oursson MO7053 Capacious Full Oven Instruction Manual

MO7053 Capacious Full Oven

Instruction Manual

MO7053 Capacious Full Oven

SAFETY INSTRUCTIONS, Рiс. А

Danger symbol
A reminder to user about high voltage.
Warning symbol
A reminder to user about the necessity of operating exactly according to the instructions.

When using electrical appliances should take the following precautions:

• Use the device according to the following instructions manual.
• Install the device on a stable surface.
• Use only the tools, which are included in the product set.
• To protect against risk of electrical shock do not put the cord in water or other liquid. If for some reason the water got into the unit, contact an authorized service center (ASC) OURSSON AG.
• For power supply, use a power grid with proper characteristics.
• Do not use the device in areas where the air can contain vapors of flammable substances.
• Never attempt to open the device by yourself – it could possibly be the reason of an electrical shock can lead to product malfunction and will invalidate the manufacturer’s warranty. For repair and maintenance, contact only authorized service centers meant for repair of products under the trademark OURSSON. • When moved from a cool to a warm place and vice versa unpack it before use and wait 1-2 hours without turning it on.
• In order to prevent electrical shock do not im-merse the entire product or the wires into the water.
• Be particularly careful and cautious when using the device near children.
• Do not touch any hot parts, as this may cause injury.
• The power cord is specially made relatively short in order to avoid the risk of injury.
• Do not allow the cord to hang over the sharp edge of the table or touch hot surfaces.
• Do not connect this device to a grid which is overloaded with other appliances: it can lead to the fact that the device will not function properly. • Do not install the device near gas and electric stoves and ovens.
• After use, make sure to disconnect the device from the power grid.
• Keep the device from bumps, falls, vibration and other mechanical influences.
• Make sure to disconnect the device from the power grid before cleaning or changing accessories.

Risk of burn symbol
Reminder for user of high temperatures.

• Do not use the device outdoors.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. They can only use the device under the supervision of the person responsible for their safety, or after instruction on the safe use of the device. Do not allow children to play with the product.
• This product is intended only for use in the home.
• If the power cord is damaged, it must be replaced by a specialist from the authorized service center (ASC) OURSSON AG to avoid danger.
• Use only the tools, which are included in the product set.
• When cleaning the appliance do not use abrasives and organic cleaners (alcohol, gasoline, etc.). When cleaning the device it is allowed to use a small amount of neutral detergent.

RECOMMENDATIONS

• Please read the instruction manual before using the device. Keep the manual after reading for further use.
• All illustrations in this manual are schematic representations of real objects, which may differ from the actual images.
• Do not shift the device when utilizing it.
• Use the device only for cooking and heating food.
• Do not use the device as a heat source.
• Do not try to use the device with an open door.
• Use only heat resistant kitchenware, suitable for mini-ovens.
• Do not place into device cans, bottles, tight closed containers and too big objects. This may lead to a personal injury or breakage of the device.
• Do not place raw meat / fish directly onto the grid, because fat and oil can ignite. Use a baking mold, wrapping products beforehand. Make sure that foil isn’t contacting with the heating elements.
• When using foil, place the pan on a medium or low level.
• Do not leave the working device unattended.
• Do not put in/on the device paper, cardboard, plastic, towels, etc., as this can cause a fire.
• Do not touch the body or the door when the device is working or immediately after its use. The surface of the device heats up which may lead to burns.
• Use potholders or oven gloves to take the product out of the oven.
• While using the device do not slam the door, do not put trays or other objects on the door, avoid contact of cold water with the heated open door. Pic. A-1.
• If while preparing, food caught on fire or began to emit smoke, turn off the device and unplug it. Do not open the door until fire is stopped, because the oxygen supply will intensify the flame. Do not pour water over the device, the glass may crack.

SETTING, Рiс. A-2

• Place the device on a flat horizontal heat resistant surface, high from children’s reach, keeping the distance from walls/furniture as shown in the picture A-2. One side must be completely free. It is forbidden to embed this device.
• Do not place the working device under/near curtains or other flammable materials, as this may cause a fire.

