amazon basics BOB5DF7HKV Projection Alarm Clock User Manual

User Manual

Projection alarm Clock

Improtant Safety intructions

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.
When using electrical products, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons including the following:
Hearing damage risk!
To prevent possible hearing damage, do not  listen at high volume levels for long periods.
caution Risk of injury!
Do not look directly into the light from the projection lens to avoid eye injuries.

•  Read Instructions – All the safety and operating  instructions should be read before the product is operated.
• Retain Instructions – The safety and operating instructions should be retained for future reference.
•  Heed Warnings — All warnings on the product and in the operating instructions should be adhered to.
• Follow instructions ~ All operating and use instructions should be followed.
• Cleaning – Unplug this product from the wall outlet  before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
• Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.
• Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or  laundry sink, or laundry tub; in a wet basement; or near aswimming pool; and the like.
• Power Sources – This product should be operated only by  the adapter model GKYPNO200050UL2 supplied with the product.
•  Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spilt liquid of any kind on the product.
•  Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service  personnel under the following conditions:

— If liquid has been spilled, or objects have fallen into the product,
— If the product has been exposed to rain or water,
— If the product does not operate normally by following the operating instructions. Adjust only those controls  that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, and
— If the product has been dropped or damaged in any way.
b Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Battery Warnings

WARNING

DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD.
WARNING

• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.

•  This product contains a coin/button cell battery. If the coin/button cell battery is swaltowed, it can cause severe internal burns in just 2 hours and can lead to death.
  Biff you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
  7 Uh ErOl Et Risk of explosion!
  Risk of explosion if the battery is replaced by an incorrect type.

• Exhausted batteries should be immediately removed from product and property disposed.

•  Do not dispose of batteries in fire.

•  Remove batteries from product if it is not to be used for an extended period of time.

• If the battery leaks avoid contact with skin and eyes. Rinse affected areas immediately with plenty of clean water, then consult a doctor.

Explanation of Symbols

| This adapter is classified as protection class 2. This means the adapter is equipped with reinforced or double insulation between the mains supply circuit and the output voltage or the casing. Therefore it does not require
a safety connection to an electrical earth (ground).
---|---
| This adapter is for indoor use only.
****| This adapter complies to US energy efficiency VI standard.
| Direct current (DC).
∼| Atrenating current (AC)

Intended Use

• This product is intended for household use only.
• This product is intended to be used in dry indoor areas only.
• This product is equipped with a USB port for charging smartphones or other mobile devices.

Product Description

5.1 Top and bottom view ![amazon basics BOB5DF7HKV Projection Alarm Clock

• Battom](https://manuals.plus/wp-content/uploads/2023/06/amazon-basics- BOB5DF7HKV-Projection-Alarm-Clock-Battom.jpg)

  1.   button (SLEEP)

  2. button (ALARM 1)

  3.   button (SNOOZE)

  4. 11 button (ALARM 2)

  5. Focus adjustment ring

  6. Projection lens

  7. Projector arm

  8. dial (backlight)
     5.2 Rear view

  9. Speaker

  10. Battery compartment

  11. Volume dial

  12. Antenna

  13. Antenna holder

  14. Audio-out socket

  15. Type-C port

  16. RESET button 411)

  17. USB charging port
      5.3 Side view

  18.  dial (projection dimmer

  19. project control button

  20. DST button

  21. 12/24 button

  22. MEM button

  23. T_ button fp

  24. T+ button ED

  25. /Fm switch
      5.4 Accessories

  26. Charging cable

  27. Power adapter

Before First Use

DANGER
Risk of suffocation)
Keep any packaging materials away from children and pets – these materials are a potential source of danger, e.g. suffocation.

• Remove all the packing materials.
• Remove and review all components before use.
• Check the product for transport damages.
•  The product contains a CR2032 coin battery pre-installed in the battery compartment (10) as a backup for storing the clock and alarm setting. Remove the battery pull tab from the battery compartment (10} (Fig. 1) before use.

Operation

7.1 Connecting to a power supply

• The product is powered by the power adapter (27).
• The product contains a coin battery as a backup power source to keep the clock and the alarm setting during a power interruption. The battery cannot power the display.
• Always keep a coin battery in the battery compartment (10). When the charging cable (26) is disconnected from the product and the battery is exhausted or removed from the product, the current time and alarm setting will be erased.

1. Connect the USB-C connector of the charging cable (26) to the Type-C port (15) (Fig. 2).
2. Connect the USB-A connector of the charging cable (26) to the power adapter (27), then to a suitable wall outlet (Fig. 2).
3. The display lights up when the product is powered.

