Giant Bicycles Cadex Tri Frameset Bike User Manual

Bicycles Cadex Tri Frameset Bike
User Manual

FRAME SIZING

SIZING GUIDE AND GEOMETRY
Sizing to be used as a reference only. Please check with a local authorized dealer to determine the correct size.
Available sizes may vary from country to country.

| | XXS| XS| S| M| L
---|---|---|---|---|---|---
| HEIGHT (cm)| 150 – 162| 156 – 168| 164 – 176| 172 – 186| 180 – 195
| INSEAM (cm)| 62 – 76| 65 – 80| 70 – 85| 75 – 90| 80 – 98
A| SADDLE HEIGHT RANGE (mm)| 540-710| 580-750| 620-790| 660-830| 700-870
B| SEAT TUBE LENGTH (mm)| 440| 475| 510| 545| 580
C| SEAT TUBE ANGLE| 76 – 80°| 76 – 80°| 76 – 80°| 76 – 80°| 76 – 80°
D| TOP TUBE LENGTH (mm)| 475| 495| 520| 550| 580
E| HEAD TUBE LENGTH (mm)| 70| 95| 120| 145| 170
F| HEAD TUBE ANGLE| 71.0°| 73.0°| 73.0°| 73.0°| 73.0°
G| FORK RAKE (mm)| 40| 40| 40| 40| 40
H| TRAIL (mm)| 76.1| 63.3| 63.3| 63.3| 63.3
I| WHEELBASE (mm)| 968| 976| 1005| 1039| 1072
J| CHAIN STAY LENGTH (mm)| 405| 405| 405| 405| 405
K| BOTTOM BRACKET DROP (mm)| 80| 80| 77| 74| 74
L| ARMREST STACK (15D) (mm)| 545 – 615| 575 – 645| 595 – 665| 615 – 685| 640 – 710
M| ARMREST REACH (15D) (mm)| 340 – 430| 355 – 445| 375 – 465| 400 – 490| 425 – 515
| FRAME STACK (mm)| 483| 513| 534| 555| 579
| FRAME REACH (mm)| 390| 405| 426| 452| 478
N| HEIGHT (mm)| 530 – 570| 560 – 600| 580 – 620| 600 – 640| 625 – 665
O| HANDLEBAR WIDTH (mm)| 400| 400| 400| 400| 400
P| EXTENSION WIDTH (mm)| 110 | 190| 110 | 190| 110 | 190| 110 | 190| 110 | 190
Q| ARMREST WIDTH (mm)| 190 – 310| 190 – 310| 190 – 310| 190 – 310| 190 – 310
| COMPATIBLE SIZE (mm)| 700 x 28C| 700 x 28C| 700 x 28C| 700 x 28C| 700 x 28C

STACK AND REACH RANGE

FIT DATA CHART GEOMETRY

0°|
---|---
| | XXS| XS| S| M| L
L| ARMREST STACK-MIN (mm)| 560| 590| 610| 630| 655
L| ARMREST STACK-MAX (mm)| 640| 670| 690| 710| 735
M| ARMREST REACH-MIN (mm)| 340| 355| 375| 400| 425
M| ARMREST REACH-MAX (mm)| 430| 445| 465| 490| 515
5°|
| | XXS| XS| S| M| L
L| ARMREST STACK-MIN (mm)| 555| 585| 605| 625| 650
L| ARMREST STACK-MAX (mm)| 625| 655| 675| 695| 720
M| ARMREST REACH-MIN (mm)| 340| 355| 375| 400| 425
M| | 430| 445| 465| 490| 515
10°|
| | XXS| XS| S| M| L
L| ARMREST STACK-MIN (mm)| 550| 580| 600| 620| 645
L| ARMREST STACK-MAX (mm)| 630| 660| 680| 700| 725
M| ARMREST REACH-MIN (mm)| 340| 355| 375| 400| 425
M| ARMREST REACH-MAX (mm)| 430| 445| 465| 490| 515
15°|
L| ARMREST STACK-MIN (mm)| 545| 575| 595| 615| 640
L| ARMREST STACK-MAX (mm)| 615| 645| 665| 685| 710
M| ARMREST REACH-MIN (mm)| 340| 355| 375| 400| 425
M| ARMREST REACH-MAX (mm)| 430| 445| 465| 490| 515

TRI BAR REMOVAL & ASSEMBLY

REMOVAL

1. Install fork pads F-R and F-L onto the upper part of fork (A).
2. Loosen but don’t remove the four cockpit fixing bolts with a 4mm hex key (B).
3. Lift up the extension assembly and detach base bars from both sides. Install protective spacer to the four fixing bolts. (C).
4. Gently flip down both base bars without putting too much tension on the brake hoses. Gently lay each bar against the fork leg on the same side. (D).
5. Secure both base bars to the fork legs with the shorter Velcro straps. (E).
6. Secure spacers with Velcro straps. Completely loosen the four cockpit fixing bolts. (F).
7. Flip the assembly down and position it gently against the front of the fork. Secure the entire assembly with the longer Velcro straps. (G).

