Spedal CL796W Smart Multimedia Dashcam User Manual
- October 30, 2023
- Spedal
Table of Contents
Spedal CL796W Smart Multimedia Dashcam User Manual
Safety Guidelines
Warnings
- Do not operate this product when driving.
- Do not install or operate this product with wet hands.
- Do not install this product in a place with high temperature, humidity, flammable, explosive gas or liquid.
- Do not install this product in an area that interferes with the driver’s sight or driving safety.
- Do not install this product on the airbag cover or within the working range of the airbag.
- Do not leave this product in a closed vehicle with high temperature for a long time.
- Do not operate this product over rated voltage.
- Do not use non-original cables and accessories.
- Do not use sharp objects such as awls or scissors to cut this product and its accessories.
- Do not disassemble, repair or modify this product and accessories by yourself.
- Do not install, use or place this product within the reach of children under the age of 16.
Precautions
- Do not press the lens too hard to avoid damage or dislocation of the lens.
- Do not directly touch the lens surface, so as not to affect the recording effect.
- Do not remove the memory card during the shutdown process to avoid file damage.
- When using the memory card for the first time, please format it on this product to ensure stable reading and writing.
- When not using the product for a long time, please pull out the memory card to ensure the performance of the memory card.
Preparations For Product Use
Products And Components
| CL796W | Camera | Suction Bracket | Power Cable |
|---|---|---|---|
| USB-A To USB-C Cable | Audio Cable | Camera Cable | TF Card |
| --- | --- | --- | --- |
| Dashboard Pad Mounting Disk | Non-slip Mat | User Manual | |
| --- | --- | --- | |
Note
Do not use non-original cables and components.
Gifts and components are not covered under warranty.
The package contents of this product are subject to change without prior
notice, and the actual package contents shall prevail.
Product Introduction
Installation Guide
TF Card Installation
- Insert the TF card into the TF card slot.
- Please use the TF card that comes with this product.
The self-provided TF card should meet the following requirements: Class 10 or above, the capacity does not exceed 128GB.
Suction Bracket Installation
-
Align the suction bracket clips with the holes on the back of the device and push them up to secure the bracket.
-
Thoroughly clean and dry the car dashboard surface, remove dust or debris, and make sure the surface is flat.
-
Remove the 3M adhesive release paper from the dashboard pad mounting disk and adhere it to a clean instrument panel surface.
-
Allow to sit for 3 hours or more to ensure a strong bond.
Then remove the protective film from the dashboard pad. -
Tear off the protective film from the suction bracket, place the suction cups firmly in the center of the dashboard pad mounting disk, and press the lock button.
-
Adjust the angle of the device screen.
Note
The installation position of equipment and brackets should not block the
driver’s sight and affect driving safety.
Device Installation
Insert the power cable into the car cigarette lighter, and connect the other end to the power interface of the device.
Camera Installation
- Tear off the protective film of the camera lens.
- Peel off the 3M adhesive release paper from the camera mount, attach the camera to the windshield, and press firmly to secure it.
- Connect the device via the camera connection cable.
- Adjust the angle of the camera lens.
Audio Cable Installation
- Insert the audio cable into the car AUX port, and connect the other end to the AUX OUT port of the device.
- Set the car’s audio input mode to AUX audio input.
After the connection is successful, you can play music, navigation, calls and more through your car’s audio system.
CUSTOMER SUPPORT
More product information: www.spedal.cc
Scan Me
More product videos YouTube search spedal.
_ Scan Me
_
For any questions please contact: support@spedaltech.com