melons, melons, etc.|

Clean the peel and remove seeds.

Soft fruits and vegetables

|

Oranges, tomatoes, etc.

|

Wash and if necessary peel the fruits and vegetables and remove large seeds, remove the stalk. Cut into pieces.

Solid fruits and vegetables

|

Carrots, potatoes, beets, etc.

| Solid fruits/vegetables can put additional stress on the engine and cause it to overheat and stop. Observe breaks between the cycles. Cut hard ingredients into small cubes or wedges. You can pre-soak food in cold water if it is not fresh.

Ingredients with small seeds

|

Raspberries, ap- ples, pears, grapes, etc.

|

Products with small seeds must be loaded into the juicer slowly in small portions to prevent clogging of the filter. Before juicing, remove the twigs from the grapes, and the peel from the pomegranate.

Fibrous ingredients

|

Celery, cabbage, pineapple

| Cut into strips. If necessary, separate the stems from the leaves. Load leafy ingredients in small portions. When juicing, alternate leaves and stem pieces. For best results, we recommend to periodically disassemble and wash the juicer. If the leaves are tangled on the pressure screw, open the lid and remove the fiber, and then continue. When juicing products such as pineapples, you must first peel and cut out the core, then cut it into small pieces.

CLEANING AND MAINTENANCE, Pic. F

• Clean all parts of the device immediately after use.
  Warning: For an easier cleaning of the device, pour water into the feeding chute and turn on the juice maker for 30 seconds.

• Turn off the device before unplugging it.

• Remove the pusher, remove the feeding bowl with spouts by turning it counterclockwise. Remove any remaining pulp from the bowl. Remove it from the motor block. Remove the auger and filter carefully. Detach the silicone ring from the filter.

• Wash all the elements of device, except of motor unit, in warm soapy water, using a brush.
  Warning: It is strictly forbidden to clean parts of the device in dishwasher or dry them in dryer, as this may damage the device.

• Wipe the motor unit with a soft damp cloth.

• Danger: Never immerse the motor unit in water because of the risk of electric shock.

• After cleaning, thoroughly dry all the elements of the device and store them in a dry, clean place.

POSSIBLE PROBLEMS AND SOLUTIONS

Device does not work on

| •  Check whether the power cord is connected to the outlet. If the device is not connected, plug it to the outlet.

•  Check whether the device is assembled correctly. If not, disassemble and reassemble accord- ing to the instructions.

•  If the problem persists, contact an authorized service center OURSSON.

Little juice

| •  The various ingredients have different moisture contents.

•  If the products are not fresh, they lost their juiciness. Put the ingredients in water for 1-2 hours to recover.

•  Make sure that the silicone gasket is installed correctly and firmly.

•  If you are using ingredients with small seeds, then after few loads their presence can reduce the amount of juice. For best results, between preparations disassemble the machine and clean it from seeds.

A lot of pulp in the juice

| •  With continued juicing and depending on the ingredients, juice may contain much pulp.

•  To reduce the pulp in the juice, disassemble the juice cup and remove the pulp more often.

•  If the filter or screw is damaged – it can affect the performance and quality of juice. It is recom- mended to replace them. The service life of each part depends upon the duration and the method of using the device, and pressing ingredients.

•  If too much of the ingredients are loaded into the juice maker simultaneously, this can lead to frequent stoppages and to a large number of pulp in the juice. Place ingredients slowly and in small portions.

Extraneous sounds when the device is working

| •  Make sure that all parts are correctly assembled.

•  Do not turn the juice maker without ingredients or at least liquid in it. Empty working juice maker may damage the pressure screw

•  Depending on the type or size of various ingredients different noises my occur.

•  Noise may occur when the juice maker is working on uneven or inclined surfaces. Lace it on a

flat stable surface.

Pulp is very wet| •  At the beginning of juicing, the pulp can be wet.

•  The recovered pulp can be wet if you are using stale ingredients

Cup vibration| •  A small vibration of juice cup is allowed during operation. It is not considered a malfunction

The device has stopped working

| •  Make sure the amount of fruit and vegetables is not too large and the motor is not overloaded.

•  Make sure all the large seeds were removed from the fruit.

•  Turn off the device and switch it on REV (Reverse) mode for 2-3 seconds. Turn on the device

again.

Specifications

Specifications

Model| JM4600| JM4700
Power consumption, W| max 150| max 150
Rated voltage| 220-240 V~; 50-60 Hz| 220-240 V~; 50-60 Hz
Protection class| I| I
Storage and transportation temperature requirements*| -25 °C to +35 °C| -25 °C to +35 °C
Operation temperature requirements| +5 °C to +35 °C| +5 °C to +35 °C
Humidity requirements| 15-75%| 15-75%
Dimensions (H×W×L), mm| 101x125x359| 150х110х372
Weight, kg| 1.6| 2.2

Products should be stored in dry, ventilated warehouses at temperatures below – 25°C.

PRODUCT CERTIFICATION

For information on product certification, see http://www.oursson.com or ask seller for a copy.

Warning: Only a qualified specialist of an authorized service center OURSSON AG can repair the juice maker.

SERVICING

Company OURSSON AG expresses great appreciation to you for choosing our products. We have done everything possible so that this meets your needs, and the quality corresponds to the best world standards. If your OURSSON branded product will need maintenance, please contact one of the authorized service center (hereinafter – ASC). A complete list of ASC and their exact addresses can be found on the website www. oursson.com.

Warranty obligations OURSSON AG

1. Warranty obligations OURSSON AG, provided ASC OURSSON AG, apply only to models designed OURSSON AG for the production or supply and sale within the country where the warranty service is provided, purchased in this country, certified for compliance with the standards of this country, and also marked the with official marks of conformity.
2. Warranty obligations OURSSON AG operate within the law on protection of consumer rights and are regulated by the laws of the country in which they are provided, and only when the product is used exclusively for personal, family or household purposes. Warranty obligations OURSSON AG shall not apply to uses of goods for business purposes or in connection with the acquisition of goods to meet the needs of enterprises, institutions and organizations.
3. OURSSON AG sets for its products the following terms of use and warranty periods:

Product name

| Terms of use, months| Warranty Period, months
---|---|---
Microwave ovens breadmakers, induction hobs Multicookers, kitchen processors, electric kettles, electric grills, hand blenders, hand mixers, meat grinders, blenders, toasters, airpots, toasters, juicers, steamers, coffee makers, choppers, freezers, refrigerators, automatic coffee machines Kitchen scales|

60

|

24

4. Warranty obligations OURSSON AG shall not apply to the following products, if their replacement is assumed and is not connected with disassembling products:
   • Batteries.
   • Cases, straps, cords for carrying, mounting accessories, tools, documentation that came with the product.
5. Warranty does not cover defects caused due to violations of the rules of consumer use, storage or transportation of the goods, actions of third parties or force majeure, including but not limited to the following cases:
   • If the defect was a result of careless handling, used for other purposes, violations of conditions and rules of operation set forth in the instruction manual, including as a result of exposure to high or low temperatures, high humidity or dust, traces of opening the device independently and/ or selfrepair, mismatch state standards for power grids, getting liquids, insects or other foreign objects, substances inside the device, as well as long-term use of the product in extreme operational modes.
   • If the defect of the product was a result of unauthorized attempts to test the product or make any changes in its construction or software programs, including repair or maintenance in unauthorized service centers.
   • If the defect of the product was a result of use of non-standard and/or low quality equipment, accessories, spare parts, batteries.
   • If the defect of the product is associated with its use in conjunction with additional equipment (accessories), other than additional equipment recommended by OURSSON AG for use with this product. OURSSON AG is not responsible for the quality of the additional equipment (accessories) manufactured by third parties, for the quality of its products together with such equipment, as well as the quality of the work of the additional equipment of OURSSON AG together with the products of other manufacturers.
6. Product defects detected during the lifetime of the product are eliminated by the authorized service centers (ASC). During the warranty period, elimination of defects is free of charge with the presentation of the original certificate of guarantee and documents that confirm the fact and date of the contract of retail purchase. In the absence of such documents, warranty period is calculated from the date of manufacture of goods. It should be taken into account:
   • Setup and Installation (assembly, the connection, etc.) of the product described in the documentation attached to it, does not enter the scope of warranty OURSSON AG and can be performed by the user as well as the specialists of most authorized service centers on a paid basis.
   • Work upon maintenance of products (cleaning and lubricating the moving parts, replacement of consumables and supplies, etc.) are made on a paid basis.
7. OURSSON AG is not responsible for any damage directly or indirectly caused by their products to people, pets, property, if it occurred as a result of non-observance of the rules and conditions of use, storage, transportation or installation of the product, intentional or negligent actions of consumer or third parties.
8. Under no circumstances, OURSSON AG is not responsible for any special, incidental, indirect or consequential loss or damage, including but not limited to: lost profits, damages caused by interruptions in the commercial, industrial or other activities, arising from the use of or inability to use the product.
9. Due to continuous product improvement, design elements and some technical specifications are subject to change without prior notice from the manufacturer.

Using the product when after the terms of use (lifetime):

1. Lifetime set by OURSSON AG for this product applies only when the product is used exclusively for personal, family or household needs, as well as the consumer observes the correct operation, storage and transportation of products. Under the condition of careful handling of the product and compliance with the rules of operation the actual life may exceed the lifetime set by OURSSON AG.
2. At the end of the product lifetime, you should contact an authorized service center for to conduct a preventive maintenance of the product and determine the suitability for further use. Work on conducting a preventive maintenance of the products is also made in service centers on paid basis.
3. OURSSON AG does not recommend the use of this product after the end of its lifetime without its preventive maintenance by the authorized service center, since in this case, the product can be dangerous to the life, health or property of the consumer.

Product Recycling and Disposal

This appliance has been identified in accordance with the European directive 2002/96/EG on Waste Electrical and Electronic Equipment ­ WEEE. After the expiration of the lifetime, the product cannot be disposed with another household waste. Instead, it shall be deposited in the appropriate recycling collection point for electrical and electronic equipment for proper treatment and disposal in accordance with federal or local law. By disposing correctly this product, you will help to conserve natural resources and preventing the product from damaging the environment and human health. For more information on the collection point and recycling of this product, please contact your local municipal authorities or the enterprise for household waste disposal.

Date of manufacture
Each product has a unique serial number in the form of alphanumeric row and is duplicated with a barcode that contains the following information: name of the product group, date of manufacture, serial number of the product.

Serial number is located on the rear of the product, on the package and the warranty card.

1. The first two letters-correspondence to the product group (juice maker – JM).
2. The first two digits ­ year of manufacture.
3. The second two digits ­ month of manufacture.
4. The last two digits ­ serial number of product.

Warning
To avoid misunderstandings, we highly recommend you to read carefully the instruction manual and the warranty obligations. Check the correctness of the warranty card. Warranty card is valid only if the following are correctly and clearly stated: model, serial number, date of purchase, clear stamps, buyer’s signature. The serial number and the model of the device must be the same as in the warranty card. If these conditions are not fulfilled or the data specified in the warranty card was changed, the warranty card is invalid.

If you have questions or problems with OURSSON AG products – please contact us by e-mail: support@oursson.com
This manual is under protection of international and EU copyright law. Any unauthorized use of the instructions, including copying, printing and distribution, but not limited to, involves the application of the guilty person to civil liability and criminal liability.

Contact information

1. Manufacturer of goods – OURSSON AG (Orson AG), Rue du Grand-Chêne 5, 1003 Lausanne, Switzerland.
2. Certification information product available on the website www.oursson.com.
   OURSSON AG Made in China

References

• Oursson Forum • Главная страница
• OURSSON / Oursson
• OURSSON - интернет-магазин кулинарных инноваций и товаров для приготовления здоровой еды
• OURSSON / Oursson
• OURSSON / Oursson
• OURSSON - интернет-магазин кулинарных инноваций и товаров для приготовления здоровой еды

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>