PRODUCT SET, Рiс. В

Body. ……………………………………………………………… 1 pc.
1 Enameled pan …………………………………………….. 1 pc.
2 Grid …………………………………………………………… 1 pc.
3 Handle for pan and grid ……………………………….. 1 pc.
4 Handle for spit. ……………………………………………. 1 pc.
5 Spit ……………………………………………………………. 1 pc.
6 Tray for crumbs …………………………………………… 1 pc.
Instructions manual …………………………………………. 1 pc.
Warranty card …………………………………………………. 1 pc.

ELEMENTS OF DESIGN, Рiс. С-1

1. Door handle
2. Spit bracing
3. Slots for grid and pans
4. Door
5. Control panel
6. Ventilation openings
7. Operation indicator
8. Removable tray for crumbs
   Inner backlight, Pic. C-1-2
   Upper and lower heating elements, Pic. C-1-1

UTILIZATION

Control panel, Рiс. С-2
Function switch, Рiс. С-2-4

• STOP position, turns off the convection / spit operation

• Convection (hot air circulation around the product)

• Spit (spit rotates, uniformly browning on all sides)

• Convection and spit
  Temperature regulator, Рiс.С-2-1

• Adjusting the temperature from 100°C to 230°C
  P Preparation mode switch, Рiс.С-2-2

• STOP position

• Upper heating element (upper heating)

• Lower heating element (lower heating)

• Upper and lower heating elements, simultaneous operation of both upper and lower heating elements
  Timer, Рiс.С-2-3

• Timer, time selection from 0 up to 60 minutes.

• STOP position, utilized for stopping the cooking process.

Spit construction, Рiс. С-5

1. Hook
2. Clamp
3. Fastener
4. Bayonet
5. Motor coupling

Preparation for operation
Before first use, wipe the body with a soft, dry cloth.
Wash the other parts with warm water and detergent.
Before assembling or disassembling the make sure that  the device is unplugged. Thoroughly dry all parts.
Turn on the empty device for 15 minutes, set the maximum temperature of 230 °C in , to remove the smell of a new device. Ventilate the room. Allow the device to cool.

Order of operation, Рiс.C-2

1. Make sure that the crumb tray is completely installed, and timer knob is set in the . position. Plug in the device.

2. Set the required temperature with the regulator.

3. Turn on the timer for 5 minutes in the , for the device to heat up. Timer knob will turn automatically in the cooking process.

4. Choose a required mode with the help of correspond-ed regulators: .

5. Place prepared beforehand products on the pan/grid/ spit. Do not place products closer than 2 cm. from the heating elements.

6. Carefully install grid, pan or spit into the device, Pic. C-3. Close the door.

7. Turn on the timer , setting the required time. It isn’t recommended to open the door in the preparation process.
   NOTE: When the device is working, the inner backlight and operation indicator , Рiс. С-1.

8. When the preparation process is completed, the timer (device) turns off automatically, you will hear a sound signal. Set all the regulators into the position.

9. Carefully open the door and take out prepared product with the help of potholders or a special handle for pan, Pic. C-4.

Using the Spit, Рiс. С-5

1. Take the spit and remove one clamp from it .

2. Impale beforehand prepared meat or poultry onto the center of the spit and tighten the clamp on both sides.
   All the parts of the meat or poultry must be clamped, nothing should hang or dangle.

3. Turn on the timer for 10 minutes in the , mode for the device to heat up.

4. Install the spit into the slots, sharp end into the right socket, left end onto a special square support .

5. On the lower level, place a pan, so that the juice from the meat/poultry dripped into it.

6. Set the required temperature with the regulator.

7. Choose a required mode with the help of corresponded regulators: , and, .

8. Turn on the timer , set the required time.

9. When the preparation process is completed, the timer (device) turns off automatically, you will hear a sound signal. Set all the regulators into the position.

10. Take out the spit with a special handle 4 , Pic. B, placing its hooks on both sides of the spit. First, carefully raise the spit from the left slot and pull, then remove the spit from the right socket. Take off the meat or poultry from the spit and put it on a cutting board or platter.

