CURT 81830 Certified 17-32 Inch Safety Latch S-Hook Instruction Manual
- June 4, 2024
- Curt
Table of Contents
INSTALLATION INSTRUCTIONS
81830 Certified 17-32 Inch Safety Latch S-Hook
WARNING: DO NOT EXCEED PRODUCT RATING OR TOW VEHICLE LAMP LOAD RATING, WHICHEVER IS LOWER
NOTICE
All steps must be followed to ensure the towed-vehicle RV harness will
function properly. Once installed, test for proper function by connecting a
properly wired tow vehicle.
TOOLS NEEDED
Wire stripper
Wire crimper
Cutting tool
WARNING
The battery connection must be fuse-protected, 10-amp max. Exceeding the
product rating can cause loss of warranty, overheating, and potential fire. Do
not exceed product rating or tow vehicle lamp load rating, whichever is lower.
Signal Circuits – 3.0 amps per side
Tail / Running Circuits – 6.0 amps total
Check vehicle owner’s manual or contact the vehicle manufacturer for more
information.
INSTALLATION / SAFETY INSTRUCTIONS
Step 1
Locate the vehicle battery and disconnect the negative battery terminal. Be
sure to fasten this wire down and away from the battery while completing the
installation process.
Step 2
Locate the breakout on the RV harness labeled “For trailer use only: converter
required”.
Step 3
Identify the protective dust cover from the RV-harness add-on breakout (A).
Step 4
Press down on the female 4-way connector and pull outward to separate from the
RV-harness (B). Inspect the connectors for dirt and debris and clean if
necessary.
Step 5
Plug the mating connector on the converter harness into the RV-harness from
Step 3.
Step 6
Locate a suitable grounding point near the connector such as an existing screw
with the nut in the vehicle frame or drill a 3/32″ pilot hole for the provided
screw. If possible, use the existing hole drilled for the RV-harness ground
wire. The area should be free of rust, dirt, and paint. Secure the white
ground wire using the ring terminal and provided screw.
**WARNING: Check for miscellaneous items that may be hidden behind or
under any surface before drilling to avoid damage and/or personal injury.
Step 7
If the harness is mounted in the interior of a hatch or trunk, route the
4-flat through the hatch or trunk far enough away so the harness does not
pinch in the locking mechanism. When not in use roll up and place in the trunk
or hatch. If the harness is mounted on the exterior, route the 4-flat near the
vehicle hitch and secure to the vehicle or hitch. Secure any loose wire with
the provided cable ties
Step 8
Route the black power wire from the vehicle battery as shown on the provided
‘Powered Converter Lead Instruction Sheet’.
Step 9
With the 4-flat extension plugged into the RV harness on one end and the RV on
the other, perform a function test. These functions will only work on the
brake/taillight combination lamp. When not in use store the 4-flat extension
inside the vehicle. 4-flat harness color codes: White – Ground Green – Right
Turn / Brake Brown – Taillights Yellow – Left Turn / Brake
Step 10
Locate a suitable position to mount the converter box. Clean the surface prior
to mounting. Remove the paper from the back of the double-sided tape and press
it against the surface.
Step 11**
Secure any loose wires behind the taillights with the provided cable ties.
Reinstall all items removed during installation. Install the provided 4-flat
dust cover to help prevent corrosion.
POWERED CONVERTER LEAD INSTRUCTION SHEET
NOTICE
Illustrations are for reference only. Battery location may differ depending
on the vehicle.
WARNING
Route 12 GA wire to vehicle battery location, taking care to avoid any
pinch points and honor rotating components.
WARNING
To avoid personal injury or property damage, check for miscellaneous items
that may be behind or under any surface before drilling.
NOTICE
- This converter system is to be used only on 12 volt negative ground systems.
- Secure power wire to vehicle chassis using cable ties provided.
- When passing the power wire through sheet metal, use an existing grommet, add a grommet or use silicone to protect the power wire from sharp edges.
- Overall T-connector design may differ from the illustration. The illustration should be used for power lead instruction only. Illustration is not to scale.
Green – Right turn
Red – Brake
Yellow – Left turn
Brown – Taillight
58920-INS-RA
Documents / Resources
| CURT
81830 Certified 17-32 Inch Safety Latch
S-Hook
[pdf] Instruction Manual
81830 Certified 17-32 Inch Safety Latch S-Hook, 81830, Certified 17-32 Inch
Safety Latch S-Hook, Safety Latch S-Hook, Latch S-Hook, S-Hook, Hook
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>