VISUAL COMFORT CHC 5877 Darlana Medium Wrapped Lantern Instruction Manual

VISUAL COMFORT CHC 5877 Darlana Medium Wrapped Lantern

Product Information

The Darlana Medium Wrapped Lantern is a light fixture that requires assembly and installation. It comes with a mounting plate, collar loop, chain, canopy, bottom frame, top fixture frame,  threaded caps, rods, tubes, quick links, and fixture wires. The product does not include bulbs. It is important to inspect the item and its contents carefully before installation and to follow all applicable local installation codes. This product should be installed by a person familiar with its construction and operation
as well as the hazards involved.

Product Usage Instructions

1. Remove all parts from the box and place them on a clean, soft surface.
2. Remove collar loop (D) from chain (H) by removing quick link (G).
3. Install mounting plate (B) to the junction box and secure it with mounting screws (C).
4. Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.
5. Install canopy (E) to collar loop (D) and secure it with collar ring (F).
6. Thread rods (M) to the bottom frame (N), then let tubes (K) pass through rods (M) and rest on bottom frame (N).
7. Install top fixture frame (N) to the top of the rods (M) and secure it with screws (J), then install threaded caps (P) to top frame (N).
8. Determine desired overall length and amount of chain (H) needed. Shorten chain using chain pliers. Keep extra chain.
9. Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (G). Secure quick links (G).
10. Hang fixture cluster (J) to hook on the bottom of fixture loop (I), then pass fixture wires through the hole in fixture frame.
11. Thread fixture wire and ground wire through chain (H). When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.
12. Separate two sides of molded wire and strip insulation on each 5/8.
13. Loosen collar ring (F) and let canopy (E) slip down chain (H) carefully.
14. Twist all fixture wires together and slip through the center hole of collar.

Care Instructions
Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Darlana Medium Wrapped Lantern
Item # CHC 5877
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED)

• Phillips Screwdriver
• Slip Joint Pliers
• Wire  Strippers
• Slotted Screwdriver
• Measuring Tape
• Chain Pliers
• Wire Cutters

Assembly Instruction

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove collar loop (D) from chain (H) by removing quick link (G).

3. Install mounting plate (B) to the junction box and secure with mounting screws (C).

4. Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.

5. Install canopy (E) to collar loop (D) and secure with collar ring (F).

6. Thread rods (M) to the bottom frame (N), then let tubes (K) pass through rods (M) and rest on bottom frame (N).

7. Install top fixture frame (N) to the top of the rods (M) and secure with screws (J), then install threaded caps (P) to top frame (N).

8. Determine desired overall length, and amount of chain (H) needed. Shorten chain using chain pliers. (Keep extra chain)

9. Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (G). Secure quick links (G).

10. Hang fixture cluster (J) to hook on bottom of fixture loop (I), then pass fixture wires through the hole in fixture frame.

11. Thread fixture wire and ground wire through chain (H).
    NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.

12. Separate two sides of molded wire, and strip insulation on each 5/8″.

13. Loosen collar ring (F) and let canopy (E) slip down chain (H) carefully.

14. Twist all fixture wires together, and slip through center hole of collar loop (D).
    NOTE: Untwist wires and separate to prepare for connection.

15. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
    NOTE: It is imperative that the fixture is grounded.

16. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).

17. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A).
    CAUTION: Do not reverse the hot and neutral connections.

18. Make sure all wire connections are tight, then carefully tuck into the junction box.

19. Install canopy (E) to collar loop (D) and secure with collar ring (F).

20.  Install light bulbs into the sockets.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>