DURASTAR DRPTACWS PTAC Foldable Wall Sleeve Instruction Manual

October 30, 2023
DURASTAR

DURASTAR logo SKU: DRPTACWS
Foldable PTAC Wall Sleeve

WALL SLEEVE ASSEMBLY INSTRUCTIONS

SLEEVE HARDWARE

ITEM DESCRIPTION QTY DIMENSIONS
1 BOTTOM COVER 1 41 7 ⁄8” x 14 3 ⁄4“
2 TOP COVER 1 41 7 ⁄8” x 14 3 ⁄4“
3 LEFT COVER 1 14 3 ⁄4“ x 15 7 ⁄8”
4 RIGHT COVER 1 14 3 ⁄4“ x 15 7 ⁄8”
5 SEAL A 1 26 3 ⁄8”
6 SEAL B 2 1 5 ⁄8”
7 LONG SCREW 4 #8 x 3 ⁄4“
8 SHORT SCREW 14 #8 x 3 ⁄8”

DURASTAR DRPTACWS PTAC Foldable Wall Sleeve

SLEEVE ASSEMBLY

  1.  Open the LEFT COVER and RIGHT COVER as shown below.
    DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - LEFT
COVER

  2. Install 6 short screws as shown below.

  3.  Attach the BOTTOM COVER to the LEFT COVER and RIGHT COVER using 8 short screws as shown below.
    DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - BOTTOM

  4. Turn the SLEEVE as shown below.

  5. Attach SEAL A and SEAL B to the SLEEVE in the locations shown below.DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - CONTINUED

UNIT INSTALLATION

These instructions are for reference only. See the Unit Manual for more detailed instructions.

  1. Lift unit level and slide unit into wall sleeve until firmly against front of wall sleeve and secure with 4 long screws through the unit flange holes.DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - UNIT

DRAIN KIT INSTALLATION INSTRUCTIONS

DRAIN KIT PARTS LIST

ITEM DESCRIPTION QTY
1 DRAIN OUTLET PLATE 1
2 FOAM GASKET WITH DRAIN OUTLET 6
3 COVER PLATE 2
4 BENT TUBE 1
5 STRAIGHT TUBE 1
6 SCREWS (#8 x ½”) 6

DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - DRAIN

HOW TO INSTALL THE DRAIN KIT
The Drain Kit can be installed for back-side drainage or bottom-side drainage. Follow the instructions for the desired drainage location.

Back-Side Drain Installation

  1. Attach a foam gasket to the drain outlet plate and  cover plate as shown below.DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - Cover Plate
  2. Insert the bent tube into the drain outlet plate and rotate the tube to the proper position as shown below.DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - bent tube
  3. Install the tube and drain outlet plate to the outlet located at the back of the sleeve with two screws and install the cover plate to the other outlet using two screws as shown below.
    NOTE: The drainage tube may be placed on either side of the sleeve. Before tightening the screws, make sure the tube’s position will allow the sleeve to fit through the wall.DURASTAR DRPTACWS PTAC Foldable Wall Sleeve -
Side Drain

Bottom-Side Drain Installation

  1.  Attach a foam gasket to the drain outlet plate and cover plates as shown below.DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - view \(51\)
  2. Insert the straight tube into the drain outlet plate as shown below.DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - tube\)
  3. Drill two 1/8” holes in a suitable position of the bottom of the wall sleeve to line up with the holes of the drain outlet plate. Then drill one 3/8” ~1/2” hole in the middle of the two holes as shown below.DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - middle
  4. Attach the tube and drain outlet plate to the bottom of the wall sleeve using two screws. Gently tighten the screws at the same time to avoid damaging the tube.DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - tube
  5. Install the two cover plates over the outlets on the back of the sleeve using four screws. Fasten tightly to avoid leaks.DURASTAR DRPTACWS PTAC Foldable Wall Sleeve - back

©2022 Durastar
V1.0 0822

Documents / Resources

| DURASTAR DRPTACWS PTAC Foldable Wall Sleeve [pdf] Instruction Manual
DRPTACWS PTAC Foldable Wall Sleeve, DRPTACWS, PTAC Foldable Wall Sleeve, Foldable Wall Sleeve, Wall Sleeve, Sleeve
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DURASTAR User Manuals

Related Manuals