STIGA 95C E QF Series Cutting Machine Instruction Manual

85C QF Series
95C E QF Series
Cutting means assembly
OPERATOR’S MANUAL Translation of the original instruction

WARNING: read thoroughly the instruction booklet before using the machine.

95C E QF Series Cutting Machine

|
---|---
|

[1]| TECHNICAL DATA| Type| 85C QF| 95C E QF
---|---|---|---|---
[2]| Overall dimensions| fig. 2| |
[3]| A= Length| mm| 892| 920
[4]| B= Height| mm| 345| 345
[5]| C= Width| mm| 991| 1023
[6]| Weight| kg| 45| 49
[7]| Min. cutting height| mm| 25| 25
[8]| Max. cutting height| mm| 85| 85
[9]| Cutting width| cm| 85| 95
[10]| Cutting height manual adjustment| | ✓| –
[11]| Cutting height electric adjustment| | –| ✓
[12]| Compatible machines (Type)| | |
| V 302| | ✓| –
| V 302 S| | –| ✓
| V 302 Li 48| | –| ✓
[13]| Spare cutting-means assy codes| Fig:Pos| |
| | 16:A| 1134-7881-01| 1134-7881-02
| | 16:B| 1134-7880-01| 1134-7880-01

WARNING!: READ THOROUGHLY THE INSTRUCTION BOOKLET
BEFORE USING THE MACHINE. Keep for future reference.

GENERAL

1.1 HOW TO READ THIS MANUAL
In this manual, certain paragraphs containing particularly important information for operator safety and machine operation are highlighted in different ways according to the following criteria.
NOTE or IMPORTANT indicates clarifications or other elements concerning the information provided for the purpose of avoiding damage to the machine or causing any harm.
The symbol highlights a hazard.. Failure to observe the warning may lead to personal injury or injury to others and/or material damage.
The paragraphs highlighted in a box with a dotted grey edge indicate optional features which may not be present on all the models covered by this manual. Check if your model as the feature in question.
All the indications “front”, “back”, “left” and “right” refer to the position of the operator when driving the machine.

1.2 REFERENCES
1.2.1 Figures
The figures in this User Manual are numbered 1, 2, 3 and so on. Components shown in the figuresare marked A, B, C, etc. A reference to component C in figure 2 iswritten as: “See fig. 2.C” or simply “(Fig. 2.C)”.All figures are indicative. Parts on your machine may vary from those shown.
1.2.2 Titles
This manual is divided into chapters and paragraphs. The title of the paragraph “2.1 Training” is a subheading in chapter 2 “Safety regulations”. References to titles or paragraphs are indicated with the abbreviation “chap.” or “par.” accompanied by the relative number. Example: “chap. 2” or “par. 2.1”.

SAFETY REGULATIONS

2.1 TRAINING
Before using this equipment, carefully read the instruction manual for the machine on which it is to be installed.
This Safety Regulations chapter refers only to the interchangeable equipment. For the Safety Regulations concerning a rideon lawnmower with front cutting, please refer to the specific instruction manual.
Be familiar with the controls and the proper use of the machine. Learn how to stop the machine quickly. Failure to observe the warnings and instructions may lead to fire and/or serious injury.

• Never allow children or people unfamiliar with these instructions to use the machine. Local regulations may restrict the age of the operator.
• Never use the machine if the user is tired or unwell, or has taken medicine, drugs, alcohol or substances which may slow hireflexes and compromise his judgement.
• Never transport children or other passeng
• Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their propertIt is the user’s responsibility to assess the potential risk of the area where work is to be carried  ut, and to take all the necessa precautions to ensure his own safety and that of others, particularly on slopes or rough, slippery and unstable ground.
• In the event of changes in ownership or loan of the machine, make sure the future user reads the instructions for use provided in this manual.

2.2 PRELIMINARY OPERATIONS
Personal Protective Equipment (PPE)

• Wear suitable work clothing, sturdy, slip-resistant footwear and long trousers. Never activate the machine when barefoot or wearing open-toe sandals. Wear hearing defenders.
• DO NOT wear scarves, smocks, necklacesbracelets, loose clothing with long flaps or laces, ties or any other dangling or loose accessory which could get caught up in machine parts or in objects/ materials present in the operating area.
• Suitably tie back long hair.

