Spedal CL796P Smart Multimedia Dashcam User Manual
- June 9, 2024
- Spedal
Table of Contents
Spedal CL796P Smart Multimedia Dashcam
Disclaimer And Safety Guidelines
Disclaimer
Thank you for purchasing this Spedal product. The content mentioned in this
manual is related to your safety and legal rights and responsibilities. Before
using this product, please read this document carefully to ensure proper
product settings. Failure to follow the instructions and warnings in this
document may result in injury to you and people around you, as well as d amage
to this product or other objects nearby. The final interpretation right of
this document and related documents belongs to Shenzhen Xinzhuang Goodo
Technology Co., Ltd. Subject to update without notice. Please visit
http://spedal.cc for the latest product information. Once you use this
product, it is deemed that you have carefully read the disclaimer and
warnings, and understand, recognize and accept all the terms and contents of
this statement. You undertake to take full responsibility for the use of this
product and the possible consequences. Spedal is not responsible for damage,
injury, or any legal liability arising directly or indirectly from the use of
this product. Users should follow all safety guidelines including but not
limited to those mentioned in this article.
Safety Guidelines
Warnings
- Do not operate this product when driving;
- Do not install or operate this product with wet hands;
- Do not install this product in a place with high temperature, humidity, flammable, explosive gas or liquid;
- Do not install this product in an area that interferes with the driver’s sight or driving safety;
- Do not install this product on the airbag cover or within the working range of the airbag;
- Do not leave this product in a closed vehicle with high temperature for a long time;
- Do not operate this product over rated voltage;
- Do not use non-original cables and accessories;
- Do not use sharp objects such as awls or scissors to cut this product and its accessories;
- Do not disassemble, repair or modify this product and accessories by yourself;
- Do not install, use or place this product within the reach of children under the age of 16.
Precautions
- Do not p ress the lens too hard to avoid damage or dislocation of the lens;
- Do not directly touch the lens surface, so as not to affect the recording effect;
- Do not remove the memory card during the shutdown process to avoid file damage;
- When using the memory card for the first time, please format it on this product to ensure stable reading and writing;
- When not using the product for a long time, please pull out the memory card to ensure the performance of the memory card.
Preparations For Product Use
Products And Components
Note: Do not use non-original cables and components. Gifts and components are not covered under warranty. The package contents of this product are subject to change without prior notice, and the actual package contents shall prevail.
Product Introduction
Installation Guide
TF Card Installation
- Insert the TF card into the TF card slot with the metal side facing down.
- Ple ase use the 3 2GB TF c ard that comes with th is produc t. The self-provided TF card should meet the following require ments: Class 10 or above, the capacity does not exceed 128GB.
Suction Bracket Installation
- Align the screw of the suction cup bracket with the screw ho le on the top of the device, turn the suction cup bracket clock wise, and tighten the screw;
- Adjust the angle of the screen and lens of the device;
- Select a suitable position (such as the center of the front windshield), fix the suction cup on the glass, press the locking piece.
Dash Mount Installation
- The wire on the back of the device passes through the dash mount from the hole in the middle of the clip;
- Push up the snap of the dash mount, align with the hole on the back of the device, and fix the bracket;
- Adjust the angle of the screen and lens, Fix the dash mount o n the dashboard;
- Adjust the angle of the screen and lens.
Device Installation
- Insert the power cable into the car cigarette lighter, and connect the other end to the power interface of the device;
- Use suction bracket or dash mount to fix the device. (Refer to [2.3.2 Suction Bracket Installation] / [2.3.3 Dash Mount Installation]).
Rear Camera Installation
- Connect the rear camera to the Rear camera cable – Wire A, and insert the other end into the rear camera port (AV-IN) of the device;
- Use the rear camera bracket to fix the rear camera above the license plate;
- Please tear off the rear camera lens protective film before use;
- Please adjust the lens to a suitable angle. Tighten the screws.
Note: If the Rear camera cable-Wire A(21.3ft) is not long enough, you can use the extension cord-Wire B(16.5ft,- CL796P) or extension cord-Wire B(41ft,CL796T) in the package to extend the connection.
Audio Cable Installation
- Insert the audio cable into the car AUX port, and connect the other end to the AUX OUT port of the device;
- Set the car’s audio input mode to AUX audio input. After the connection is successful, music, navigation, calls, etc. can be played through the audio system in the car.
Features And Settings
Home Screen
Settings Mode
Video Settings
Click “Settings” on the home screen to enter “Video Settings” (driving
record settings).
- Loop recording: Set the time of each recording. 1 minute, 2 minutes, 3 minutes or off can be selected.
- Crash Sensitivity: Set the sensitivity of the gravity sensor. High, medium, low or off can be selected.
- Time Watermark: Set whether to mark the time at the same time when recording. Close or open can be selected.
- Recording sound switch: Set whether to record sound at the same time when recording. Close or open can be selected.
- Exposure: Under different light, you can get better shooting effect by adjusting the EV value. -3, -2, -1, 0, 1, 2 or 3 can be selected.
- Light source frequency: According to different countries or regions, the power line frequency can be set to 50Hz or 60Hz.
General Settings
- Format: Delete all data on the TF card. This operation is irreversible, please back up the images or photos before performing this operation.
- Auto screen off: Set the time for the screen to automatically turn off. 10 seconds, 30 seconds, 1 minute or off can be selected.
- Language setting: Set the language displayed by the system. 简体中文, 繁體中文, English, Français, Español, Português, Deutsch, Italiano, Pусский, 日本 語 or 한국어 can be selected.
- System volume: Set the system volume.
- Key tone: Set whether the key tone is enabled. Close or open can be selected.
- Device Time: Set date, time and date format.
- Restore to factory settings: Restore all settings to the factory default values.
- Device Information: View the current firmware version information of the host.
Carplay Mode
Insert one end of the USB – lighting cable into the mobile phon e, and the
other end into the USB port of the device; after the connection is successful,
the device will enter Carplay mode automatically.
Note:
- Please make sure your iphone version is higher than iOS9;
- If you want to control the device by voice, please open Siri in the iPhone.
Android Auto Mode
Insert one end of the USB – type C cable into the Android phone , and the
other end into the USB port of the device; after the connection is successful,
the device will display the Android Auto working interface, and the mobile
phone will dis play the Android Auto application icon.
Note: Please make sure your Android phone version is higher than Android
11.
DVR Mode
Click “DVR” on the home screen to enter the DVR mode.
Playback Mode
Click “Playback” on the home screen to enter the playback mode, where you can
play, lock, unlock, delete videos or pictures.
FM Mode
Click “FM” on the home to enter FM mode.
- Adjust the car FM to a frequency that is not occupied by the broadcast, and adjust the device FM to the same frequency; for example, adjust the car FM to 91.0MHZ (if not occupied), and then adjust the the FM frequency of the device to 91.0MHZ, as well, and the FM function is turned on; after the connection is successful, the sound on the device will be transmitted to the car speakers.
- When the FM is on, you can select the button or slide the pointer to adjust the frequency.
Note: If you do not need to use the car audio, please set the FM to OFF,
otherwise the device will not output sound.
Download manuals of other languages from our homepage.
more product information www.spedal.cc
For any questions please contact
support@spedaltech.com
more product videos youtube search spedal
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>