ELEMENT 83.53677 Scale Off Road Bushido Trail Truck Owner’s Manual

ELEMENT 83.53677 Scale Off Road Bushido Trail Truck

Specifications:

• Model: Enduro Trail Truck
• Manufacturer: Element RC
• Transmission: 3-gear with 13.98:1 ratio
• Suspension Design: 4-link with metal pivot balls
• Motor: MT380 Reedy Power motor
• Electronic Speed Control (ESC): FLYSKY 2-1 brushed ESC
• Receiver Unit: Built-in LED lighting controller
• Transmitter: 2.4GHz FLYSKY transmitter

Product Usage Instructions

• Building Your Enduro Chassis:
  Follow the assembly manual provided with the product for step-by-step instructions on building your Enduro chassis. Ensure you have all the necessary items listed in the manual before starting.

• Maintaining Your Enduro Chassis:
  Regularly check and lubricate the drivetrain components to ensure smooth operation. Inspect the suspension system for any wear and tear, and replace parts as needed. Keep the chassis clean from dirt and debris to prolong its lifespan.

• Driving Your Enduro Trail Truck:
  Before driving, ensure the battery is fully charged and all electronics are functioning properly. Start by driving on flat, open terrain to familiarize yourself with the controls. Gradually move to more challenging terrains as you gain confidence in handling the truck.

FAQ:

• Q: What items are needed to build or maintain the Enduro Trail Truck?
  A: The required items include those listed in the assembly manual. Additionally, helpful items like flat head screws (2.5×8 mm) and button head screws (2x10mm) can aid in the building process.

• Q: How can I improve the grip of my Enduro12 chassis on rocky terrain?
  A: The forward-biased motor mount design helps keep the weight over the front tires for better grip. You can also consider adjusting the suspension setup to optimize traction on challenging surfaces.

• Q: What should I do if my Enduro Trail Truck’s electronics malfunction?
  A: If you experience issues with the electronics, first check the connections and batteries. If problems persist, contact Customer Service for assistance or refer to the troubleshooting section in the user manual.

INTRODUCTION

Thank you for purchasing this Element RC product. This assembly manual contains instructions and tips for building and maintaining your new Enduro chassis. Please take a moment to read through this manual to help familiarize yourself with these steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags.

ENDURO TRAIL TRUCK

A performance rig built to endure.
When hitting the trail, you want to do it with confi dence and the answer is the Enduro12 Rock Crawler Trail Truck!

• Don’t let the small size fool you, the Enduro12 chassis is jam-packed with tons of features you’ll be glad to have out on the trail. At the heart is a 3-gear transmission with a 13.98:1 ratio and integrated motor mount. The forward-biased motor mount is designed to keep the weight over the front tires for better grip when climbing out on the rocks.
• Feeding the power to the tires are a pair of low-friction slider-type driveshafts, metal front CVA drive axles, and metal ring and pinion gears. With the Enduro12 drivetrain, delivering useful power and torque will not be an issue.
• Utilizing a 4-link suspension design with metal pivot balls in the front and rear allows for the use of a Servo On Axle (SOA) steering setup. This, paired with metal steering links and pivot balls, allows for precise and direct control over the roughest terrain.
• The Enduro12 Trail Truck comes ready for adventure right out of the box, with performance-driven electronics. The small but powerful MT380 Reedy Power motor supplies smooth and reliable power to the drive train. The FLYSKY 2-1 brushed electronic speed control (ESC) and receiver unit have a built-in LED lighting controller. Together with the 2.4GHz FLYSKY transmitter and Reedy Power servo, control will not be an issue when tackling the rocks.
• With all this packed in one box, we know the Enduro12 Trail Truck is ready for the trail – Are you?

ITEMS NEEDED

The following items are required to build or maintain your Enduro Trail Truck.

• 1.5mm Allen Wrench (#1500)
• 2mm Allen Wrench (#1501)
• 2.5mm Allen Wrench (#1503)
• Pliers
• Long Nose Pliers
• 5.5mm Nut Driver (#1507)
• 7mm Nut Driver (#1508)

OTHER HELPFUL ITEMS
The following items aren’t required but will aid in the building and maintaining of your Enduro Trail Truck.

• Threadlock (#1596)
• Green Slime (#1105)

FEATURES

• Metal front CVA system
• Dual F/R option Battery placement tray with hook-and-loop hold-down strap
• Realistic Scale 8 Hole Chrome wheels with soft compound off-road tires
• 4-link front and rear suspension
• Fully adjustable, threaded, fluid-filled shocks
• Low CG servo Mounting position
• 13.98:1 ratio 3-gear transmission with integrated motor mount
• Composite low-friction slider-type center driveshafts
• Rubber-sealed ball bearing set
• 12mm Wide stance Aluminum wheel hexes
• Durable Hi Torque mini Servo
• Solid Front and Rear Axle

ELECTRONICS:

• 2.4GHz All-in-one Flysky ESC, Transmitter and receiver system
• 850mah Li-Ion 7.4V 2-cell battery and charger
• Reedy Hi-Torque brushed 380 motor
• Reedy Power Hi-Torque Mini Servo