Working area / Machine

• Thoroughly inspect the operating area and remove any objects which could be thrown into the air by the machine or damage its cutting means/rotary components (stones, sticks, metal wire, bones, etc.)

2.3 DURING OPERATION

Working area

• Do not use the machine in potentially explosive environments, in the presence of flammable liquids, gases or dust. Electrical contacts or mechanical rubbing may generate sparks which could ignite flammable dust or fumes.
• Mow only in daylight or with good artificial light in good visibility conditions.
•  Keep persons, children and animals away from the working area. Any children near the area must be supervised by another adult.
• Avoid working in wet grass, in the rain or when there is a risk of thunderstorms, particularly if lightning is forecast.
•  Take special care in the presence of irregularities in the terrain (bumps, dips), slopes, hidden dangers and any obstacles which could obscure your vision.
•  exercise caution in the proximity of cliffs, ditches or embankments. The machine may overturn if a wheel drives over the edge or the edge gives way.
•  Take care when operating on slopes where maximum attention must be exercised to avoid any risk of roll-over or losing control of the machine. The main cause behind a loss of machine control are:
  • insufficient wheel grip
  • being driven too fast
  • inadequate braking
  • the type of machine is unsuitable for its task
  • lack of awareness of the effof ground conditions
  • Incorrect use of the machinas a towing vehicle

Conducyt

• Always keep hands and feet well away from the cutting device during both start-up and machine use.
• Warning: the cutting element continues to rotate for a few seconds after it has been disengaged or after the engine has been switched off.
• Take care with multiple blade cutting decks as one rotating blade may cause other blades to rotate.
• Disengage the cutting device or power take off and take the cutting device to its highest position:
  • During transfer from one operating area to another.
  • When crossing grass-free terrain.
• In the event of failures or accidents when working with the machine, stop the engine immediately and move the machine away to avoid causing further damage; in the event of accidents with injuries to operators or third parties, take the first aid measures which are most appropriate to deal with the situation and contact a health care facility for the necessary treatment. Carefully remove any debris which could cause damage or injury to persons or animals if ignored.

Limits of use

• Never use the machine if the safeguards are damaged, missing or incorrectly installed.
• Do not attempt to defeat, deactivate, remove or tamper with the installed safety systems/microswitches.

2.4 MAINTENANCE, STORAGE AND TRANSPORT
Regular maintenance and correct storage is essential for machine safety and optimum performance.
Never use the machine with worn or damaged parts. Faulty or worn-out parts must always be replaced and never repaired. Only use original spare parts: The use or non-original and/or incorrectly fitted parts will compromise the safety of the machine, may cause accidents or personal injuries for which the Manufacturer is under no circumstance liable or responsible.
Maintenance

• Be careful during adjustment of the machine, to prevent entrapment of the fingers between moving parts of the cutting means and fixed parts of the machine.

Storage

• To reduce the risk of fire, never leave containers holding waster materials inside buildings.

Handling and transport

• If the machine is transported on a truck or trailer, use ramps with suitable resistance, width and length.
• When transporting the machine with a vehicle it is necessary to:
  • get an adequate number of people to load the machine with the engine switched off;
  • position the machine where it does not constitute any kind of hazard to anyone;
  • secure it firmly to the means of transport using cables or chains to stop it from turning over and getting damaged.

2.5 ENVIRONMENTAL PROTECTION
Safeguarding the environment must be a relevant and priority aspect of machine use, of benefit to the community and the environment we live in.

• Avoid being a disturbance to the neighbourhood. Only use the machine at reasonable times of day (i.e. avoid using it very early in the morning or late in the evening when it may cause a disturbance to others).
• Adhere strictly to the local regulations governing the disposal of packaging, oil, fuel, filters, damaged parts or any other element which may have an impact on the environment; this waste should not be disposed of along with standard household waste, but must be disposed of separately and sent to special waste disposal facilities for handling and recycling.
• When the machine is withdrawn from service, do not dump it in the environment, but take it to a waste disposal facility in accordance with the local regulations in force.