RECOMMENDATION ON PREPARATION

Product name| Preparation mode| Position of the grid/pan| Temperature| Cooking time| Note
---|---|---|---|---|---
Meat| Pork| | | 200оС| 35-40 min.| Marinate before cooking, cut into small pieces (3x3x3 cm).
Beef / Lamb| | | 200оС| 40-45 min.| Marinate before cooking, cut into  small pieces (3x3x3 cm).
Meat semi- finished products| Sausages| | | 160оС| 15-20 min.| Make a small cut line.
Install crumbs tray 6 .
Hotdogs| | | 160оС| 15-20 min.| Remove the sausage skin. Install crumbs tray 6 .
Meatballs| | | 120оС| 20-25 min| Pour 150 ml of water into the pan.
Beefsteak| | | 160оС| 15-20 min| Make small cut lines (mesh), rub with salt, spices and herbs.
Poultry| Fillet| (at the end of pre-parathion for a crispy crust)| | 160оС| 25-30 min| To preserve juiciness use a baking sleeve. Rub with salt, spices and herbs.
Product name| Preparation mode| Position of the grid/pan| Temperature| Cooking time| Note
---|---|---|---|---|---
Poultry| Drumstick| | | 160оС| 25-30 min| To preserve juiciness use a baking sleeve. Rub with salt, spices and herbs.
Wings| | | 180оС| 15-20 min| Rub with salt, spices and herbs.
Whole leg| | | 160оС| 25-30 min| Rub with salt, spices and herbs. Pour 150 ml of water into the pan.
Whole chicken| (at the end of preparation for a crispy crust)| | 160оС| 30-40 min| Pour 150 ml of water into the pan

Rub with salt, spices and herbs.

Fish| Whole| | | 130оС| 15-20 min| Install crumbs tray 6 . To soften small fish bones lay slices of lemon.
Portion pieces| | | 150оС| 15-20 min| Pour 150 ml of water into the pan.
Toasts| | | 180оС| 7-10 min| Cut bread for toast. Install crumbs tray 7 . Before preparation brush the toasts with butter.
French toast| | | 120оС| 15-20 min| Cut the bread into cubes (1x1x1 cm). Before cooking sprinkle with vegetable oil, salt, pepper and herbs.
Fried potatoes| | | 150оС| 25-30 min| Cut the potatoes into strips (0.5×0.5×4 cm). Season with salt and add onion at the end of cooking.
Vege- tables| Stewed|

|

| 100оС| 30-35 min| Cut the vegetables. Use a heat-resistant container.
Grill| | | 120оС| 10-15 min| Add salt at the end of cooking..
Baking| Pie| | | 120оС| 30-35 min| Use a round baking mold with high ends.
Cookies| | | 160оС| 15-20 min| Use a baking sheet.
Cupcake| | | 100оС| 30-35 min| Use a cupcake mold.
Product name| Preparation mode| Position of the grid/pan| Temperature| Cooking time| Note
---|---|---|---|---|---
Pizza (fresh/ semi finished)| 8 inch /20 cm| | | 180оС| 8-10 min| Coat the edges of pizza with tomato sauce, mayonnaise or other sauce of your choice to prevent drying out.
Lasagna| | | 100оС| 25-30 min| Pour 150 ml of water into the pan
Casseroles – Vegetable, curd, meat, potatoes. (500g)| | | 100оС| 30-35 min| Use a heat-resistant container. Rup the top with a mix of cream and eggs.
Meat/poultry on the spit (900g)| | | 150оС| 40 min| Rub the surface of the product with a vegetable oil.
Sausages on the spit (250g)| ****| | 150оС| 15-20 min| Rub the surface of the product with a vegetable oil.

NOTE: Cooking time and temperature in the table are advisory in nature and can vary depending on the recipe.

DISPOSAL

• Before disposing of the old device, for safety, cut the cord to prevent further use.