BODY FEATURES:

• Thermoformed high-strength polycarbonate body
• One-piece cab and bed design with fl and fenders
• Dropped bed design.
• Injection-molded front bumper
• Detailed grill and window decals

HARDWARE 1:1 SCALE VIEW

HARDWARE 1:1 SCALE VIEW HARDWARE USED WITH OPTIONAL REPLACEMENT PART NUMBERS

USING THIS MANUAL

QUICK START GUIDE

GATE 01

Battery Charging Steps and Safety:

• Remove the battery from the vehicle before charging. Place the battery on a fi re-resistant surface.
• Avoid any contact with water or other liquids.
• Be sure to select the correct charging mode for the type of battery you are charging (if applicable).
• ALWAYS use a compatible charger for charging your batteries.
• Caution: Never leave the battery unattended while charging. Always disconnect the charger from the power source when fi finished charging.
• Caution: Always disconnect the battery when you are fi finished driving the vehicle.

GATE 02

Battery Installation:

1. Install the battery with the battery wires directed towards the front of the vehicle.
2. Secure the hook and loop strap.

You may move the foam pad to either the front or the rear of the battery compartment to adjust the weight balance of the vehicle.

GATE 03

GATE 04

Battery Notes and Tip:
Connect the battery as shown. Disconnect the battery when not in use!

• LiPo/LiLo: LiPo/LiLo batteries (lithium polymer / Lithium Ion) are high-current rechargeable batteries. LiPo/LiLo batteries offer extended run time and peak performance over NiMH batteries. They require a peak detection charger designed specifically for LiPo/LiLo batteries.
• These batteries require special care and handling.
• LiPo/LiLo batteries are recommended for advanced users only!
• ALWAYS charge a LiPo/LiLo battery in LiPo/LiLo mode.

GATE 05

Radio System Tuning and Controls:

RULE:
Transmitter on First/Vehicle on Second, Vehicle off First/ Transmitter off Last!

1. Slide the battery cover to remove the cover.
2. Install alkaline or rechargeable AA-size batteries into the battery holder.
3. Slide the battery cover back into place making sure it is completely closed and secure.
4. Turn the power ON. If the power indicator LED fails to light, check the batteries for insufficient contact or incorrect polarity.

GATE 06

Radio System Tuning and Controls:

• DO NOT hold the trigger when turning on the radio.
• If using an optional battery for the transmitter, be sure to plug it in correctly. Plugging in a battery backward can cause damage.
• Refer to the Radio owners manual for more in-depth instructions on radio operation and functions.

GATE 07
Install body and body clips. Ready to go!

SHOCK BUILD

GATE 01

GATE 02

NOTE:
Build 4 complete shocks.

Shock Bleeding Steps:

1. Pull the shock shaft down.
2. Fill the shock body 3/4 full with silicone fluid.
3. Slowly move the shock shaft up and down to remove air from under the piston.
4. Wait for bubbles to come to the surface.
5. Fill the shock body to the top with silicone fluid.
6. Place a drop of oil in the cap and on the cap threads.
7. Install capthe  and tighten it partially.
8. Slowly compress the shaft all the way to bleed the excess silicone shock fluid out of the bottom of the shock cap (use a rag around the shock to catch excess fluid).
9. Tighten the shock cap until snug while shathe ft is fully compressed.

GATE 03

CHASSIS BUILD

GATE 01

FRONT AXLE BUILD

GATE 01

GATE 02

GATE 03

GATE 04

REAR AXLE BUILD

GATE 01

GATE 02

GATE 03

GEARBOX BUILD

GATE 01

DRIVELINE BUILD

GATE 01

ELECTRONICS INSTALL

GATE 01

GATE 02

GATE 03

WHEEL/TIRE/BODY BUILD

GATE 01

GATE 02

GATE 03

GATE 04

GATE 05

ASSOCIATED ELECTRICS, INC.

• 21062 BAKE PARKWAY LAKE FOREST, CA 92630 USA
• CALL: 848-544-7500
• FAX: 848-544-7501

CHECK OUT THE FOLLOWING WEBSITES FOR ALL OF OUR KITS, CURRENT PRODUCTS, NEW RELEASES, SETUP HELP, TIPS, AND RACING INFO! WWW.ASSDCIATEDELECTRICS.CDM.

Follow Us On Social Media

www.ElementRC.com.

• AE is a Registered Trademark of Associated Electrics, Inc.
• TEAM ASSOCIATED is a Registered Trademark of Associated Electrics, Inc. REEDY is a Registered Trademark of Associated Electrics, Inc.
• FACTORY TEAM is a Registered Trademark of Associated Electrics, Inc. ELEMENT ™ is a Trademark of Associated Electrics, Inc.
• AREA 51 is a Registered Trademark of Associated Electrics, Inc. STEALTH is a Registered Trademark of Associated Electrics, Inc.
• GREEN SLIME is a Registered Trademark of Associated Electrics, Inc.

References

• Your Journey Begins Here! | Associated Electrics

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>