7.2 Changing battery

NOTICE

• A coin battery is used as a backup for storing the clock and alarm setting during a power interruption.
• When changing the coin battery, do not disconnect the charging cable (26) from the product and the wall outlet. Otherwise the current time and alarm setting will be erased.
• Always insert the coin battery correctly with regard to polarity (+ and —) marked on the coin battery and the product.
• It is recommended to change the coin battery every 6 months.

1. Fully loosen the screw and open the battery compartment (10) cover (Fig. 3).
2.  Pry the ald coin battery out.
3. Insert a new CR2032 coin battery into the battery compartment (10) with its marking side facing up (Fig. 4).
4.  Refit the cover and tighten the screw.

7.3 Adjusting the display backlight
Turn the x dial (8) to adjust the brightness of the display backlight.
7.4 Adjusting the projection
NOTICE |The clock time can be projected onto a flat and level surface, such as a wall or ceiling within a distance between 5 ft. and 10 ft. (1.5 m and 3 m), preferably in a dark room.

1. Press the button (19) to switch the projection on.
2. Swivel the projector arm (7) from the front to the back (Fig. 5).
3. Press again to flip to an upside down projection when the projector arm (7) is swiveled to the back.
4. Rotate the focus adjustment ring (5) to adjust the sharpness of the projection.
5. Turn the c& dial (18) to adjust the brightness of the protection.
6. To switch the projection off, press the ¢34′ button (19).

7.5 Daylight saving time (DST) mode

• To activate the DST mode, press the DST button (20).
  The clock time changes from standard time to DST. The display shows DST.

•  To deactivate the DST mode, press the DST button (20). DST disappears from the display. The clock time changes from DST to standard time.

7.6 Hour system
Press the 12/24 button (21) to toggle between 12-hour and  24-hour format
NOTICE _| when the product is set to 12-hour format, the display shows AM or PM next to the hour digits. 7.7 Setting clock time
NOTICE

• Each step should be performed within 6 seconds. When no button is pressed within 6 seconds, the product exits the setting mode automatically.
• When setting hour and minute time, press and hold the T- button (23) or T+ button (24) for a speedy adjustment.

1. Press and hold the MEM button (22) until the hour digits start to flash. The product enters time setting mode.
2.  Use the T- button (23) and T+ buttan (24) to adjust the hour time.
3. Press the MEM button (22) to confirm the hour time. The minute digits start to flash.
4. Use the T- button (23) and T+ button (24) to adjust the minute time.
5. Press the MEM button (22) to confirm the minute time. 

7.8 Setting alarm time
NOTICE

• Set the clock time properly before setting the alarm time.
•  The product allows to set 2 different alarms. Perform the same steps below to set the first and second alarm.
• When setting hour and minute time, press and hold the T- button (23) or T+ button (24) for a speedy adjustment.

1. Press and hold the button (2) or button (4) until the hour digits start to flash. The product enters alarm setting mode.

2. Use the T- button (23) and T+ button (24) to adjust the hour time.

3.  Press the button (2) or button (4) to confirm the hour time. The minute digits start to flash.

4. Use the T- button (23) and T+ button (24) to adjust the minute time.

5. Press the   button (2) or   button (4) to confirm the minute time.

6. Press the T+ button (24) to select between BUZZ and RADIO for the alarm signal type.
   NOTICE | when the alarm time is reached:
   » BUZZ: The product starts to ring.
   » RADIO: The radio station last listened starts to play.

7. Press the   button (2) or   button (4) to confirm the alarm signal type.
   NOTICE | if BUZZ is chosen, use the T- button (23) and T+ button (24) to set the volume of the alarm signal (bt: High; be : Natural (default setting); b3 : Low).

8. Press the   button (2) or button (4} to complete the alarm time setting. The steady display shows the corresponding icon(s) {21 and/or (92 2.

7.8.1 Activating/deactivating the alarm

• To activate the set alarm, press (7 button (2) or £2 button (4) in display mode. The display shows the corresponding icon(s) {91 and/or 22.
• To deactivate the set alarm, press fi? button (2) or  2 button (4) in display mode. The corresponding icon(s) $941 and/or {2 disappear(s) from the display.

7.8.2 Switching off the alarm signal

Press any button other than the button (3) to tun the alarm signal off. The alarm signal lasts for 30 minutes if no button is pressed.
NOTICE |The alarm signal will sound again at the set alarm time on the next day. Deactivate the alarm when needed.