ASSEMBLY
NOTE:
Always use a torque wrench.
After assembly, with both wheels on the floor, hold both brakes and gently rock the bike forward and backward to make sure nothing is loose.

1. Remove securing Velcro strap from assembly (A).
2. Replace extension bar assembly and loosely refit the four fixing bolts. Remove Velcro straps (B).
3. Remove protective spacers. (C).
4. Replace base bars. Tighten all cockpit fixing bolts to 5.5Nm with a 4mm hex (D)
5. Remove protective pads (E).
6. Replace arm cups. Tighten bolts to 4Nm with a 3mm hex (F).

TOP TUBE STORAGE & TOOLKIT REMOVAL & INSTALLATION

NOTE:
Make sure all storage parts fit snugly to the frame and do not rattle.
TOP TUBE STORAGE REMOVAL

1. Hold the lower end firmly and push upwards (A).
2. Pivot the storage box upwards to remove. (B).

TOP TUBE STORAGE INSTALLATION

1. Insert and firmly push front latch into the frame recess (A).
2. Push storage box downward into the frame (B).

TOOLKIT REMOVAL

1. Hold the lower end firmly and push upwards (A).
2. Pivot the toolkit sideways to remove (B).

TOOLKIT INSTALLATION

1. Insert and firmly push upper latch into the frame recess (A).
2. Push tool box into the frame until it fits snugly. (B).

HYDRATION SYSTEM REMOVAL & INSTALLATION

REMOVAL

1. Remove front aero cover by pulling outward with both hands (A)
2. Take out the bladder and disconnect the straw. Replace the bladder (B).
3. Use your index finger to unclip the straw while pressing the clip with your thumb (C)
4. Remove the straw by gently pulling through from the front side of the bike (D).

INSTALLATION
NOTE:
Once the straw has been refitted, turn the handlebar from side to side to make sure is not compromised. If you feel any interference, remove the straw and refit again.

1. Feed the straw from the head tube trough the right-side of steerer (A).
2. Take out the bladder and reconnect the straw. Replace the bladder (B).
3. Adjust the straw to desired length and secure the straw onto the clip (C).
4. Refit the front aero cover (D).

SEAT POST & SADDLE ADJUSTMENT

CLAMP POSITION
Front position 78° to 80° seat tube angle Rear position 76° to 78° seat tube angle SADDLE CLAMP ADJUSTMENT

1. Remove saddle (A).
2. Loosen and remove both clamp fixing bolts 1 (B).
3. Pull out clamp 2 , turn it 180° horizontally and refit it into seat post (C).
4. Replace clamp fixing bolts 1, tighten to 5Nm (D).

SEAT POST
Minimum insertion – 80mm. NOTE:

1. Always use a torque wrench
2. Once the installation or adjustment has been completed, grab the saddle and rock it back and forth to ensure all fasteners are snug.

SADDLE POSITION ADJUSTMENT

1. Loosen the side bolt 1 a full turn; Loosen the top bolt 2 a full turn (A)
2. Adjust saddle angle, fore or aft to preferred position (B).
3. Tighten the top bolt to 5 Nm with 4 mm hex; Tighten the side bolt to 5 Nm with 4 mm hex (C)
4. Double check clamp fixing bolts ➌ (D)

SADDLE REMOVAL & INSTALLATION

1. Loosen and remove the side bolt 1 (A).
2. Loosen and remove the top bolt 2 and the upper piece (B).
3. Remove the saddle from the clamp. Rock the saddle back and forth to help removal. (C).
4. Select 7mm top clamp for alloy rail saddle or 9mm top clamp for carbon rail saddle. ➍ (D)
5. Apply carbon paste to the clamp housing (E).
6. Replace top clamp ➍ and loosely tighten the top bolt 2 and upper piece (F).
7. Refit saddle with the lower piece and lightly tighten the side bolt 2 (G)
8. Adjust saddle angle, fore and aft to preferred position (H).
9. Tighten the top bolt and the side bolt to 5 Nm (I)
10. Double check clamp fixing bolts ➌ (J)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>