Learning Educational Toys and Sensory Products Instructions

: August 29, 2024
: Learning

Table of Contents

LED COLUMN
- INTRACTIVE TUBE
- Installation, Operation & Care Manual
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LED COLUMN

INTRACTIVE TUBE

Learning Educational Toys and Sensory Products

Installation, Operation & Care Manual

DIMENSIONS

The LED Column comes in 5 standard sizes:

1.8m, 1.5m, 1.45m, 1.25m & 1m

*These are the overall heights of the unit.

Custom sizes are available upon enquiry, please contact your distributor.

Learning Educational Toys and Sensory Products - a1

PACKAGE CONTENTS

Learning Educational Toys and Sensory Products - a2

1. x1 LED Column Base
2. x1 LED Column Tube
3. x4 Washers
4. x4 Wing Nuts
5. x1 Power Cable & Adapter

INSTALLATION

ASSEMBLY

1. To begin, you will need to remove the white plastic cover from the LED Column Base. Firmly pull the cover up and lift away.

2. Locate the 4 holes on the bottom of the LED Column Tube with the 4 studs on the LED Column Base unit. Ensure that the cables are not trapped and sit in the cutout in the MDF profile.

3. Place a washer, followed by a wing nut, onto each stud and tighten down.

4. Connect the cables from the LED Column Tube to the back of the control box on the base unit.

5. The LED Column Base cover can now be replaced. Lower the cover over the tube and locate back in place on the base unit. Once located, firmly press the cover into place.

OPERATION

1. On/Off Switch

When the LED Column.is plugged into power, use this-button to turn the product on/off.

2. Power Input

Use this to connect the power adapter cable. Use only the power supply included.

3. Sens/Speed/Mode Switch

This switch has multiple functions:

In any moving pattern modes, press up to change the pattern speed. This can be set between 1 – 5 (1 being slow, 5 being fast). Each press will increase the speed until it cycles back round to slow again.
In any sound reactive pattern mode, press up to change the sound sensitivity. This can be set between 1 – 5 (1 being low, 5 being high). Each press will increase the sensitivity until it cycles back round to slow again.
Holding up will calibrate the LED Column to the current room noise level. Hold up until the tube flashes red. When the sampling is complete, the tube will flash green. The tube is now calibrated. A single press up of the switch will now return you to the displayed patterns.
Pressing up in the pattern auto cycle mode (mode 16, see page 10) will change the time interval that each pattern is played for in this mode. There are 5 options: 2 secs, 30 secs, 3 mins, 10 mins, and 30 mins. Pressing the switch once upwards will change to the next time
The 2 second time: interval is included to allow the user to easily determine the current time interval setting. For example: Simply change the time interval to 2 seconds and then press the Speed switch 4 times upwards to reach the 30-minute time interval. The 2 second time interval is not intended for use other than for demonstration purposes only.
Press down to cycle through the 16 LED pattern modes with each press (Visuals on pages 11 – 13).

4. External Switch Input

When an external switch (not included) is connected here, it can be used to switch the pattern mode with each button press.

The LED Column will turn on in the last mode used. The settings from previous use will also be the same.

The product may also be operated with a compatible wireless controller (not included). For more information, please contact your distributor.

PATTERN MODES

The LED Column has 16 pattern modes:

White bubbles/red background travelling upwards
White bubbles/green background travelling upwards
White bubbles/blue background travelling upwards
White bubbles/grey background travelling upwards
Vertical rotating rainbow
Blue/white rotating vertical stripe
Red/white rotating vertical stripe
Rainbow travelling upwards
Gradual fade through a rainbow of colour
Red/white rotating diagonal stripe
Pink/green rotating diagonal stripe
Blue/green rotating diagonal stripe
(Sound responsive) Green column changing to blue in reaction to sound volume
(Sound responsive) Steps through a rainbow of colours with each individual sound made
(Sound responsive) Horizontal bands of colour creep up – the tube but vanish when noise is made
Automatic Cycle (Demo mode) The LED Column automatically cycles through Modes 1-15

The moving speed of the pattern modes can be adjusted, as described on page 7.
An external switch can be connected to the 3.5mm jack socket. With each press it will cycle through the pattern modes (see page 7 & 9).
The sensitivity of the sound reactive pattern modes can be adjusted as described on page 7.
The time intervals of each pattern on auto cycle mode can be adjusted as described on page 8.

TROUBLESHOOTING

The LED Column is designed to be low maintenance.

If problems occur:

Power the tube off, unplug from mains socket and check that power cable is correctly inserted into the unit (see below).
Turn off tube, unplug from mains socket and leave for 1 minute to perform a reset. After this time, plug the tube back into power and turn back on.