MACHINE INFORMATION

3.1 DESCRIPTION OF THE MACHINE AND ITS INTENDED USE
The machine described herein is an interchangeable piece of equipment known as a cutting means assembly. It is an interchangeable gardening tool designed to be connected to another machine (a ride-on lawnmower with front cutting) from which it receoves drive and support.
3.1.1 Foreseen use
The machine “cutting-means assembly” has been specifically designed and built to mow grass.
In general this machine can:

• Cut and shred grass and deposit it on the ground (“mulching” effect).
• Cut grass and discharge it on the ground from the read.

3.1.2 Improper use
Any other use, different to the uses cited above, may be dangerous and cause injury and/or material damage. Improper uses (by way of example and not limited to) are:

• carrying people, children or animals on the machine;
•  pushing loads;
• activation of the cutting devices on grass-free areas.

Improper use will render the warranty null and void and the Manufacturer shall be exonerated from all liability, with all responsibility for damages or injuries to self or third parties being transferred to the user.
3.1.3 User types
This machine is designed for use by the general public, i.e. non-professional operators. It is intended for “hobby use”.
IMPORTANT The machine must be used by one operator.
3.2 WARNING SIGNS
There are various symbols on the machine (fig. 3). They are designed to remind the operator of the precautions which need to be taken to safely use the machine. What the symbols mean:

| CAUTION!!! Read the instruction manual before using the machine.
---|---
| CAUTION!!! Watch out for any loose objects on the ground. Pay attention to any other people who may be in the area.
| WARNING! Before performing any repair operations, disconnect the spark plug lead from the spark plug.
| CAUTION!!! Never put your hands or feet under the safeguard when the machine is in operation.

IMPORTANT Any damaged or illegible decals must be replaced. Order replacement decals from an authorised assistance centre.
3.3 IDENTIFICATION LABEL
The identification label holds the following data (fig. 1):

1. Trade mark
2. Manufacturer’s address
3. Model
4. Type of machine
5. Definition of the accessory
6. Weight in Kg
7. Year of manufacture
8. Serial number
9. Article code
10. CE conformity marking

Transcribe the machine identification data in the space provided on the label found in the back cover.
IMPORTANT Use the identification data written on the product identification label whenever you contact an authorized service centre.
IMPORTANT The example of the declaration of conformity can be found on the last pages of this manual.
3.4 MAIN COMPONENTS
The machine is made up of the following main components (fig. 1):
A. Arms
B. Safeguard
C. Wheels
D. Grip point for manual lifting
E. “Quick Flip” knob
F. Cutting means drive belt
G. Cutting height indicator
H. Manual cutting height adjustment (if present)
I. Electric cable connector (if present)
J. Cutting means
Components instalaled on the rideon lawnmower with front cutting
K. Quick-release supports
L. Lifting pulley
M. Accessory lift pedal
N. Cutting height electric adjustment switch
O. Power socket (if present)

INSTALLATION

IMPORTANT The safety regulations to be followed are described in chap. 2. Adhere strictly to the indications provided to avoid serious risks and/or hazards.
For storage and transport purposes, certain machine components are not installed in the factory but must be assembled when the machine is removed from the packaging. To so so, proceed as follows:
Unpacking and completing the assembly should be done on a flat and stable surface, with enough space for machine handling and its packaging, always making use of suitable equipment. Do not use the machine until all the indications provided in the “ASSEMBLY” section have been carried out.
4.1 ASSEMBLY COMPONENTS
The packaging holds the components needed for assembly (fig. 4) as listed in the table below:

4.1.1 Unpacking

1. Open the packaging carefully, taking care not to lose any parts.
2. Consult the documentation found in the box, e.g. including this User Manual.
3. Remove all unassembled parts from the box.
4. Remove the machine from the box.
5. Dispose of the box and all packaging materials in compliance with local legislation.

4.2 ASSEMBLY OF THE CUTTING MEANS DEVICE

1. Position the arm with the “Quick Flip” knob (fig. 5.C) on the side indicated in the figure and fasten it inside the bracket (fig. 5.H) with the screw (fig. 5.A).
2. Position the second arm (fig. 5.B) on the opposite side and secure in place with the screw (fig. 5.A).
3. Fit the second arm (fig. 5.B) to the opposite side and fasten it inside the bracket (fig. 5.H) with the screw (fig. 5.A)
4. Position the hook-up brackets (supplied with the ride-on lawnmower with front cutting) in the seats on the cross beam (fig. 5.G) and fasten the screws and nuts (supplied with the ride-on lawnmower with front cutting).

