onsemi FUSB15201 Dual Port USB Type-C/PD Controller User Manual
- June 4, 2024
- onsemi
Table of Contents
onsemi FUSB15201 Dual Port USB Type-C/PD Controller
FUSB15201 Dual Port USB
Type-C/PD Controller
Start-Up Guide
FUSB15201EVBSUG
Introduction
The FUSB15201 EVB along with the firmware binary provided in the release
package will allow customer a complete evaluation of the Type−C/PD solution as
stand−alone controller. This document aimed to provide user a faster bring−up
to quickly exercise FUSB15201 EVB with the device characteristic listed in
Table 1.
Table 1. FUSB15201 SUPPORTED DEVICE CHARACTERISTIC
| Feature | Firmware (ARM Cortex−M0+) |
|---|---|
| Type−C | Source |
| PD | Provider |
Quick Start−Up Guide
Steps to load and execute binary for faster evaluation:
- Download the binary with filename FUSB15201_v1.0.0.0.bin and the JLINK support files FUSB15200_NVR_Loader.elf, FUSB15200_FLASH_LOADER.elf and the FUSB15201 Flash Programming Guide from onsemi website.
- Install SEGGER J−LINK (Follow the steps in FUSB15201 Flash Programming Guide for how to download and run firmware in FUSB15201 EVB).
Table 2. SUPPORTED PDOs
| Advertised PDOs | Type | Description |
|---|---|---|
| PDO 1 | Fixed | 5 V / 3 A |
| PDO 2 | Fixed | 9 V / 3 A |
| PDO 3 | Fixed | 15 V / 3 A |
| PDO 4 | Fixed | 20 V / 3 A |
| PDO 5 | PPS | 3.3 V − 21 V / 3 A |
FUSB15201EVBSUG
Table 3. FUSB15201 SUPPORTED/ENABLED CONFIGURATION IN EACH PORT
| Feature | Supported | Description |
|---|---|---|
| PD Specification Revision | 3.1 | Supported Revision |
| PD Specification Revision Version | 1.1 | Supported Revision Version |
| SOP* communication | Yes | Supports SOP, SOP’, SOP” |
| Manufacturer Info Message | No | Unsupported Get MFI |
| Data Role Swap to DFP | Yes | Supports swap to DFP |
| Data Role Swap to UFP | Yes | Supports swap to UFP |
| VCONN Swap to ON | Yes | Support for VCONN swap to ON |
| VCONN Swap to OFF | Yes | Support for VCONN swap to OFF |
| Cable Discovery | Yes | Supports for Cable Query |
| Chunk Message | Yes | Support for chunk messages |
| UnChunked Extended Message Length | No | No support for unchunked message with |
extended length
Rp Value| 3A|
VCONN source| Yes| VCONN sourcing support
PD Power source| 60000W| PD capability per port
USB Suspend May Clear| Yes|
Modal Support| No| Disabled modal operation
VDM Messages| Yes| Support for Vendor Define Messaging
Unconstrained Power| Yes|
Product Type| 3| Power Brick DFP VDO
Power Supply Requirement
See EVB User manual guide for the power supply requirement.
Modifying Configuration
Refer to Software Programming Guide if default configuration needs to be
modified and it can be supported by the device characteristic.
All brand names and product names appearing in this document are registered
trademarks or trademarks of their respective holders.
SPECIFICATION
onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or application information provided by on semi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application,
Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>