Fitcare HRM812S Heart Rate Monitor User Manual
- June 1, 2024
- FITCARE
Table of Contents
HRM812S Heart Rate Monitor
Specifications:
-
Dimensions: 70mm x 100mm
-
Product Type: Heart Rate Monitor
-
Power Source: CR2032 3V battery (lasts approximately one
year) -
Compatibility: ANT+ & BLE Sports System, Bluetooth 4.0 LE
System (iOS 9.0+ and Android 4.3+)
Product Usage Instructions:
1. Getting Started:
To wear the chest strap:
-
Wet the conductive pads on the rear of the chest belt with
water, saliva, or conductive gel for good contact. -
Strap the heart rate chest belt across your chest snugly below
your pectoral muscles. -
Attach the transmitter to the strap with the ‘L’ marking
towards the left side.
2. Battery Replacement:
-
Twist the battery door counter-clockwise using a coin to remove
it. -
Replace the old CR2032 3V battery with the positive side facing
upwards. -
Twist the battery door clockwise to secure it in place.
3. Ready to Use:
If successfully paired, the device is ready for use with
Bluetooth 4.0 LE System on compatible iOS and Android devices.
4. Data Transmission:
The HRM supports ANT+ & BLE Sports System for reliable data
transmission. For ANT+ System pairing:
- Ensure HRM battery is not drained and replace if needed.
- Avoid other ANT+ transmitting devices within a 50m range during
pairing process.
FAQ:
Q: Is the heart rate monitor waterproof?
A: The heart rate monitor is water-resistant but not waterproof.
Avoid submerging it in water.
Q: How do I clean the chest strap?
A: Use a damp cloth with mild soap to clean the chest strap. Do
not soak it or use harsh chemicals.
70 mm
100 mm
Heart Rate Monitor
USER MANUAL
1
Thank you for using this product as your sports fitness product of choice. The
product is a sensor type heart rate monitor that will track your real-time
heart rate and send heart rate data to the Smart phone.
IMPORTANT This product is for sport purposes only and it is not meant to
replace any medical advice.
This manual contains important safety and care information, and provides step
by step instructions for using this product. Read it thoroughly, and keep the
manual in a safe place in case you need to refer to it later.
2
DEVICE OVERVIEW:
A. Heart rate Transmitter a. Front View
B. Heat rate chest strap
3. Electrodes 4. Fastening buttons C. Smart phone (Sold separately)
GETTING STARTED
A. Unpacking the product In this box, you will find: a. Heart rate transmitter
b. Adjustable elastic belt c. CR2032 battery already installed d. User
manual
5
B. To wear chest strap a. Wet the conductive pads on the rear of the chest
belt with a few drops of water, Saliva or conductive gel to ensure solid
contact.
6
b. Back View
1. Battery Door
2. Left & Right wearing directions
3
4
b. Strap the heart rate chest belt across your chest. To ensure an accurate
heart rate signal, adjust the strap until the belt fits snugly below your
(chest) pectoral muscles.
c. Attach the transmitter to the strap, marked `L’ towards left.
7
8
WARNING Inaccurate heart rate data will be detected if the device is worn in
wrong directions.
C. To run software on smart phone, receive the heart rate data.
9
IMPORTANT 1. Non-rechargeable and rechargeable batteries must be disposed of
properly. For this purpose, special containers are provided for battery
disposal at communal collection centers. 2. Batteries are extremely dangerous
when swallowed! Therefore, keep batteries and small articles away from
children. 3. The batteries supplied must not be recharged, reactivated by any
other means, dismantled, put into fire or short-circuited.
13
WARNING a.Cleaning of transmitter and strap in a washing machine or dryer is
strongly prohibited. b.Before hand washing the device, detach the transmitter
of Heart Rate Monitor where electrodes are located, This part is not washable.
c.While washing the straps, make sure water is no higher than 30¥. d.Ironing,
bleaching or heating is prohibited
10
DATA TRANSMISSION
ANT+&BLE Sports System is supported to achieve reliable data transmission by
this HRM. For ANT+ System:
A. Pairing If the HRM is not paired with the ANT+ compatible receiver, it has
to be activated and paired. > Ensure that the HRM battery is not drained.
Replace the battery if needed. > Ensure there are no other ANT+ transmitting
devices within 50 m range, other devices may affect pairing.
14
BATTERIES
The transmitter use CR2032 3V battery. The battery already installed. The
battery typically last one year .
A. Using a coin, twist the battery door counter clockwise until it clicks out
of place.
B. Remove the old battery and insert the new battery with the +side upwards. C. Replace the battery door by twisting it clockwise until it is firmly in place.
11
B. Ready to use
If your device is successfully paired, it’ s ready for use. For Bluetooth 4.0
LE System:
A. This device is a Bluetooth Smart device, compatible and applicable with
many IOS devices, including:
iOS 9.0 version and above, iphone 5 and above. Any Bluetooth 4.0 enabled
Android device with Android 4.3 and above .
15
12
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
16