CLEANING AND MAINTENANCE, Рiс. D

• Unplug the device.
• Let the device to cool, before cleaning it.
• Open the door completely and remove the crumb tray. For this, grab the edge of the tray, lift it slightly and gently pull it toward you.
• Wash the grid, pan, spit in a warm soppy water. They can be washed in a dishwasher. The temperature in the dishwasher must not exceed 60 oC.
• Wipe the body of the device, crumbs tray, and inner surface (besides heating elements) with a damp soft cloth.
• Never immerse the motor unit into the water because of the danger of electric shock.
• Thoroughly dry all parts.

POSSIBLE PROBLEMS AND SOLUTIONS

and wait for the voltage to normalize.
There is steam| When cooking food with a high amount of liquid, certain amount of steam can appear.| Be careful when opening the door, not to get burn from steam.
Burning smell| 1. There are crumbs on the tray.
2.Fat accumulated on the grid, pan or on the inside of the device.| 1.  Clean the crumbs tray after every use of the device.
2.  Wipe the device inside (cooled) and wash the grid and pan immediately after use.

PRODUCT CERTIFICATION

For information on product certification, see http://www.oursson.com or ask seller for a copy.

Specifications

condensate
Class of protection| I
Dimensions, mm (HxWxD)| 660х450х415
Weight, kg| 9,85

Products must be stored in dry, ventilated warehouses at a temperature not lower than -25° C.
Only a qualified specialist of an authorized service center OURSSON AG can repair the device

SERVICING
Company OURSSON AG expresses great appreciation to you for choosing our products. We have done everything possible so that this meets your needs, and the quality corresponds to the best world standards. If your OURSSON branded product will need maintenance, please contact one of the authorized service center (hereinafter – ASC). A complete list of ASC and their exact addresses can be found on the website www.oursson.com.

Warranty obligations OURSSON AG:

1. Warranty obligations OURSSON AG, provided ASC OURSSON AG, apply only to models designed OURSSON AG for the production or supply and sale within the country where the warranty service is provided, purchased in this country, certified for compliance with the standards of this country, and also marked the with official marks of conformity.

2. Warranty obligations OURSSON AG operate within the law on protection of consumer rights and are regulated by the laws of the country in which they are provided, and only when the product is used exclusively for personal, family or household purposes. Warranty obligations OURSSON AG shall not apply to uses of goods for business purposes or in connection with the acquisition of goods to meet the needs of enterprises, institutions and organizations.

3. OURSSON AG sets for its products the following terms of use and warranty periods:
   Product name| Terms of use, months| Warranty Period, months
   ---|---|---
   Microwave ovens beadmakers, induction hobs Multicookers, kitchen processors, electric kettles, electric grills, hand blenders, hand mixers, meat grinders, blenders, toasters, airports, toasters, juicers, steamers, coffee makers, choppers, freezers, refrigerators, automatic coffee machines, milk frothier Kitchen scales| 60| 24

4. Warranty obligations OURSSON AG shall not apply to the following products, if their replacement is assumed and is not connected with disassembling products:
   • Batteries.
   • Cases, straps, cords for carrying, mounting accessories, tools, documentation that came with the product.

5. Warranty does not cover defects caused due to violations of the rules of consumer use, storage or transportation of the goods, actions of third parties or force majeure,  including but not limited to the following cases:
   If the defect was a result of careless handling, used for other purposes, violations of conditions and rules of operation set forth in the instruction manual, including as a  result of exposure to high or low temperatures, high humidity or dust, traces of opening the device independently and/ or self- repair, mismatch state standards for power grids, getting liquids, insects or other foreign objects, substances inside the device, as well as long-term use of the product in extreme operational modes.
   • If the defect of the product was a result of unauthorized attempts to test the product or make any changes in its construction or software programs, including repair or maintenance in unauthorized service centers.
   • If the defect of the product was a result of use of non-standard and/or low quality equipment, accessories, spare parts, batteries.
   • If the defect of the product is associated with its use in conjunction with additional equipment (accessories), other than additional equipment recommended by OURSSON AG for use with this product. OURSSON AG is not responsible for the quality of the additional equipment (accessories) manufactured by third parties, for the quality of its products together with such equipment, as well as the quality of the work of the additional equipment of OURSSON AG together with the products of other manufacturers.

