AD205 Child Digital Microscope User Manual
- June 13, 2024
- Digital Microscope
Table of Contents
AD205 Child Digital Microscope
Digital Microscope AD205
Product Information
Basic Parameters
Image sensor| 2Mega Pixels HD Sensor
Video output| FHD1920X1080 30FPS; 1080P 1440X1080 30FPS
Video format| 720P 1280X720 30FPS, AVI
Magnification Ratio| Up to 200 times
Photo resolution| MAX 12M (12M 40323024) JPG
Photo format| JPG
Focus distance| 1.5CM-5CM
Frame Rate| Max 30f/s
Storage| Micro-SD card, up to 64G
PC support| No USB
Power source| USB 5V 1A; Support 18650 battery (not included)
Stand size| 1812*11.5CM
Screen size| 5 inch; LCD
Screen resolution| Not specified
Product Usage Instructions
Quick Start
To troubleshoot if the display freezes, locate the reset hole on the back
of the monitor. Use a narrow object such as an unfolded paperclip to depress
the button located inside. This resets all settings to their factory values
and restarts the display. It does not erase saved images or video.
Adjusting the Magnification and Focus
Use the large knobs (Colored knob) on the bracket to raise or lower the
optical stack to the desired height. The lower the height, the greater the
magnification is. But be careful not to let the bottom of the stack contact
the object being imaged. Turn the Focus controller to focus the image. To
increase the digital magnification, press and hold the Up button (Button’) until the desired digital magnification is reached. Use the Down button (V
Button’) to decrease the digital magnification.
Using a Micro SD Card to Save Images
Insert a micro SD card into the designated slot to save images captured by
the microscope.
Reviewing and Managing Images
In each mode, press the M button and hold it for a while until the
Video/Still image/Review Menu shows up on the display (or you can press MENU
button on the remote). Short press M button again to get into the general
Setup Menu. For example, if you are in Video standby mode, and you long press
MENU, the Video menu would show. Then, press MENU button (or M on the monitor)
again to get into the Setup menu. Use the provided buttons to navigate through
the settings menus.
Date and Time Settings
To set the date and time, enter the Setup menu and select the Date/Time
option. Use the provided buttons to select the correct number for
year/month/day. Once you finish setting a number, press OK on the monitor to
move to the next number. Alternatively, you can use the provided remote to
navigate through the options. Press MENU button on the remote to exit
date/time setting directly. Note that if you don’t have the remote, you will
need to go through all the settings one by one and then press OK again to
exit. To save settings, turn off the device by pressing the ON/OFF button on
the monitor and hold it until the device switches off. If you turn off the
device by cutting off the power supply, the settings would not be saved.
Preface
- Please read this manual before use the microscope. If you do not follow the instructions, it‘s possible to cause the device damaged.
- The assembly includes small parts, particularly the thumbscrews used to hold the main device in place. Do NOT allow unsupervised access by infants or toddlers.
- The microscope is not intended for field use. It is not waterproof, and should not be exposed to extreme temperatures. Users can refer to the preservation management methods of general electronic equipment, such as laptops.
- Keep the microscope in a clean and dry environment. Keep away from oil, water, gas and other materials that may cause corrosion.
Basic Parameters
What’s in the box
(P1, buttons & packing contents )
(P2, remote buttons)
Quick start
Note
- To give you good experience, please adjust the microscope and plastic bracket before using, then remove the screen guard film on the screen.
- If the light barrier is not over the bottom light, please adjust its position.
Connect
Firstly, connect the optical stack to the power supply via the switch cable.
See the picture(P3) above. This microscope supports battery(18650), it’s not
included in the package, please purchase separately.
Switch on
- Then press and hold the Power button (on/off ) underneath the display until the display turns on.
- (It may turn on automatically while connecting cables at the first time, and it’s totally fine. )
Troubleshooting
If the display freezes, locate the “reset ” hole on the back of the monitor. Use a narrow object such as an unfolded paperclip to depress the button located inside. This resets all settings to their factory values and restarts the display. It does not erase saved images or video.
Adjusting the Magnification and Focus
- Use the large knobs (Colored knob) on the bracket to raise or lower the optical stack to the desired height. The lower the height, the greater the magnification is. But be careful not to let the bottom of the stack contact the object being imaged. Turn the Focus controller to focus the image.
- To increase the digital magnification, press and hold the Up button (‘Λ Button’ ) until the desired
digital magnification is reached. Use the Down button( ‘ V Button ’ ) to decrease the digital magnification.
Using a Micro SD Card to Save Images
By using a Micro SD card (not provided, please purchase separately), you can
save images and videos to review later or export to a computer or other device
.
Insert the Micro SD card in to the TF slot on top back of the monitor. (be
careful with the direction. The side which has metal exposed should face down.
See the picture 6 ) Push it in until you hear a click.(If you don’t push it in
far enough, it will be ejected. )
The ‘M’ button (Mode button) can be used to cycle between three modes: video
standby ( ), still image ( ), and review ( ). In video standby mode, there
shows ‘time’ & ‘1080FHD’ (white color font) at the top right of the display.
The ‘time’ means how many time the rest storage of the card would allow you to
record video. The ‘1080FHD’ means the video resolution is 1080FHD in this
mode.
To record videos
In the video standby( ), press the OK button briefly to begin recording. The
elapsed time(red color font) in the recording will appear at the top right. To
stop recording, short press the OK button again. The OK button on the remote
has the same function.
To Capture pictures
There are two ways to capture pictures.
- In the recording video mode ( ), press the Picture Capture button(Marked with a camera) briefly to capture an image.
- In the still image mode ( ), press ‘OK’ button to capture an image. The picture capture button and ‘OK’ button on the remote has the same function.
Note: You can’t take pictures or videos in review mode
Reviewing and Managing Images
To review and manage images on the display, short press the ‘M’ button to
select review mode. Use the Up and Down buttons to cycle through the pictures
and videos.
To play a video, short press the OK button to start play. Press the OK button
again to pause. Press ‘M’ button to stop playing the current video.
Hit the ‘M’ button again to exit review mode.
While reviewing a still image or video, the Menu button can be used to provide
additional options. Press the Menu button and hold for a while till options
show up.
Delete
- Delete Current: deleting just the current image/video;
- Delete All : deleting all unprotected images and videos;
Protect
Lock Current/All: provides protection for the current/all image/video
from deleting accidentally, but not from Format function;
Unlock Current/All: unlock the current/all image/video.
Settings
In each mode, press the M button and hold it for a while until the Video/Still
image/Review Menu shows up on the display(Or you can press MENU button on the
remote). Short press M button again, get into the general Setup Menu.
For example, if you are in Video standby mode, and you long press MENU, this
is the first menu would show, the “Video menu”:
Then, press MENU button (or M on the monitor) again, you get into the Setup menu, like this:
Date/Time
Press “OK” into Date/time setting. Use “Up” and “Down” to select the correct
number for year/month/day. Once you finish setting a number, press “OK” on the
monitor to the next number. Or, you can use “Left” and “Right” on the remote
to get to the one that you want.
Press “MENU” button on the remote to exit date/time setting directly. If you
don’t have the remote, you have to go through all over these settings one by
one and then press OK again to exit.
To save settings
After you set everything right, you should turn off the device by pressing
ON/OFF button on the monitor and hold it until the device switching off.
If you turn off the device by cutting off the power supply, the setting would
not be saved.