4.3 HOOKING UP THE CUTTING MEANS ASSEMBLY TO THE RIDE-ON LAWNMOWER.
The cutting-means assembly must be hooked up to the the ride-on lawnmower by means of the mounts attached to the front wheels and the lifting pulley (supplied with the ride-on lawnmower with front cutting) and the cutting-means drive belt (pre-installed on the cutting-means assy). For correct installation, follow the steps below in the indicated sequence, starting with the maximum cutting height adjustment, in order to ease the subsequent assembling phases.
4.3.1 Connection of the electric cable connector
If the cutting-means assembly have electrical cutting height adjustment, connect the cable to the socket (fig. 8.A).
4.3.2 Cutting height adjustment
In order to ease the assembling phases, adjust the maximum cutting height (par. 5.1).
4.3.3 Hook-up to the quick-release supports attached to the wheels
IMPORTANT For the following operations, see the relative instructions provided in the machine’s manual and on the manual accompanying the support.

1. Check that the quick-release supports are installed on the ride-on lawnmower and that the hook-up brackets are fastened in the seats on the cross beam of the cutting means assembly.
2. Position the cutting means assembly to the front of the ride-on lawnmower.
3. Turn the quick-release supports to the open position (fig. 6.A)
4. Lift the bottom part (fig. 6.B) of the hook-up staff and rest it on the peg (fig. 6.C) on both sides of the machine.
5. Couple the hook-up bracket (fig. 7.A) to the pin (fig. 7.B) on both sides.

4.3.4 Hook-up of the cutting means drive belt

1. Adjust the minimum cutting height (par. 5.1).
2. Stand in front of the ride-on lawnmower.
3. Pass the belt over the pulley (fig. 9.A) on the ride-on lawn mower.
4. Pull the tensioner (fig. 9.B) towards the front of the machine.
5. Pass the belt over the pulley (fig. 9.C) of the tensioner while gently releasing the tension and your grip.
6. With your foot, turn the quick-release supports to the closure position (fig. 7.C) and insert the peg or cotter pin (fig. 7.D).

4.3.5 Installation of the belt guard

1. Adjust the minimum cutting height (par. 5.1).

2. Insert the guard (fig. 10.A) on the left side (as seen from the front of the machine).

3. Insert the forks (fig. 10.B) on the wheel axle (fig. 10.C).
   Make sure that the safety guards is correctly installed as shown in (fig. 10).

4. Screw in and tighten the screws (fig. 10.D).

4.3.6 Lifting pulley assembly
This component is supplied with the rideon lawnmower with front cutting.

1. Set the maximum cutting height (par. 5.1).
2. Thread the cable (fig. 11.A) of the rideon lawnmower with front cutting into the lifting pulley guide (fig. 11.B).
3. After having assembled the cutting means assembly on the ride-on lawnmower with front cutting, position the lifting pulley (fig. 11.C) in the groove on the cross beam (fig. 11.D). Secure in place by turning the relative knob.

4.4 UNOOKING THE CUTTING MEANS ASS EMBLY FROM THE RIDE-ON LAWNMOWER.

For correct disassembly, follow the steps below in the indicated sequence.

1. If the cutting-means assembly has electric cutting height adjustment, disconnect the cable from the machine (fig. 8.B).

2.  Unscrew and extract the lifting pulley from the cross beam on the cutting means assembly.

3.  Remove the belt guard as follows: – Slacken and remove the screws (fig. 10.D).
   – Remove the guard (fig. 10.A)

4. Remove the pin or cotter pin (fig. 7.D) and turn the quick-release supports to the open position (fig. 6.A).

5. Slacken the drive belt as follows:
   – With your right hand take hold of the tensioner lever (fig. 9.B) and pull it towards the machine front side.
   – With your left hand remove the belt from the pulley (fig. 9.C).
   – Remove the belt from the pulley (fig. 9.A) on the machine.

6. Lift the quick-release supports hookup brackets (fig. 7.A) and detach the cutting means assembly from the rideon lawnmower with front cutting.

