CURT 11475 Class I 1.25-Inch Trailer Hitch Receiver Instruction Manual
- June 4, 2024
- Curt
Table of Contents
CURT 11475 Class I 1.25-Inch Trailer Hitch Receiver
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER’S RECOMMENDED TOWING
CAPACITY
For more information log onto www.curtmfg.com & for
helpful towing tips log onto www.hitchinfo.com
WEIGHT CARRYING:
- TRAILER WEIGHT: LBS.
- TONGUE WEIGHT: LBS.
INSTALLATION TIPS:
- BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY.
- TO EASE INSTALLATION, 2 PEOPLE MAY BE REQUIRED.
- USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED.
- NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT 877.287.8634
INSTALLATION REQUIRES:
LEVEL OF DIFFICULTY: EASY
VEHICLE PHOTO:
HITCH ILLUSTRATION:
INSTALLATION WALKTHROUGH:
ITEM : QTY PART : NUMBER : DESCRIPTION
- 4 1/2 – 13 x 2″, GR8 CARRIAGE BOLT, GR8
- 4 CM-SP10 .250 x 1.00 x 2.50″ SQUARE HOLE SPACER
- 4 HFN 1213, GR8 HEX FLANGE NUT
- 4 1_2 FISHWIRE 1/2″ FISHWIRE
-
Lower exhaust by removing M8 bolts from the (2) rear exhaust hangers using a 13mm socket. Save for reinstallation.
NOTE: Removal of additional exhaust hanger may ease installation.
-
Use a die grinder to enlarge access slot on each side to 1.125″ holes. Fishwire 1/2″ carriage bolts and SP10 spacers through access holes in driver and passenger side frame rails and into position as shown below.
-
Reverse fishwire 1/2″ carriage bolts and SP10 spacers into position as shown below. Leave fishwires attached. NOTE: Disconnecting active exhaust connector may ease installation.
-
Raise hitch into position, remove fishwires, and loosely secure hitch with 1/2″ flange nuts.
-
Torque all 1/2″ hardware to 110 ft-lbs.
-
Raise exhaust following steps 1-3 in reverse order.
VOLKSWAGEN GOLF R
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER
WEIGHT & LBS. TONGUE WEIGHT.
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED
BY 18050 STABILIZING STRAPS.
WARNING: FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID
PRODUCT WARRANTY
WARNING: DO NOT EXCEED VEHICLE MANUFACTURER’S RECOMMENDED TOWING
CAPACITY
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT
1-877-287-8634
ITEM : QTY : PART NUMBER : DESCRIPTION
- 4 1/2 – 13 x 2″, GR8 CARRIAGE BOLT, GR8
- 4 CM-SP10 .250 x 1.00 x 2.50″ SQUARE HOLE SPACER
- 4 HFN 1213, GR8 HEX FLANGE NUT
- 4 1_2 FISHWIRE 1/2″ FISHWIRE
TOOLS REQUIRED
- RATCHET
- 9″ EXTENSION
- 13mm SOCKET
- 3/4″ SOCKET
- TORQUE WRENCH
- DIE GRINDER
INSTALLATION STEPS
- Lower exhaust by removing M8 bolts from the (2) rear exhaust hangers. Save for reinstallation. Removal of additional exhaust hanger may ease installation.
- Use a die grinder to enlarge access slot on each side to 1.125″ holes. Fishwire 1/2″ carriage bolts and SP10 spacers through access holes in driver and passenger side frame rails and into position as shown above. Reverse fishwire 1/2″ carriage bolts and SP10 spacers into position as shown above.
- Reverse fishwire 1/2″ carriage bolts and SP10 spacers into position as shown below. Leave fishwires attached. Disconnecting active exhaust connector may ease installation.
- Raise hitch into position, remove fishwire, and loosely secure hitch with 1/2″ flange nuts.
- Torque all 1/2″ hardware to 110 ft-lbs.
- Raise exhaust following steps 1-3 in reverse order.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>