Logitech Z-LTE-WW 4G LTE WW Datalogger Instruction Manual

: October 30, 2023
: Logitech

Table of Contents

Logitech Z-LTE-WW 4G LTE WW Datalogger
Product Information
PRELIMINARY WARNINGS
MODULE LAYOUT
SIGNALS VIA LED ON THE FRONT PANEL
TECHNICAL SPECIFICATIONS
ELECTRICAL CONNECTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Logitech Z-LTE-WW 4G LTE WW Datalogger

Logitech-Z-LTE-WW-4- LTE-WW-Datalogger-product

Product Information

The Z-LTE-WW and Z-LTE-EU are modules that are used for digital input and output, totalizers, counters, and analog inputs. The module has an internal UPS with rechargeable backup batteries that can last up to one hour. It also has a communication port for RS485 COM1 on the rear IDC10 connector, RS485 or RS232 on terminals M10-M11-M12, Ethernet 100 base T, and micro USB on the side socket. The module is equipped with a 4G/LTE modem (Z-LTE-WW or Z-LTE-EU) that supports GPS/GLONASS/BeiDou(compass)/Galileo/QZSS GNSS.

Product Usage Instructions
Before using the module, please read the entire manual carefully. The module should only be used by qualified electricians. Specific documentation is available via QR-CODE shown on page 1. The module is sensitive to electrostatic discharges.
Take appropriate measures during any operation. To dispose of the module, surrender it to a collection center authorized to recycle electrical and electronic waste. The product warranty shall become null and void in the event of improper use or tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if the instructions contained in this manual are not followed. The module can be mounted on a 35mm DIN rail in a vertical
position according to IEC EN60715 standards. The digital inputs are configurable as PNP or NPN with a voltage of 8V (Max. 24Vdc). The maximum frequency is 30Hz, and the absorbed current is 3mA @ 12Vdc and 10mA @ 24Vdc.

The module has four 32-bit totalizers on non-volatile memory and four 32-bit resettable counters on non-volatile memory. There are two digital outputs with SPDT free contact relay, with a maximum voltage of 250Vac and a maximum current of 2A. For communication, the module has a communication port for RS485 COM1 on the rear IDC10 connector, RS485 or RS232 on terminals M10-M11-M12, Ethernet 100 base T, and micro USB on the side socket. The module is equipped with a 4G/LTE modem (Z-LTE-WW or Z-LTE-EU) that supports GPS/GLONASS/BeiDou(compass)/Galileo/QZSS GNSS.

PRELIMINARY WARNINGS

The word WARNING preceded by the symbol indicates conditions or actions that put the user’s safety at risk. The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the instrument or the connected equipment. The warranty shall become null and void in the event of improper use or tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if the instructions contained in this manual are not followed.

Logitech-Z-LTE-WW-4- LTE-WW-Datalogger-fig-2

MODULE LAYOUT

Logitech-Z-LTE-WW-4- LTE-WW-Datalogger-fig-3

SIGNALS VIA LED ON THE FRONT PANEL

SIGNALS VIA LED ON FRONT PANEL

LED| STATUS| LED meaning

PWR

(Green)

| ON| Log not active and status waiting for startup
Slow flashing| Log active and status in normal operation
Flashing intermittently| Status in operation from backup battery (battery life 1 hour)
Fast flashing| Error, see Webserver diagnostics
Off| Device OFF

(GSM LEVEL)

(Green)

| ON| Maximum signal (Level 4)

Flashing

| 3 flashes (Level 3)
2 flashes (Level 2)
1 flash (Level 1)
Off| Minimum signal
GSM (STATUS)

(Yellow)

(Yellow)

(Red)

| Slow flashing| Activity in the RS485 or RS232 serial interface
Off| RS485 or RS232 serial interfaced not used
Fast flashing| Timeout in the RS485 or RS232 communication

SD

(Red)

TECHNICAL SPECIFICATIONS

CERTIFICAZIONI| Z-LTE-WW Z-LTE-EU

Logitech-Z-LTE-WW-4- LTE-WW-Datalogger-fig-5

https://www.seneca.it/products/z-lte- ww/doc/CE_declaration https://www.seneca.it/products/z-lte/doc/CE_declaration

---|---
INSULATION| Digital

ENVIRONMENTAL CONDITIONS

| Temperature: -25– + 50°C / (-10– + 40°C if the internal UPS is used). Humidity: 30%– 90% noncondensing.