CONTROL COMMANDS

5.1 CUTTING HEIGHT ADJUSTMENT
Make adjustments with the cutting means stopped.
5.1.1 Cutting height electric adjustment
The cutting height is fully adjustable with minute precision by acting on the electric cutting height adjustment switch found on ride-on lawnmower with front cutting. The cutting height indicato (fig. 1.G) shows the height it is adjusted to.
IMPORTANT To activate electric adjustment it is necessary to connect the electric cable connector on the cutting means assembly to the socket (fig. 8.A) on the ride-on lawnmower with front cutting.
5.1.2 Manual cutting height adjustment
The cutting height can be adjusted to a number of pr-defined positions using the lever (fig. 12.A). The cutting height indicator (fig. 12.B) shows the height it is adjusted to.
5.2 “QUICK FLIP” KNOB
The “Quick Flip” knob makes it possible to take the machine from the transport position to themaintenance position quickly and easily, without having to dismantle any machine parts. (fig. 1.E).

USING THE MACHINE

IMPORTANT The safety regulations to be followed are described in chap. 2. Adhere strictly to the indications provided to avoid serious risks and/or hazards.
6.1 PRELIMINARY OPERATIONS
Grass can be cut in two ways.

• Cut and shred grass and deposit it on the ground (“mulching” effect).
• Cut grass and discharge it on the ground from the read.

When the machine is delivered the cuttingmeans assemb y is set for mulching.

Expulsion of grass from the back of the cutting-means assembly.

• Slacken and remove the screw (fig. 13.A) which secures the deflector in place (fig. 13.B).
• Remove the deflector (fig. 13.B).
• Keep the screw and the deflector in a safe place for future use.

6.2 SAFETY CHECKS
Perform the following safety checks and make sure the results match those provided in the tables.
Always carry out the safety checks before use.
6.2.1 General check

No mechanical damage.
Screws on the accessory and on the cutting means| Securely fastened (not loose)
Belt protection guard| Correctly positioned
Test drive with cutting means engaged (see the relative instructions provided on the machine’s instruction manual)| No abnormal vibrations.
No abnormal noise.

6.2.2 Machine
For the following operations, see the relative instructions provided in the ride-on lawnmower with front cutting’s manual.
6.3 START-UP / OPERATION
For the following operations, see the relative instructions provided in the ride-on  lawnmower with front cutting’s manual.
6.4 AFTER USE

• Perform cleaning (par. 7.4).
• Check for any damage. If necessary, contact an authorised assistance centre.

 ROUTINE MAINTENANCE

7.1 GENERAL INFORMATION
IMPORTANT The safety regulations to be followed are described in chap. 2. Adhere strictly to the indications provided to avoid serious risks and/or hazards.
All service and all maintenance checks must be carried out on a stationary machine with the engine switched off. Before cleaning or doing maintenance work, take out the ignition key and read the relevant instructions.
Wear suitable work wear, gloves and safety glasses before proceeding with maintenance operations.

• The frequencies and types of intervention are all indicated in the “Maintenance Tables”. The table is designed to help you keep your machine in efficient and safe working order. It indicates the main operations to be performed and the frequency of the same. Perform the relative operation described based on the first deadline to arrive.
• The use of non-genuine spare parts and accessories could adversely affect machine operation and safety. The manufacturer shall decline all liability in the event of injuries or damages caused by such parts.
• Genuine spare parts are supplied by authorized assistance workshops and dealers.

IMPORTANT Any maintenance and adjustment operations not described in this manual must be carried out by your Dealer or specialized service centre.
7.2 WASHING AND MAINTENANCE POSITION
It is strictly prohibited to take the cutting means assembly to the maintenance position without having first activated the equipment lift pedal (fig. 14.A).

