meskey Foldable 3 in 1 Wireless Charging Station Instruction Manual
- October 30, 2023
- meskey
Table of Contents
meskey Foldable 3 in 1 Wireless Charging Station
Product appearance
Instructions for use
- Please connect this wireless charger to the 5V3A, 9V/3A adapter through the Type-c fast charging cable and connect the source
- Put the phone in the mobile phone charging area and the mobile phone can be charged
- Place the watch in the watch charging area to charge the watch
- Put the wireless charging Bluetooth earphone box in the earphone charging area to charge the earphone
LED status
| Mode | TWS indicator | Phone indicator |
|---|---|---|
| Power | Bright blue light | Bright blue light |
| Standby | The blue light is |
always on
| The blue light is
always on
TWS charging| Blue light to green light|
Phone charging| | Blue light to green light
FOD| The blue light flashes quickly, remove the foreign object and stop
flashing| The blue light flashes quickly, remove the foreign object and stop
flashing
Notice!
In order to ensure the safe and efficient charging of the three devices at
Instruction manual X1 the same time, it is recommended to use adapters and
fast charging cables above 9V/2A or 9V/3A. (If the adapter is lower than
5V/2A, this charger will have a problem of stopping charging)
Foldable Operating Instructions
Foldable design
the watch charge can be detached for separate use
Watch charger storage
The watch wireless charger can be stored in the bottom groove when not in use
Product parameters
-
Name
Foldable 3 in 1 Wireless Charging Station -
Product size
144mm121mm25mm -
Operating frequency
110-205KHz -
Material
ABS+PC -
Wireless charging effective distance
≤5mm -
Input
9V/3A(Max) 5V/3A(Max) -
Output (phone)
5W/7.5W/10W/15W(Max) -
Output (TWS)
5W(Max) -
Output (Galaxy Watch)
3W(Max)
Applicable equipment
Please check whether the mobile phone supports wireless charging. This product
supports fast wireless charging function and conforms to QI wireless charging
standards; By magnetic induction Enables short-range wireless power transfer
Adapter selection
When using a 5V/2A output adapter, the wireless charger supports a5W load.
When using QC3.0 compliant adapters, the wireless charger supports 15W load;
*In order to ensure the normal use of the charger, it is recommended to use PD
fast charging or QC3.0 compliant adapter
Warn!
Do not put metal debris or magnetic cards on the charging pad, it may cause
the charger to heat up! Foreign objects should be removed when alarming!
Slight heating is normal, and it will heat up during the charging of the
mobile phone battery! Do not place the charger near fire sources or corrosive
environments
Packing list
- Wireless charger X1
- USB cable X1
- Instruction manual X1
Federal Communications Commission Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.