7.8.3 Snooze function

1. When the alarm signal sounds, press   button (3) to activate the snooze function.
2. Use the T- button (23) and T+ button (24) to set the snooze time between 2 and 60 minutes. The default snooze time is 9 minutes.
3. Press zZ” button (3) to confirm the snooze time. The alarm signal sounds again when the snooze time has passed. NOTICE |The snooze function can be activated 5 consecutive times. After that, the alarm will be deactivated.

7.9 FM radio
NOTICE

• To listen to the radio from an external device, connect the 3.5 mm plug of the device to the audio-out socket (14).
•  When no button is pressed in 10 seconds in radio mode, the product returns to display mode and the display shows the current time.

1. Set the /FM switch (25) to FM position.

2. Unwind the antenna (12) from the antenna holder (13).

3. Hang the antenna (12) to a high place.

4.  To search a FM radio station, press the T- button (23) or T+ button (24) to decrease/increase the searching frequency.
   NOTICE | Press and hold the T- button (23) or T+ button (24) to search a radio station automatically.

5. Turn the volume dial (11) to adjust the radio volume.

6. To turn the radio off, set the (   /FM switch (25) to position. 

7.9.1 Storing the radio station

NOTICE |The product can store up to 15 radio stations.

1. When a radio station is found, press and hold the MEM button (22) to open the radio station list.
2.  Press the T- button (23) or T+ button (24) to assign a desired number for the station.
3.  Press the MEM button (22) to confirm.

NOTICE | Press MEM button (22) repeatedly to select the saved radio station. The display shows the station number between P{ and P1S and the FM frequency of the Stored radio station.
7.9.2 Setting a sleep timer
Set a sleep timer to switch the radio off automatically.

1. Set the   /FM switch (25) to FM position.
2. Press the   button (1) once to enter the setting.
3.  Press the button (1) repeatedly to select the desired time between OFF, 5, 10, 15, 30, 45, 60, 75 and 90 minutes.
4. Wait for 3 seconds and the selected option is saved. The display shows SLEEP.

7.10 Charging function

To charge an external device, connect a USB cable (not included) to the device and to the USB charging port (17).
7.11 Factory reset
To perform a factory reset, press the RESET button (16) using & paper clip or needle (not included).

Cleaning and Storage

WARNING
Risk of electric shock!
1 To prevent electric shock, unplug the product before cleaning.
1 During cleaning do not immerse the product in water or other liquids. Never hold the product under running water.
8.1 Cleaning

• To clean the product, wipe with a soft, slightly damp cloth.
• Wipe the product dry after cleaning.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.

8.2 Storage

• Disconnect the charging cable (26) and remove the battery if the product is not intended to use for an extended period of time.
• Store the product in its original packaging in a dry area. Keep away from children and pets.

Frequent y Asked Questions

the wall outlet. Use voltage tester to verify if the socket outlet is powered.
The display is too dark.|  Turn the dimmer dial at the bottom of the product clockwise to increase the brightness of the backlight. I Move the product away from strong light.
The radio reception is poor.| I Fully extend the antenna for clearer reception. 1 Place the antenna away from other AV equipment, such as digital music player or mobile phones. 1 Place the antenna close to a window as high as possible to avoid interference from materials used in wall construction.
The display flickers.| Place near a dehumidifier or fan heater to remove excessive moisture. II Move the product away from any appliances causing electromagnetic interference.

FCC — Supplier’s Declaration of Conformity

10.1 FCC Compliance Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

10.2 FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: I Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio / TV technician for help.

Canada IC Notice

This Class B digital apparatus complies with Canadian CAN ICES-003(B) / NMB-003(B) standard.

Battery Disposal

Do not dispose of used batteries with your household waste. Take them to an appropriate disposal/collection site.
To learn more about recycling batteries, visit: call2recycle.org/what- can-i-recycle

Specification

13.1 product

5 V – 2 A
Charging output (USB port)|
5 V — 1.5 A
Backup battery| 3 V = (CR2032 coin battery)
Projection distance| 5 to 10 ft. (1.5 to 3 m)
FM station frequency| 87.5 to 108 MHz
Audio out| 3.5 mm
Operating temperature| +40 to +90 °F (+5 to +35 °C)
Storage temperature| +40 to +90 °F (+5 to +35 °C)
Charging temperature| +40 to +90 °F (+5 to +35 °C)
Net weight| approx. 0.59 lbs (268 g)
Dimensions (W x H x D)| approx. 1.8 x 3.64 x 7.17″ (4.57 x 9.25 x 18.2 cm)

13.2 Power adapter

Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.
Scan QR Code below with your phone camera or QR reader:

If you need help with your Amazon Basics product, please use the website or number below.
amazon.com/gp/help/customer/contact-us
+1 877-485-0385

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>