1. Always put the parking brake on to make sure the machine does not move (see also the instructions provided in the ride-on lawnmower with front cutting’s manual).
2. If the cutting-means assembly has electric cutting height adjustment, disconnect the cable from the machine (fig. 8.A).
3. Activate the equipment lift pedal on the ride-on lawnmower with front cutting (fig. 14.A) and take the equipment to the transport position (see also the instructions provided in the ride-on lawnmower with front cutting’s instruction manual).
4. Pull the “Quick Flip” knob outwards (fig. 14.B) using your right hand so that the cutting means assembly can be lifted.
5. With your left hand take hold of the cutting means assembly (fig. 14.C) and lift slightly. Release the “Quick Flip” knob.
6. Slowly lift until the maximum height has been reached (you will hear a “click”) (fig. 15.A). The cutting means assembly remains locked in the maintenance position (fig. 15.B) “SERVICE POSITION”.
7. Perform maintenance on the cutting means. The machine is fitted with a safety system which prevents the engagements of the cutting-means assy when in maintenance or transport position. It is strictly prohibited to try to engage the cutting means when the cutting means assembly is in the maintenance position.
8. To return the cutting means assembly to the transport position, pull the “Quick Flip” knob out again and gently lower the cutting means manually. Once in the lowest position, push the “Quick Flip” knob fully inwards.
9. Put the equipment lift pedal to the operating position (see the instructions provided in the machine’s manual).
10. After cleaning using water, start the machine and any cutting decks to remove any water which may otherwise end up in the bearings and cause damage.

7.3 FASTENERS

• Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.
• At frequent intervals check all fasteners on the discharge chute to ensure they are securely tightened.

7.4 CLEANING

• Set the cutting-means assembly to the washing position.

• Clean the bottom of the cuttingmeans assembly with great care using only water and a brush.
  IMPORTANT Never use high-pressure water jets. It could damage the electrical components.

• If during use any of the paintwork has got scratched or come off, touch up when the surfaces are completely clean and dry.

• Use non-perishable yellow paint for outdoor applications which is suitable for metal.

UNSCHEDULED MAINTENANCE

8.1 CHECKING AND REPLACING THE CUTTING DEVICE
NOTE A poorly sharpened cutting device rips the grass causing the lawn to turn yello.
All operations concerning the cutting deck assy (disassembling, sharpening, balancing, assembling and/or replacement) are tough works and require a specific knowledge as well as special tools; for sake of safety, they should always be performed by an authorized service centre.
Always replace the entire cutting means assembly when damaged, crooked or warn, along with the screws. This is to ensure balance.
IMPORTANT It is advisable to replace cutting devices in pairs, especially in the event of marked differences in wear.
IMPORTANT Always use genuine cutting devices bearing the code indicated in the “Technical Data” table.
Due to product evolution, the cutting devices cited in the “Technical Data” may be replaced by others, with similar features of interchangeability and safe operation.
8.2 CHECKING AND REPLACING THE CUTTING MEANS DRIVE BELT
Check that the belt is intact without wear marks. If the belt is damaged or worn, replace it. If replacement is necessary, contact an authorised assistance centre.

STORAGE

When you intend to put your machine away for more than 30 days, proceed as follows:

1. Clean the accessory thoroughly.

2. Check that the accessory is not damaged.
   If necessary, see to the necessary repairs.

3. If the paintwork is damaged, touch it up to prevent rust.

4. Protect any exposed metal surfaces from rust.

5. Store the accessory indoors if possible.

6. It is suggested to store the machine by setting the cutting-means assy in working or transport position, so as to avoid damage to the drive belt (see also the instructions provided in the ride-on lawnmower with front cutting’s instruction manual ).

ASSISTANCE AND REPAIRS

This manual provides all the necessary information to run the machine and for correct basic maintenance operations which can be performed by the user. Any regulations and maintenance operations not described herein must be carried out by your Dealer or Authorized Service Centre, which have the necessary knowledge and equipment to ensure that the work is carried out correctly, maintaining the correct degree of safety and the original operating conditions of the machine. Any adjustments or maintenance operations not described in this manual must be carried out by your Dealer or a specialized Service Centre. Both have the necessary knowledge and equipment to ensure that the work is done correctly without affecting the safety of the machine.

• Only authorized service centres can carry out guaranteed repairs and maintenance.
• Authorized servicing centres use genuine pare parts only. Genuine spare parts and accessories have been designed specifically for the machines.
• Non-genuine spare parts and accessories are not approved and any use of such parts will render the warranty null and void.
• It is advisable to send your machine once a year to an authorized service workshop for servicing, assistance and safety device inspection.

HANDLING AND TRANSPORT

When handling or transporting the accessory, you must:

• Stop the machine
• Wait until the cutting means are stationary.
• Adjust the minimum cutting height (par. 5.1).
•  Release the cutting means assembly from the ride-on lawnmower with front cutting (chap. 4.4).
• Move it along on its wheels (fig. 1.C).