6. Product defects detected during the lifetime of the product are eliminated by the authorized service centers (ASC). During the warranty period, elimination of defects is free of charge with the presentation of the original certificate of guarantee and documents that confirm the fact and date of the contract of retail purchase. In the absence of such documents, warranty period is calculated from the date of manufacture of goods. It should be taken into account:
   • Setup and Installation (assembly, the connection, etc.) of the product described in the documentation attached to it, does not enter the scope of warranty OURSSON AG and can be performed by the user as well as the specialists of most authorized service centers on a paid basis.
   • Work upon maintenance of products (cleaning and lubricating the moving parts, replacement of consumables and supplies, etc.) are made on a paid basis.

7. OURSSON AG is not responsible for any damage directly or indirectly caused by their products to people, pets, property, if it occurred as a result onion-observance of the rules and conditions of use, storage, transportation or installation of the product, intentional or negligent actions of consumer or third parties.

8. Under no circumstances, OURSSON AG is not responsible for any special, incidental, indirect or consequential loss or damage, including but not limited to: lost profits, damages caused by interruptions in the commercial, industrial or other activities, arising from the use of or inability to use the product.

9. Due to continuous product improvement, design elements and some technical specifications are subject to change without prior notice from the manufacturer.

Using the product when after the terms of use (lifetime):

1. Lifetime set by OURSSON AG for this product applies only when the product is used exclusively for personal, family or household needs, as well as the consumer observes the correct operation, storage and transportation of products. Under the condition of careful handling of the product and compliance with the rules of operation the actual life may exceed the lifetime set by OURSSON AG.
2. At the end of the product lifetime, you should contact an authorized service center for to conduct a preventive maintenance of the product and determine the suitability for further use. Work on conducting a preventive maintenance of the products is also made in service centers on paid basis.
3. OURSSON AG does not recommend the use of this product after the end of its lifetime without its preventive maintenance by the authorized service center, since inthe case, the product can be dangerous to the life, health or property of the consumer.

Product Recycling and Disposal
This appliance has been identified in accordance with the European directive 2002/96/EG on Waste Electrical and Electronic Equipment – WEEE. After the expiration of the lifetime, the product cannot be disposed with another household waste. Instead, it shall be deposited in the appropriate recycling collection point for electrical and electronic equipment for proper treatment and disposal in accordance with federal or local law. By disposing correctly this product, you will help to conserve natural resources and preventing the product from damaging the environment and human health. For more information on the collection point and recycling of this product, please contact your local municipal authorities or the enterprise for household waste disposal.

Date of manufacture
Each product has a unique serial number in the form of alphanumeric row and is duplicated with a barcode that contains the following information: name of the product group, date of manufacture, serial number of the product.
Serial number is located on the rear of the product, on the package and the warranty card.

1. The first two letters-correspondence to the product group (oven – MO).
2. The first two digits – year of manufacture.
3. The second two digits – month of manufacture.
4. The last two digits – serial number of product.

To avoid misunderstandings, we highly recommend you to read carefully the instruction manual and the warranty obligations. Check the correctness of the warranty card. Warranty card is valid only if the following are correctly and clearly stated: model, serial number, date of purchase, clear stamps, buyer’s signature. The serial number and the model of the device must be the same as in the warranty card. If these conditions are not fulfilled or the data specified in the warranty card was changed, the warranty card is invalid.
If you have questions or problems with OURSSON AG products – please contact us by e-mail: support@oursson.com
This manual is under protection of international and EU copyright law. Any unauthorized use of the instructions, including copying, printing and distribution, but not limited  to, involves the application of the guilty person to civil liability and criminal liability.

Contact information:
1. Manufacturer of goods – OURSSON AG (Orson AG), Rue du Grand-Chêne 5, 1003 Lausanne, Switzerland.
2. Certification information product available on the website www.oursson.com.

OURSSON AG
Made in China
forum.oursson.ruhttp://www.oursson.com/rus/ru/support/recipes/

References

• Oursson Forum • Главная страница
• OURSSON / Oursson
• OURSSON / Oursson

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>