Storage temperature: -30– + 65°C / (-20– + 45°C < 6 months if the internal UPS is used). protection rating: IP20.

ASSEMBLY| IEC EN60715, 35mm DIN rail in vertical position.
INTERNAL UPS| Rechargeable backup batteries. Duration: up to 1 hour.
CONNECTIONS| Removable 3-way screw terminals, 5 mm pitch for cable up to 2.5 mm²,

Rear IDC10, RJ45 socket, Micro USB socket and 2 SMA for 4G antenna and GPS antenna.

POWER SUPPLY| Voltage: 11 ÷ 40Vdc or 19 ÷ 28Vac 50 ÷ 60Hz. Absorption: 8W.

DIGITAL INPUTS

| Number of channels 4. Configurable PNP or NPN. Voltage OFF<4V, ON>8V (Max. 24Vdc).

Max frequency 30Hz. Absorbed current 3mA @ 12Vdc, 10mA @ 24Vdc.

TOTALIZERS| 4 x 32-bit totalizers on non-volatile memory
COUNTERS:| 4 x 32-bit resettable counters on non-volatile memory.
DIGITAL OUTPUTS| Number of channels 2. SPDT free contact relay. Max. voltage 250Vac. Max. current 2A.

ANALOGUE INPUTS

| Number of channels 2. Configurable mA or Vdc.

Voltage input 0 – 30V. precision 0.1% of Full Scale, impedance: 200 kohm. Current input 0– 20mA precision 0.1% of Full Scale, impedance: < 60 ohm. Input protection 40V / 25mA. Resolution 16 bit.

COMMUNICATION PORTS| RS485 COM1 on rear IDC10 connector, RS485 or RS232 on terminals M10-M11-M12, Ethernet 100 base T and micro USB on side socket.
4G / LTE WORLD WIDE MODEM

(Z-LTE-WW)

|

For further information, refer to the User Manual.

MODEM 4G (Z-LTE-EU)| For further information, refer to the User Manual.
GNSS| GPS / GLONASS / BeiDou(compass) / Galileo / QZSS
SD CARD SLOT| Push-push type for microSD and microSDHC 32GB max.
SIM CARD SLOT| Push-push type for miniSIM card 15 X 25 mm
CPU / S.O.| ARM 32bit, operating system: Real Time Multitasking, built- in Webserver and on microSD.

IDC10 CONNECTOR

The illustration shows the meanings of the various IDC10 connector pins if signals are to be sent via them directly.

PROCEDURE FOR MODULE SWITCH-OFF
The module is equipped with an integrated UPS that allows it to remain on even in the absence of external power. To turn off the module, first disconnect the external power supply and then press the PS1 button on the right side of the module for at least 6 seconds. When the button is released, the PWR LED turns off to indicate that the module is turned off.

DIP – SWITCH SETTINGS

DIP-SWITCHES

SW1| Default settings: all DIP switches in OFF position. For more information see the USER MANUAL.

SW2

| RS232 or RS485 settings on terminals 10-11-12 (COM2 serial port)
RS232| ON| | |
RS485| OFF| | |

ELECTRICAL CONNECTIONS

CAUTION
On first start-up, the module must be supplied without any interruptions for at least 72 hours to charge the internal batteries. Switch the module off with the PS1 button before connecting inputs and outputs. To meet the electromagnetic immunity requirements:

use shielded signal cables;
connect the shield to a preferential instrumentation earth system;
separate shielded cables from other cables used for power installations (transformers, inverters, motors, etc…).