DAEWOO WIS501S Indoor Siren Instruction Manual

DAEWOO WIS501S Indoor Siren

• This logo indicates that products, which are no longer in use, should not be thrown away as household waste. They may contain substances that are harmful to health and the environment.
• Return the product to your reseller or use the recycling collection service provided by your city.
• Liz Invest SAS, 6 Rue Léon Morane, 33700, Mérignac, France hereby certifies that Daewoo Alarm System with CE marking are compliant with the following directive issued by the Commission of the European Community.
• EMC Directive: (2014/30/EU) / (2014/53/EU)
• The low voltage directive: (2014/53/EU)
• RED Directive: (2014/53/EU)
• RoHS Directive: (2014/65/EU)
• Compliance with these directives implies compliance with the following European test standards
• EN300 328 V2.1.1 ( 2016-11) ;
• EN300 220-1 V3.1.1 (2017-2);
• EN300 220-2 V3.1.1 ( 2017-02);
• EN301 489-1 V2.1.1 ( 2017-02);
• EN301 489-17 V3.1.1 ( 2017-02) EN62749:2010
• EN62311:2008 EN62368-1:2014+A11: 2017
• Authorized representative.
• David HADDAD, President.
• Date: 18-March-2020

Features

The Indoor Siren can be used either as an additional siren connected to your alarm system or as an independent siren connected to a remote control and/or wireless detectors.

• Wireless connection for an easy installation
• Radio-frequency security of the accessories: more than one million of codes combinations
• Simplified connection to accessories
•  Can be connected to all of eTiger Secual accessories
• Built-in 3.7V / 300 mAh lithium batteries: 8-hour battery life in standby mode

Box Content

• 1 x Indoor Siren
• 1 x User Manual

Layout

General information

• The Indoor Siren is powered by its built-in AC 90 ~ 240V plug.
• Several Indoor Siren can be installed throughout your home and connected to your alarm system. When the alarm of your system is triggered, the Indoor Siren rings out and its LEDs switch on.
• The Indoor Siren can also be used as a standalone siren and can be connected to wireless sensors and/or to a remote control.

Power on / off

• Power on
  Plug the siren to a AC 90 ~ 220V socket. The light will turn on. You can also turn the siren on by long pressing (6 seconds) the on the siren.

• Power on
  Press the Power button for 6 seconds to turn the siren off.

Siren and light indications

• When arming the system
  The LED lights blink red once per second and blue light is switched on.

• When arming the system in home mode
  The LED lights blink red twice per second and blue light is switched on.

• When disarming the system
  The blue light is switched on.

Use as an additional siren

If the siren is used as an additional siren, it must be registered to your alarm’s control panel. If the alarm is triggered, the sensors and/or to a remote control. will ring out and its LED lights will turn on.

• Register the Indoor Siren in the control panel

  • Press the button on the siren. The siren beeps once and the LEDs light up: the siren is now in Connection Mode for 20 seconds.
  • Press the “Home” or “Arm” button on the control panel of your alarm system.

• Note
  Do not trigger an alarm with a sensor when registering the siren in the control panel. If you have set a delay on your control panel, please temporarely remove the delay before installing your siren.

• Test
  Press the “Arm” button on the control panel. Both the built-in siren of the control panel activate.

Use as a standalone alarm system

• Before using the siren as a standalone alarm system, it must be connected to
  a remote control or an accessory (e.g. motion detector, door / window contact).

• When the system is armed, if a sensor is triggered, the siren will ring out and the LED lights will turn on.

• Connect a remote control

  • Press the Connect button on the siren. The siren beeps once and the LEDs light up: the siren is now in Connection Mode.
  • Press any button on the remote control.
  • You hear one beep: the remote control has been connected to the siren successfully (if you hear 2 beeps, the remote control has already been connected).

• Connect a wireless sensor

  • Press the Connect button on the siren. The siren beeps once and the LEDs light up: the siren is now in Connection Mode.
  • Trigger the sensor (e.g. walk in front of the sensor if you want to connect a motion detector)
  • You hear one beep: the accessory has been connected to the siren successfully (if you hear 2 beeps, the accessory has already been connected).
  • The siren supports up to 10 remote controls and 10 wireless detectors.

Test

• Test the connection to a remote control
  Press the “Arm” button on the remote control. The siren beeps once: the connection of the remote control is successful. If not, the connection has failed, try registering the remote control again.

• Test the connection to a wireless sensor
  Arm the system. Trigger the sensor (e.g. walk in front of the sensor if you have connected a motion detector). The siren rings out: the connection of the sensor is successful. If not, the connection has failed, try registering the sensor again.

Clear all accessories and reset

Press the Connection button on the siren for 6 seconds until you hear five beeps. The LEDs blink twice: all the accessories and control panels connected to the siren have been cleared.

Set the Siren duration

• Short press the button to set the siren duration.
• Press once to set duration to 1 minute, the siren will beep once. Press twice to set the duration to 2 minutes, the siren will beep twice.
• Press 3 times to set the duration to 3 minutes, the siren will beep 3 times.

Specifications

• Power supply: AC 90 ~ 220V
• Volume: 90dB
• Backup battery: 3.7V / 300mA Lithium-Polymer
• Static current: < 15mA
• Alarm current: < 260mA
• Working Distance : 80m
• Radio frequency: 433MHz (±75K Hz)
• Housing material: ABS plastic
• Operating conditions: Temperature: 0°C ~ +55°C
• Relative Humidity: 80% (noncondensing)
• Dimensions: 70 x 70 x 70 mm

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>