FLASH P7100447 LED PAR 64 4x30W 4-In-1 COB White 4 Sections Mk2 User Manual

: June 4, 2024
: FLASH

Table of Contents

INTRODUCTION
SAFETY INFORMATION
PRODUCT INFORMATION
INSTALLATION
CONNECTIONS
OPERATION MANUAL
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PROFESSIONAL

FLASH P7100447 LED PAR 64 4x30W 4 In 1 COB White 4 Sections
Mk2

LED PAR 64 4x30W 4in1 COB White
4 SECTIONS Mk2
P7100447
USER MANUAL

INTRODUCTION

Thank you for purchasing LED PAR 64 4x30W 4in1 COB White 4 Section Mk2. For safety reasons and to ensure the trouble-free operation, and carefully read the instructions.

SAFETY INFORMATION

Installation should be done by qualified personnel in order to minimize the risk of accidental electric shock
Disconnect the power supply before installation.
Before connecting the unit to the mains, make sure it is not damaged mechanically. If you notice any signs of damage you should contact your dealer immediately. Do not connect the device to the mains.
Do not use the device in high humidity conditions and at temperatures above 40° C
The device must be installed on stable structures
Always use a steel security cable to attach the device to a stable structure
Do not connect the power supply to more than 9 devices in series.

PRODUCT INFORMATION

3.1 Features

4 sections are controlled separately by DMX
16-bit dimming resolution
Various dimming curves for smooth dimming in 8-bit mode
Dim delay (light bulb simulation)
Full DMX signal regeneration
Electronic protection against overheating
THEATRE or DISCO cooling volume modes.
Permanent color correction
Native support for optional wireless DMX module

3.2 Specification

Power consumption: 120W
Power supply voltage: 100 – 245V
Voltage frequency: 50/60Hz
Diode type: 4in1
Number of diodes: 1
Diode power: 30W
Display: Color LCD
Color: W2000K, W3100K, W4200K, W9500K
Beam angle: 80°
Dimming: Linear: 0 – 100%
Flash frequency (min): 1Hz
Flash frequency (max): 20Hz
DMX standard: DMX 512
Control interface: 4 buttons
Operating modes: DMX512, Auto, Sound-controlled, Master / Slave
Features: 16-bit dimming, various dimming curves, bulb simulation, DMX Signal regeneration, Electronic protection against overheating
AC IN: powerCON
AC OUT: powerCON
DMX IN: XLR – 3 pin
DMX OUT: XLR – 3 pin
IP Rating: IP20
Housing made: ABS
Cooling: Active
Height [cm]: 30
Width [cm]: 27
Depth [cm]: 12,5
Weight [kg]: 2,8
Weight with packaging [kg]: 4,7

INSTALLATION

After removing the packaging, check if the device was not damaged during transport. Before connecting to the mains, make sure that the device is securely mounted. The manufacturer is not responsible for damage caused by unstable mounting.
CAUTION! Always use steel security cable to attach the device to a stable structure. Ensure proper connection to the mains and proper grounding. Make sure that the electrical parameters are consistent with device requirements. All activities, including connecting the device to the mains must be performed by qualified personnel.

CONNECTIONS

The device is equipped with the following interfaces:

DMX (in/out): XLR 3-pin socket
Power (in/out): powerCON socket

5.1 Connecting DMX signal
The connection is performed using a cable with XLR-female -> XLR-Male plugs.

FLASH P7100447 LED PAR 64 4x30W 4 In 1 COB White 4 Sections Mk2 - fig
1

FLASH P7100447 LED PAR 64 4x30W 4 In 1 COB White 4 Sections Mk2 - fig
2

5.2 Voltage specification

Input Voltage	Total Power	Frequency
100~245V	120W	50/60Hz

5.3 Connecting power supply
The connection is performed using a power cable with a PowerCon connector (included). The device must be operated by qualified personnel. Make sure that the power grid supply parameters are consistent with device parameters and that limitations are not exceeded.
CAUTION! In the case of cable, damage does not attempt to repair it. Replacement or repair can be made only by the manufacturer or by a person with appropriate permissions.
Maximum number of devices connected in series: 9