WARRANTY COVERAGE

The warranty covers all material and manufacturing defects. The user must follow all the instructions provided in the attached documentation carefully.
The warranty does not cover damage caused by:

• Failure to read and understand the documentation accompanying the machine.

• Carelessness.

• Incorrect or prohibited use and assembly.

• The use of non-original spares.

• The use of accessories not supplied or approved by the manufacturer.
  The warranty does not cover:

• Wear parts such as drive belts, augers, headlamps, wheels, shear bolts and wires.

• Normal wear and tear.

• Engines. There are covered by the warranty provided by the engine manufacturer in accordance with the specified terms and conditions.

The purchaser is safeguarded by national legislation. The purchaser’s rights, as envisaged by national legislation in the country of use, are not in any way affected by this warranty.

MAINTENANCE TABLE

MACHINE
Check all fasteners| –| Before each use| 7.
Safety checks/check controls| –| Before each use| 6.
General cleaning and inspection| –| At the end of each use| 7.
Check the cutting device for wear| –| Before each use| 8.
Check the drive belt for wear| 25 hours| 25 hours| 8.

TROUBLESHOOTING

after sales service centre.
The cutting means assy is full of grass.| Clean the cutting means assembly
2.^>Uneven cutting| Inefficiency of the cutting means| Contact your local dealer
Forward speed too high in relation to the height of the grass being cut| Reduce the forward speed and/or raise the cutting height (par. 5.1)
Wait for the grass to dry
3.^>The cutting devices do not engage or
do not stop quickly when disengaged.| Problems with the engaging system or the cutting means drive belt.| Contact an authorised assistance centre.

If problems persist after the operations above have been performed, contact your dealer.

UK DECLARATION OF CONFORMITY
(Supply of Machinery (Safety) Regulations 2008, S.I. 2008 No. 1597, Annex II, part A)

1. The company: ST. S.p.A. – Via del Lavoro, 6 – 31033 Castelfranco Veneto (TV) – Italy

2. Hereby declares under its own responsibility that the machine:
   Cutting-means assembly (interchangeable equipment)/grass cutting
   a) Homologation type: 85C, 85C E, 85C QF, 95CV, 95CV E, 95CP, 95CP E, 95C E QF, 95CP E QF, 100C E, 100C E QF, 105C E, 105C E QF, 110C E, 110C E QF, 125C E, 125C E QF, 125C H, 135C H, 155C H
   c) Serial number: 22A••FMC000001 ÷ 99L••FMC999999
   d) Engine:

3. Conforms to UK Regulations:
   • S.I. 2008/1597 – Supply of Machinery (Safety) Regulations 2008
   • S.I. 2012/3032 – The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012

4. Reference to harmonised standards:
   EN ISO 5395-1:2013 + A1:2018
   EN ISO 5395-3:2013 + A1:2017 + A2:2018
   EN 63000:2018

n) Person authorised to compile the technical file:
ST. S.p.A.
Via del Lavoro, 6
31033 Castelfranco Veneto (TV) – Italia
o) Castelfranco Veneto, 01/11/2022
CEO Stiga Group
Sean Robinson

UK Importer:
STIGA LTD
Unit 8, Bluewater Estate Plympton,
Devon, PL7 4JH, England

EC Declaration of Conformity
(Machine Directive 2006/42/EC, Annex II, part A)

1. The Company

2. Herby declares under its own responsibility that the machine: Cutting-means assembly (interchangeable equipment)/ grass cutting
   a) Type / Base Model
   c) Serial number
   d) Motor:

3. Conforms to directive specifications:

4. Reference to harmonised Standards
   n) Person authorised to create the Technical Folder:
   o) Place and Date

© by STIGA S.p.A.
The content and images in this User Manual were produced expressly for STIGA S.p.A. and are protected by copyright – any unauthorised reproduction or modification to the document, either partially or in full, is prohibited.

STIGA S.p.A.
Via del Lavoro, 6
31033 Castelfranco Veneto (TV) ITALY
STIGA LTD (UK Importer)
Unit 8, Bluewater Estate Plympton,
Devon, PL7 4JH, England

Documents / Resources

| STIGA 95C E QF Series Cutting Machine [pdf] Instruction Manual
85C QF Series, 95C E QF Series, 95C E QF Series Cutting Machine, Cutting Machine
---|---

References

• open

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>