dewenwils HRLS11C1 Wireless Remote Control Outlet Instruction Manual

**dewenwils HRLS11C1 Wireless Remote Control Outlet Instruction Manual

**

Please pay attention to the warning signs
Read the instructions with caution before operating and keep it properly

Warning:
To reduce the risk of fire, electric shock or personal please strictly follow the instructions.

1. For indoor use only. Avoid high humidify, high temperature and high magnetic field
2. Do not connect any devices that may exceed the performance limits of the outfit,
3. Do not insert needles or any other metal objects note mains outlets
4. Dot not disassemble o repair the product, but oily by authorized service personnel.
5. Children are not allowed to use remote outlets without adult supervision, prevent chidden from suffocation and chocking, keep them away from packing materials
6. Do not use the battery again if i is dropped or knocked out of shape.
7. Used batteries should be disposed of safely and in accordance with environmental protection standards.

Product lustration

Operating Instructions

1.  Plug the receiver into powered outlet
2. Remove he section ab n the baler compartment of the rangier
3. Pass each ONIOFF baton on he transmitter ill tum on o off the core spending receiver accordingly

Note:

1. Program button of each receiver can also be used as manel swish.
2. The receiver will romaine “OFF” ate a power cu t save energy.

Canceling Programming

To remove a receiver from al transmitter parings (10 emote transmits can control )

1. Unplug the connected device form receiver
2. Unplug the receiver rom the powered outlet
3. Pross and hold the program button on the receiver
4. Plug the receiver back of powered outlet while continuing 0 press the program button for approximately 5 seconds unfit the nicator begins to fiat.
5. Program reset I successful when the nicator on receiver flashes several limes ‘and stops inking

Programming the Receiver

The receivers and transmitter have been pre-paired for immediate use, but there are few units may not be pre-programmed or programmed incorrectly, or you want to customize the configuration to meet your needs. To program a transmitter and receiver, please follow the steps below:

1. Cancel the programming referring to the above ‘Cancelling Programming’ section firstly.
2. Press the program button on the receiver for 6 seconds until the indicator light starts to flash slowly.
3. Release the program button and then press the “on” or “off “button on the remote control.
4. Programming / paring is successful when the indicator light stops blinking.

Note:
Each set of ON or OFF button can be paired with and control several outlets:
Each outlet can be paired with and controlled by multiple transmitters.

Mounting the Wall Switch
Shown as the figure

Battery Replacement:

1. In you find the receivers work abnormally or the indicator on the transmitter becomes dim, please replace the remote battery with a new DC 12V (type 23A) battery, making sure the polarity + / – of the battery is correct.
2. Low battery power may decrease readable wireless remote range.
3. Remove batteries if the remote is not in use for an extended period of time.

Troubleshooting

In the case that one receiver is unresponsive to the remote control, please follow the steps below to resolve the issue:

1. If the wire switch receiver is unresponsive to the remote control, please refer to the “Canceling Programming” and “Programming the Receiver’ sections in the manual to reprogram the receiver.
2. Make sure the receiver and appliance are properly connected and powered on.
3. Replace the remote battery with a new 12V (23A) battery.
4. The remote transmitter may be too far away to control the receiver. 5. Make sure not to exceed the maximum load.

Specifications

• Input Voltage: 120VAC, 60Hz – Max Power Rating: 10A, 1200W
• Transmission Frequency: 433.92MHz
• Remote Control Range: 100Feet (Free Area)
• Remote Battery: 23A, 12V

Safety Information

Federal Communications Commission Interference Statement. This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Redirect or relocate the receiving antenna.
• Increase distance between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

ISEDC Warning:
This device complies with Innovation, Science, and Economic

Development Canad licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.

One Year Limited Warranty

Supported by our professional R&D team and QC team, we provide One Year Warranty for materials and workmanship from the purchase date. Please note that the warranty does not cover damage caused by personal misuse or improper installation.

Please attatch your Order ID and Name so that our dedicated customer service team can help you better.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>