Telpo C8 Smart Terminal User Manual

October 30, 2023
Telpo

Telpo C8 Smart Terminal

Telpo-C8-Smart-Terminal-product

Product Information

The C8 Smart Cash Register is an advanced point-of-sale device that can process transactions and provide business insights. The device comes with a 15.6-inch main display, a 10.1-inch customer display, and a variety of peripheral ports for connecting accessories. It runs on a dual-core 1.8GHz + quad-core 1.4GHz processor and supports Android 11 or above operating system. The device has 2GB DDR memory and 16GB eMMC storage, with an external TF card slot for expanding storage capacity. It also has a single-lens camera (with optional dual-lens or 3D depth sensing camera), WiFi/Bluetooth connectivity, and support for smart card and contactless card readers (optional). The device comes with a power adapter and user guide.

TF Card Installation

  1. Take out the back cover, and the card sockets will be shown.
  2. Insert the TF card into the card slot according to the direction shown, and finally close the cover.

Specification

Processor Dual-Core 1.8GHz + Quad-Core 1.4GHz or above
OS Android 11 or above
Memory 2GB DDR, 16GB eMMC, Ext. TF card slot

Display

| Main Display: 15.6-inch, 1920*1080 Customer Display:

10.1-inch, 1280*800 or above

Camera (Optional)| Single-lens Camera Dual-lens Camera
3D Depth Sensing Camera
Communications| WiFi/Bluetooth
Smart Card Reader (Optional)| Support
Contactless Card Reader(Optional)| ISO14443 Type A/B, Mifare
Peripheral Ports| 4 USB, 1 Micro USB, 1 RJ11, 1 RJ12, 1 RJ45,
1 Audio Jack
Audio| Digital Audio Speaker
Power Supply| 12V/3A
Others| 1 Power Key
Environmental| Operating temperature: -5℃ ~ 45℃ Storage temperature: -25℃ ~ 60℃
MDM (Optional)| Mobile Device Management

Accessories

  • Main Device: 1 Set
  • Power Adapter: 1 Piece
  • User Guide: 1 Volume

Before using the device, ensure that all the accessories above are included in the package. If you have any problems, please contact the services provider of the distributors.

Brief Introduction

Telpo-C8-Smart-Terminal-fig-2

I/O interface

Telpo-C8-Smart-Terminal-fig-3

Wire Trimming

  1. Pull the back cover up from the bottom groove.
  2. Thread the wire through the threading hole from below to the corresponding interface under the main screen.
  3. Align the top three clasps of the cover with the column clasps, and then press down the cover.

Power On

  1. Connect the power supply and press the power button to burn on the terminal.

FCC Rules

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals